0
Oldsmobile Cutlass
The Oldsmobile Cutlass was a compact/mid-size car produced by General Motors from 1961 to 1999. The Cutlass was one of the most popular nameplates in the vehicle industry during the 1970s.
1,158 Questions
Why is the speedometer in my 1972 cutlass shaking constantly?
Assuming this happens while you are moving you probably need to replace the speedometer cable.
Why does the 91 Oldsmobile cutlass supreme have no spark?
There could be a couple reasons why your car has no spark. * A bad ignition module, which is located beneath your coils * A bad computer * A bad crankshaft position sensor * Faulty wiring I would probly start with the Sensor, or the ignition module, and work you way from there. The ignition module can be tested at you local Autozone. The Crank Pos Sensor is a real pain to get out, has been known to break off in the block, causeing even bigger problems, and is just located in a ackward spot. If your a little faint of heart on tackling a project like this, I would recomend a trip to the dealer, or a local shop.
Where is the Convertible top fuse located on a cutlass?
It is important to know the location of the fuses of the electrical components of a vehicle. The convertible top fuse in a Cutlass is located in the fuse box under the dashboard.Ê
How do you remove 1987 cutlass dashboard?
trhat requires a lot of work, try and find an old palmer or hanes manual ,they will have that procedure in there, usually i find old manuals on e-bay at good prices.,good luck and good hunting.
How do you change the headlights on a 1997 Cutlass?
It depends on if its a 2 door or a 4 door. I have a 1997 Cutlass Supreme SL, 4 door, and you can just turn the thingy (technical term) that holds the bulb, pull it out of the assembly, and put the new one in.. 2 door, I have no idea :)
You have to change the entire headlamp assembly. Remover the trim ring then the old headlight can be taken out.
How do you change the headlight on a Cutlass Supreme 1994?
Is this a sedan or coupe/convertible? The sedans had the common setup and the coupe/convertibles had the mini-quads.
How do you change the thermostat on a 1989 Cutlass Ciera?
the thermistat is located inside the upper radiator hose, where it connects to the motor. have the car off and cold. just unbolt it and pull the old w/gasket. replace with new and gasket. bolt in. the attach hose. top off antifreeze
How do you change your Oldsmobile points distributor to a HEI and not mess up the timing?
It's the same on a Chevy pull your distributor cap see what position the rifle buld is facing and drop the electronic dust. In the same position and wire it up and add an ignition power to the distributor.
How many 1984 cutlass calis made with t tops?
There is no way to find out the true production number of such a combination, but it was not a very common one.
How much horsepower does a 1969 cutlass s with a 350 rocket and 2bbl carburetor have?
Could be in the 300 neighborhood with decent compression ratio. You can boost that with intake, headers, etc. etc. etc. Good heads are the key. You should research the ones you have & find out the chamber size then you will know if room for improvement. Up or down on chambers changes your comp. & you can only run so much.
Where is the starter in a 88 Oldsmobile?
Bottom side of the engine. Look for something with a big wire and a couple of small wires attached to it. DON'T loosen anything until you take the negative lead off the battery.
What is the firing order for a 1989 Oldsmobile Cutlass Ciera v6?
If it's the 3.1L, then it's 1-2-3-4-5-6.
How do you change the tail light bulb on a 1981 Olds Cutlass?
There should be some carpet or other material covering the bulb in the trunk move this out of the way then u should be able to access the bulb holder it should be about a quarter turn to get it out then the bulb should be a short counter clockwise turn while pushing in at the same time to remove the bulb, installation is the reverse of what you did.
How do you replace the lower ball joint on a 1993 Oldsmobile Cutlass Ciera?
Only one ball joint is used in each lower arm. The MacPherson strut design does not use an upper ball joint.
Care must be exercised to prevent the halfshafts from being overextended. Support the lower arm.
Loosen the wheel nuts, raise the car.
Place a jackstand under the vehicles frame or suspension support.
Lower the vehicle slightly, so that the weight of the vehicle rest on the jackstands and not on the control arms.
Remove the tire and wheel assembly.
Install a CV-boot protector.
Remove the steering knuckle bolts, then remove the ball joint nut and cotter pin from the steering knuckle.
Use a 1/8 in. (3mm) drill bit to drill a hole approximately 1/4 in. (6mm) deep in the center of each of the three ball joint rivets.
Use a 1/2 in. (13mm) drill bit to drill off the rivet heads. Drill only enough to remove the rivet head.
Use a hammer and punch to remove the rivets. Drive them out from the bottom.
Loosen the stabilizer shaft insulator nuts, then remove the ball joint assembly.
To install:
Install the new ball joint into the control arm. Secure the three ball joint nuts, see your instructions supplied by the part supplier for tightening specifications.
Install the ball joint into the knuckle pinch bolt fitting. It should go in easily if not, check the stud alignment. Install the pinch bolt from the rear to the front. Tighten to 40 ft. lbs. (50 Nm) for 1982-84, 33 ft. lbs. (45 Nm) for 1985-93 and 38 ft. lbs. (52 Nm) for 1994-96.
Remove the CV-boot protector.
Tighten the stabilizer shaft clamp insulator bolts to 32 ft. lbs. (43 Nm).
Install the wheel, hand-tighten the lug nuts.
Raise the vehicle slightly to allow removal of the jackstands.
Remove the jackstands, then lower the vehicle, tighten the lug nuts to 100 ft. lbs. (136 Nm).
Will a synthetic oil get rid of a noisy lifter in a 1994 Oldsmobile Cutlass Supreme?
Not likely. If you have a noisy lifter then its oil port is probably plugged because you didn't change the oil and it's too late for synthetic oil to help you. Try it, though, because the alternative is a lot more costly.
How do you remove the door panel on a 1989 olds cutlass cierra?
Using a screw driver, remove the screws and the clips holding the panel to the door frame. Pull the panel away gently and remove any wire connectors, then pull the panel off the rest of the way.
Will a 1966 cutlass hood fit a 1967 cutlass?
It wouldn't match up in the front due to the 67's wider headlight design
How often does an egr valve need replacing?
I never knew my 2000 Honda Accord (165,000 miles) had an EGR. I have replace or cleaned PCV. I have used Engine System Cleaners regulary. Car is running fine. Knock on wood. Same for 1990 Toyota Camry (244,000) when traded.
Considering it doesn't sound like it is stock it's impossible to tell how much HP it has without knowing exactly what has been done to it.
How do you replace the turn signal switch on a 1985 Cutlass Supreme?
Remove steering wheel (with wheel puller), remove lockplate (with lockplate remover), remove 3 screws that hold turn signal switch, unplug switch at bottom of column, fish out the wires, install new switch, fish in new wires.
Where is the thermostat located on a 1992 olds cutlass ciera?
Look in the removable housing at the engine end of the upper radiator hose
How do you hook up a tach in a 72 Olds Cutlass?
Assuming there are at least four wires coming out of the tach, the green one goes to the negative side of the coil, the red one goes to a keyed power source, the black one goes to a ground and the last one is for illumination and can be connected to the dash light circuit.
Why is your 1986 Oldsmobile cutlass smoking?
My 1986 cutlass supreme w/307 was smoking bad, and I tore the motor down and the rings were shot.
Where is the radiator drain petcock on a 1992 Oldsmobile Cutlass Cierra?
On the back of the radiator, driver side.
