0
Toyota Corolla
The Corolla is a series of compact/subcompact cars produced by the Japanese automaker Toyota Motor Corporation since 1966. In 2007, the Corolla became the world’s best-selling model, with more than 35 million cars sold.
4,409 Questions
Why is it hard to shift in reverse and shift gears on a 1995 Toyota Corolla?
Odds are the clutch is in need of a adjustment or replacement.
Reset check engine light 1996 Toyota corolla?
Go to Autozone or Advance Auto and borrow their OBD2 scanner and reset it. Easy and free to use
P0420 on a Toyota corrolla verso 1.8?
Trouble code P0420 means:Catalyst system efficiency below threshold
Where can one purchase a 2000 Toyota Corolla?
Generally speaking New Car Dealers won't have 13 year old cars in their inventory, they get them in trade~in they send them off to auction, On line try CarGurus.com, AutoTrader.com Cars.com or if you live in a reasonably large City, there is usually a place with a bunch of used car lots..all in a row. But my best suggestion is shop on line at those sites..CarGurus is pretty good, the have 'price analysis' to guide you if it is overpriced or a good deal, and you can confine your radius to a area you pick. Beware if you live in California, there are emissions packages good for 49 States, then Calif and it must have the 'smog' package to register it. You have far more choices outside California. Best of luck with you shopping, folks tend to hold on to their Corollas, the perfect blend of power and economy. They hold re sale value better than any other car in it's class.
How do you reset the maintenance required light on an 2005 Toyota Corolla?
set your mileage on your actual mileage reading, not a setting measuring your trip. Keep hold down the button until it resets itself.
My Toyota manual for a 1991 Corolla DX says that error code #71 is used only for California specifications. Here is the official diagnosis, according to the manual: the EGR gas temperature sensor signal (THG) is below the total temperature of the intake air temperature plus 55 deg Cent. (99 degrees F) after driving for 25 seconds in EGR operation range. The manual then lists five trouble areas: 1- Open in EGR temperature sensor circuit; 2- Open in VSV circuit for EGR, 3- EGR vacuum hose disconnected, valve stuck; 4- Clogged in EGR gas passage; 5 - ECU.
Where is cabin air filter on 2005 Toyota Corolla?
The cabin air filter is located behind the glove box. The glove box has two small screws holding the glove box to the dash frame. Open the glove box, unscrew these and the whole thing drops down. A plastic tray cover is located here and the filter simply slides in and out. I replaced mine and my musty smell disappeared. Good luck.
How much to fix a power steering pressure tube in a Toyota Corolla?
Well I just bought the hose to replace mine. We paid about $30 for the hose itself. I haven't replaced it yet so I don't know how long it will take but I don't explect more than about an hour. Most shops charge $70-80 an hour. Good luck. These are great cars!!!
Does a 2003 Toyota Corolla have a timing chain or timing belt?
Actually, I believe all 2000 and up models have chains. I checked for our 2000 Corolla on Rockauto, and a chain comes up. This is what is stated on Toyota discussion sites.
What size wiper blades for a 2008 Toyota Corolla s?
The 2008 Toyota Corolla takes 24" drivers and 18" passenger side wiper blades. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only. Be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.
A zerk is another term for a grease nipple - a metal filling used in mechanical systems to feed lubricants.
you might check Oriellys or Auto zone they should either rent or sell them
It has no differential plug.
Where might one purchase a Toyota Corolla AE86?
A Toyota Corolla AE86 might be found at a used car lot. Also some classifieds may have this model for sale through a private owner who wants to sell it.
What causes a 2001 corolla to have lean fuel trim in bank 1?
If you get DTC code P0171 or P0172 then It could be Mass Air Flow sensor gone BAD. Clean it or repalce it.
This happened on my Corolla when the little spring lever popped out of the fuel cap. Just pull pack the carpet in the truck which lines the quarter panel just behind the fuel cap. You will see the release handle there. Be prepared to get weird looks from people when you open your trunk up after you pull up to the pumps.
open the trunk. remove the retainers that hold the carpet that goes all around the trunk (you might wanna start from the ones near the taillight). move the carpet aside so you can see the gas door from the inside. you will see the spring-loaded catch that locks the door. push it.
and in case the wire is not attached or torn, you may have to replace or reattach (if you are lucky) it. for replacement, get some brake wires of a mountain bike. and then get a mechanic to help you out with the rest.
Not sure if it applies to this model, but other Toyotas I've seen have a little spring clip that "pops" the door open once the latch is released. If the clip is gone, the lever releases the latch, but the door doesn't open up. You can easily pry it open with a knife (while an assistant lifts the lever). Use a bent piece of metal to fashion a replacement spring and glue it into place. It helps if you have another Toyota nearby to see how the thing is supposed to work. The dealer may have a part you can buy, if you don't have anything that will fit the bill.
