Toyota Camry

4 cylinders are so called interference engines. It means if your timing belt breaks your engine is basically done. And you will have to have major overhaul.

It does not have one, it uses injectors.

In 2010, for northern hemisphere winter begins on December 21.

For southern hemisphere winter begins on June 21.

In 2011, for northern hemisphere winter begins on December 22.

For southern hemisphere winter begins on June 22.

We have H and M buttons right below the clock. Hold on H button to change hours and M button for Minutes.

See this video below for more help:

well it depends on the year really and how many miles and the transmission and timing belt and how well you have takin care of it all i know is i live in the Midwest and my 1997 Camry got up to 120 will 140,000 on it so its got some balls

No, most automobiles do not have a specific deceleration indicator light. However, some modern vehicles may have warning lights that come on when there is a significant change in speed, which can indirectly indicate deceleration. It's important to rely on your vehicle's existing indicators and gauges to monitor deceleration.

no. however your indicator lights are located in your dashboard. dashboard light will light up when you turn your headlights on. Ex. the lights that are illuminated behind your miles per hour needle or behind your fuel gauge. Your indicator light are a lights that come on when your first turn the ignition. these lights indicate when your oil needs to be changed or your fuel is low or your washer fluid is low or the blue light that is illuminated when your headlights are on bright or high beam etc.....most newer model cars are equipped with the indicator lights. hope this is helpful.

The 1999 Toyota Camry uses H4 halogen bulbs for its headlights. It is recommended to consult the vehicle's owner's manual for specific bulb numbers and replacement instructions.

To reset a breaker move the handle completely to the off position. If it had tripped you will feel a little resistance as it goes to the off position. If this doesn't restore the power the breaker is either bad and in need of replacement, or there is a persistent fault in the circuit causing the breaker to immediately re-trip. Breakers are safety devices.

This is usually a telephone company term.

It refers to the main bundle of cable(s) coming out of a central office or other centralized telephone switch (computer) It is based on the way a tree grows: There is the trunk, then the branches, then the twigs It does not refer to cable that comes out of an elephant's head or the storage compartment of your car.

There is a small rectangular slot on the right side (passenger side) of the transparent cover/lens. Put a properly fitting (not too small, not too big) flat screwdriver in the slot and leverage the cover/lens downward. It should pop out. Don’t be too rough, but you can apply some force—the cover is fairly strong. After that it is easy to pull the light bulb from between the spring terminals. Put the new bulb in and pop the cover back in its slot.

High hydrocarbon emissions from a vehicle may be caused by improper ignition timing, faulty ignition, misfiring problems, vacuum leaks, worn piston rings or valves or an exhaust gas recirculation system incorrectly operating at idle. One fouled spark plug can result in extremely high hydrocarbon emissions. You car is 14 years old and probably has high mileage. Start by replacing the spark plugs and plug wires. Replace every single vacuum line under the hood. Replace them one at a time, so as to not get confused. Clean you EGR Valve of any carbon deposits, and make sure it is functioning correctly. Pour a can of a good Fuel Injector cleaner such as Seafoam or Techron in a full tank of fuel. Leave the cheap stuff on the shelf, as is does very little good. To remove built up carbon deposits, inject it through the intake by following the directions on a can of Seafoam. Have someone check the timing on this vehicle. A compression check will verify if you have worn rings or a burnt valve.

torque 39 nm (29 ft-lb) then 90 degrees then another 90 degrees 2 small bolts at front 21 nm (15 ft-lb)

Should be drain plug on engine side of radiator down towards the passenger side. Drain fluid and dispose of properly. There is no easy way, remove hoses connected to the radiator at the radiator and electrical fan housing this should have a wire connecting plug. You will not have to take off the front of the car. just work your way from the hoses to the radiator. If you feel that you will have problem remembering where things go use masking tape and marker to label. Example take two pieces of tape and write # 1 on each place one on the item your removing and the other on the spot where you removed it from.

This process takes around an hour and a half. I recommend you doing it your self as the dealer quoted me hundreds with time involved. Lexus made these cars so they make it so you bring it in to the shop! You need these tools: screwdriver, socket wrench, and strong hands. You will need to first dissemble the battery to get your hand behind the headlamp and twist the two prongs and pull out. The front engine plastic housing has to be removed and a safety bar. Remember not to touch your new headlamp bulbs or else it will limit there life span. It's simply easy once you have your hand behind and twisting the plastic prong behind the light!

18.5 gallons full capacity

how do i reset srs light on scion tc

0.248 miles.

Actually Camry in Europe is better then in US. European Camry is more expensive and sells in US as Lexus. 2012 Camry that sells in US is ugly.

Depends on your vehicle model, but probably a set of wrenches and/or a socket set will suffice.

They're frequently located in difficult to reach areas, so you might want those to be long-handled offset wrenches. In some cases, you can come in through the wheel well, so whatever it takes to remove the mud guards from there could be useful also.

You will need to take the current shifter cable off, and to do so you'll need to open the dash and console so you can reach the plate keeping the cable in place. Next, thread it (the replacement) through the firewall, and this area, and connect it. Put everything back together after making sure it is secure, and you're done.