0
Nissan Trucks and SUVs
Aside from sedans and luxury cars, Nissan also offers extensive product lines of sport utility vehicles (SUVs) and trucks. Some of the vehicles that belong to these product lines are the Nissan Armada, the Nissan Titan and the Infiniti QX56.
1,635 Questions
blower motor has a short. replace blower motor
When you replace clutch master clyender do you have to bleed the slave clyender?
yes you do,also if it has a cluch damper,you need to bleed it also,its bolted on left side firewall or just follow the line coming from clutch master cylinder.good luck.
What is the correct timing for a 1984 Nissan truck with a Z24 engine?
The same way you set the timing of any Z24 engine. The vehicle it is in makes no difference. Do you know how to use a timing gun.
How do you put back alternator on 88 Nissan hardbody D21?
REMOVAL & INSTALLATION
On some models, the alternator is mounted very low on the engine. On these models, it may be necessary to remove the gravel shield and work from beneath the truck in order to gain access to the alternator.
- Disconnect the negative battery cable.
- Remove the alternator pivot bolt. Push the alternator in and remove the drive belt.
- Pull back the rubber boots and disconnect the wiring from the back of the alternator.
- Remove the alternator mounting bolt and then withdraw the alternator from its bracket.
To install:
- Position the alternator in its mounting bracket and lightly tighten the mounting and adjusting bolts.
- Connect the electrical leads at the rear of the alternator.
- Adjust the belt tension as detailed in http://wiki.answers.com/8585CH01_1.xml.
Starter solenoid sticking. Replace the solenoid if it is external. If it is internal, then just replace thee starter. It will cost a little more but you will have a new starter and solenoid.
84 Nissan pickup why would it pop or sputter?
It could be a intake or exhaust manifold leak.Dirty fuel filter,check air filter,check vacuum lines,check charcoal canister filter,its on bottom,just remove from spring and tilt up .it cost 2.00 at auto zone,check catalac converter,have you been having carb. problems,Ihave 85 with z24 engine,Ireplaced carb. with a weber 32/36 carb. kit,you can chech them out at weber direct.com,but you have to get carb. kit,it will change your vacuum lines and eliminate a lot of valves and you will plug some outlets too,they don't give you a diagram for the changes,but if you decide to get one ,I will show you a diagram,go to you tube and look up 85 Nissan 4x4 silverbullet and check out my video,if you can leave a comment,thanks,tom
Yes it has 2 speed sensors. On is in the trans. And the other is in the speedometer head.
Overdrive is designed and set to only work when you are at full throttle. The overdrive switch is located at the end of the accelerators travel on your carb or Fuel injection. You can adjust it to work at a lower level,but I wouldn't recommend it as it is only for emergency acceleration and hills.
What is the fuel pressure for a 1990 d21 pickup?
The fuel pressure for a 1990 D 21 pickup is dependent upon the size of the engine. In general, the fuel pressure should be approximately 20 pounds per square inch.
How do you replace a rear indicator bulb in a qashqai?
To replace the rear indicator bulb in a Nissan Qashqai, start by opening the rear hatch and locating the tail light assembly. Remove the screws or clips securing the tail light unit, then gently pull it away from the vehicle. Twist the bulb holder counterclockwise to remove it, replace the burned-out bulb with a new one, and reassemble the tail light by reversing the steps. Finally, test the indicator to ensure it’s functioning correctly.
What is correct timing for 1992 Chevrolet 57 liter pickup truck?
There should be a sticker on the radiator shroud that gives timing and spark gap values. All the Chevys I've done say 0 degrees btdc. Warm up the engine. Turn it off and unplug timing wire. On later models, the connector is located near the distributor (except for 1995 models; on these, it's located under the dash, below the glove box). Tan wire with a black stripe. Set timing to 0. Turn engine off. Plug timing wire back together. Reset ECM. ECM will recalibrate after driving a while.
How do you install thermostat on 89 Nissan pickup truck?
THERMOSTAT REMOVAL & INSTALLATION
1989 NISSAN TRUCK
See Figures 1 through 7
- Drain the engine coolant into a clean container, so that the level is below the thermostat housing.
CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
If necessary, disconnect the upper radiator hose at the water outlet.
- Loosen the securing nuts, then remove the water outlet, gasket, and thermostat from the thermostat housing.
- When installing the thermostat, always use a new gasket with sealer and make sure the thermostat spring is facing the inside of the engine. The water outlet housing on VG30i and VG30E engines has the letters UPR and an arrow embossed on the flange edge; they should always be pointing up. The KA24E, VG30i and VG30E engines have a jiggle valve on the thermostat which should always be facing up. Water outlet mounting screws should be tightened to 12-15 ft. lbs. (16-21 Nm) on all engines but the KA24E, which should be tightened to 5-6 ft. lbs. (7-8 Nm). Refill and check the coolant level.
Where is the frost plug on a 1986 Nissan pickup 3.0 v6?
That would be right next to the blinker fluid hose that goes into the block.
Where are the timing marks for Nissan Serena 2.3 diesel 95?
The timing marks are on the belt and the sprockets. not on the engine! the box that the belt is supplied in shows the mark locations. well i use Gates belts and these do!
How do you change starter on a 1996 Nissan truck?
First: Remove negative terminal on battery so you have no potential voltage at the starter.
It is one of the easiest of jobs doing yourself. First, jack up the front passenger side of the truck. Remove the tire. Now, carefully remove the rubber/plastic skirting in the fender well to expose the side of the engine where the starter is. Remove the two "easy to reach bolts" holding the starter in place. Unplug starter at connector. Remove main cable from battery but "remember the position/direction it is in to avoid difficulty" with the re-installation of new starter. Reverse process & surpise, job well done. Skirting might be old, so have large fender washers and self-tapping screws to re-attach skirting into place if plastic tabs are broken. Note: Be careful screws don't puncture anything on the other side. 1/2 long screws work well. Paint flat black to hide and reinstall the tire. Great job.
How do you change the license plate bulbs on a 1997 Nissan Pathfinder?
through the rear package compartment under the matting
What is the horsepower for the 1987 Nissan d21 pickup. With a 2.4 liter z 24 8 spark plug engine?
103 hp.
What is the plug gap on 2004 Durango 4.7?
How do you replace an air conditioning compressor in your 1993 Nissan Pickup Truck?
you need to drain all the freeon out of the system. take the belts off. and take the bolts on the compressor out. its best to get under the truck. and there is a lot of wiggling to get out.
1993 Nissan pickup ext cab se v6 4x4 No turn signals or hazard lights?
try the flasser cam its under the dash