How do you change a timing belt on a 1989 Toyota Corolla?
Removal (1988-92 Corolla)
# Raise and support vehicle. Remove right front wheel and engine undercover. Remove washer tank. Loosen water pump pulley bolts, then remove all accessory drive belts. Remove valve cover. # Disconnect engine wiring harness from upper timing belt cover. Rotate crankshaft so that No. 1 cylinder is at TDC of compression stroke. Notch in crankshaft pulley must align with "0" timing mark on timing belt cover. # Support weight of engine with a floor jack. Remove engine mount at timing belt end of engine. # Remove water pump pulley. Remove crankshaft pulley bolt. Using gear puller, remove crankshaft pulley. Remove timing belt covers. Remove timing belt guide (large washer) from crankshaft sprocket. # If reusing timing belt, mark direction of rotation on timing belt. Match mark timing belt with marks on both sprockets for installation reference. Place arrow on belt to indicate original direction of rotation. # Loosen idler pulley (tensioner) bolt. Push idler pulley as far to the left as possible, and snug tighten bolt. Remove timing belt. Inspection (1988-92 Corolla)
# Check timing belt teeth for cracks or damage. If tooth damage is found, ensure camshaft and crankshaft sprockets are okay. If wear or cracks on flat side of belt face are found, check for nicks on idler pulleys. If wear or damage to only one side of belt is found, check belt guide and alignment of each pulley and sprocket. # Check free length of idler pulley tension spring. Replace spring if free length is not 1.51" (38.4 mm). Check tension at installed length. Tension should be 8.8 lbs. at 1.976" (4 kg at 50.2 mm). Installation (1988-92 Corolla)
# Ensure No. 1 cylinder is at TDC on compression stroke. Crankshaft key will be at 12 o'clock position, and timing mark notch on crankshaft sprocket will align with timing mark on oil pump housing. . Hole in camshaft sprocket must align with mark on bearing cap. NOTE: Engine should be cold when installing timing belt. # Ensure idler pulley (tensioner) is pushed as far to the left as possible and pulley bolt is snug tight. If reusing old timing belt, install belt and align match marks made during removal. Install new timing belt. # Loosen idler pulley (tensioner) bolt and allow pulley to move against belt. Rotate crankshaft CLOCKWISE 2 revolutions from TDC to TDC. # Recheck timing mark alignment. If timing marks are not aligned, remove and reinstall timing belt. # With idler pulley bolt still loose, measure timing belt deflection at midway point of belt longest run. Deflection should be .20-.24" with pressure of 4.4 lbs. (5-6 mm at 2.0 kg) applied. If deflection is not as specified, readjust tension on belt by moving idler pulley (tensioner). # Tighten idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install timing belt guide to crankshaft sprocket. # Install timing belt covers. Install crankshaft pulley. Tighten center bolt to specification. See TORQUE SPECIFICATIONS . When installing valve cover, ensure sealant is apply in correct positions. ee Fig. 6 . # Install water pump pulley. Install accessory drive belts. Adjust drive belts to proper tension. Final tighten water pump pulley bolts. # Install front wheel and engine undercover.
Why does your my light and emergency brake light stay on my 2004 dodge Dakota?
Check Brake fluid level in master cylinder and make sure Emergency brake is fully released
2003 Toyota Corolla fuel filter?
According a recent visit to Toyota dealership, it appears that the fuel filter is located inside the fuel pump. That is, you need to remove the fuel pump in order to change the fuel filter wich is part of the full assembly.
When was the first Toyota Corolla XRS put on the market?
The Toyota Corolla XRS was put on the market in 2003. This model was released with a 1.8 litre four-cylinder DOHC engine, 170 horsepower and 127 pound-feet of torque. It's made more sporty than the original Corolla, and costs a little more.
How do you calculate cc of an engine?
cubic centimeters is 1000 cc`s for every 1 liter the motor is . ex... 2.0 liter engine is 2000 cc`s and a 5.0 liter would be a 5000 cc engine .
Take the swept volume of each cylinder multiply by the no. of cylinders.
/4 d2 S n
Where R = Bore diameter,
S = Length of stroke
n = No. of cylinders
Measured in cm3 of water which is equivalent to 1 liter.
How do you replace the rear window on a 1997 Toyota Corolla?
simple to do it the cheap way you go to a junk yard find a 97 Toyota pay for the back window (they usually take it off for free) u take it slide it in the back and take a caulk gun and run down the sides and top and bottom then u scrape off the exes caulk and let it dry
