Toyota Sequoia

The Volkswagen 1198cc 3-cylinder engines (55, 64, 60 and 70PS) have a timing chain.

The 2003 Toyota Sequoia's engine produces 315 ft-lbs. @ 3400 rpm.

Spark plugs. Check condition of plug wires. ECU sets timing automatically.

6.5 quarts, 5W-30 OIL.

The 2006 Toyota Sequoia has a 9 ft. 10.1 in. (118.1 in.) wheel base.

go to tweeter they will hook you up phat if you have the coin

We are having the same issue in our 2002 Sequoia. We have replaced all the fuses that are on the fuse box cover map that say radio and that did not work. Anybody have an answer? How do we get our radio to work again?

EBay. Or I have a couple of extra ones

It has a belt. It is also and interference engine. Severe engine damage will occur if the belt breaks. Replace at 105,000 miles.

The curb weight of the 2008 Toyota Sequoia is 5680 lbs..

the dash just removes without having to untighten any screws

it has a timing chain 05-08

There should be some carpet or other material covering the bulb in the trunk move this out of the way then u should be able to access the bulb holder it should be about a quarter turn to get it out then the bulb should be a short counter clockwise turn while pushing in at the same time to remove the bulb, installation is the reverse of what you did.

on the tundra faq they said this is the same engine and to pull the battery lead for 10 min. to clear check engine light. they said if the problem still exist the light will come back on within 100 miles.

Autozone parts store will read the trouble codes for free but will not clear the light. Other parts stores also provide this service for free. Call some in your area and ask?

good luck jerry

MAINT REQD is different from an actual MIL. The MAINT REQD light is simply a timer for oil changes.

Here's how you get reset the MAINT REQD light:

1) put the key to the ON position

2) press the mileage reset button on your cluster so it shows total mileage (not trip)

3) put the key to the OFF position

4) press and hold down the mileage reset button, leave it pressed

5) put the key to the ON position

6) wait until the mileage shows 000000 and you can stop pressing the ODO button

If that doesn't work, consult this

http://www.tundrasolutions.com/forums/tundra/115807-reset-maint-reqd-light/

Jack up front corner (I used a jack applied to the square cross section tube (aka frame rail) just behind the front wheel and ~ 2 feet in. Remove front wheel. Get a 14mm ratchet and remove the two bolts that hold the outer part of the caliper to the fixed part of the caliper. Pull (or gently tap with a hammer) the outer part of the caliper off. Rotate and pull the two 14mm pins and rubber boots from the fixed caliper, clean then lube with permatex copper antiseize (install boot first then the pin. Remove the brake pads. Transfer the thin metal inner shim and outer shim holders from the old pands to the new. Install the new pads and reinstall the outer part of the caliper (you may need a c clamp to push the caliper's piston back.) Note, the one pad with the protruding metal tab is on the inside and the tab is on the highest point.

The Yaw Rate Sensor is located under the center storage console and is accessed by removing the center console. I just replaced mine and plan to post a DIY on a Toyota forum.

There is no cabin air filter in the 2002 model. In the later models it is located behind the glove compartment.

If the handle is broken, then you'll have to manually open it. If the locking mechanism is frozen, you will have to manually open it. Generally that means pulling the back panel off and pulling the latch cables by hand. Sequoia forums have detailed information on how to remove the rear panel - fairly simple.

The 2004 Toyota Sequoia is 16 ft. 11.9 in. (203.9 in.) long.

The maximum cargo capacity of the 2003 Toyota Sequoia is 128.1 cu.ft..

A keyless entry remote on a 2001 Toyota Sequoia can not be reprogrammed at home. The key must be taken to a dealership where the engineers can program it with new settings.

To my knowledge there is no button. There is a small recess at the back top edge that you slide your finger in and pull to open. Gently! If you get a clunk when you pull and the filler door stops, your vacuum operated lid lock is in the locked position. Unlock the car and try again. If the filler lid is locked with the car unlocked try started the car to 'charge' the vacuum system. If this does not work you will have to open the trunk to access the lock, and manually push the locking pin back.

There isn't one. Your Suburban only has one washer fluid bottle, but it has two pumps. One for the front windshield and one for the backglass, they are side by side in the reservoir on the driver side inner fender.

there is no release you just push on the door near the hinge and it opens

The 2008 Toyota Sequoia has a 10 ft. 2 in. (122 in.) wheel base.