Buick Riviera

The value of a 1979 Buick Riviera can vary significantly based on its condition, mileage, and any modifications. Generally, prices can range from around $5,000 for a well-used model to over $15,000 for one in excellent condition or with low mileage. Classic car markets and specific auctions may also influence the price, so checking recent sales or classic car valuation guides is advisable for a more accurate assessment.

The amp light on a 1964 Buick Riviera typically indicates a problem with the electrical charging system. Common causes include a malfunctioning alternator or generator, a dead battery, or a fault in the wiring or connections. If the amp light comes on, it suggests that the vehicle is not generating enough electrical power to meet its demands, which can lead to battery drain and other electrical issues. It's advisable to check the charging system components for any faults or failures.

The trunk lock on a 1965 Buick Riviera operates using a simple mechanical system. When the key is inserted and turned, it engages a latch mechanism that releases the trunk lid. This system typically includes a rod that connects the lock cylinder to the latch, allowing for smooth operation. Additionally, some models may feature a release button inside the vehicle for added convenience.

To change the timing belt on a 1995 Buick Riviera, first disconnect the battery and remove any components obstructing access to the timing belt cover. Then, remove the timing belt cover, ensuring you align the timing marks on the crankshaft and camshaft to maintain proper timing. Next, loosen the tensioner and remove the old timing belt, replacing it with a new one while ensuring proper tension. Finally, reassemble the components, recheck the timing, and reconnect the battery.

To replace the fuel pump on a 1993 Buick Riviera, start by disconnecting the negative battery cable to ensure safety. Remove the rear seat cushion to access the fuel pump access panel, then unbolt the panel and disconnect the fuel lines and electrical connector from the pump. Replace the old pump with the new one, ensuring all connections are secure before reassembling the access panel and seat. Finally, reconnect the battery and test the new pump for proper operation.

The fuel pump on a 1985 Buick Riviera is typically located inside the fuel tank. This design is common in many modern vehicles as it helps to keep the fuel pump cool and prevent it from overheating. Accessing and replacing the fuel pump in a 1985 Buick Riviera may require lowering the fuel tank or accessing it through an access panel in the trunk or under the rear seat.

To remove the left or right inside door panel on a 1990 Buick Riviera to replace car speakers, you will first need to locate and remove any screws or fasteners holding the panel in place, typically found around the edges and handle. Once the screws are removed, carefully pry the panel away from the door frame using a trim removal tool to avoid damaging the panel or clips. Disconnect any electrical connectors for power windows or locks before fully removing the panel.

The power antenna fuse for a 1995 Buick Riviera is typically located in the fuse box under the dashboard on the driver's side. You can find the fuse box by removing the cover and looking for a diagram that shows the layout of the fuses. The specific fuse for the power antenna is usually labeled in the diagram. If you’re having trouble, consult the owner’s manual for detailed information.

Vacuum leak.

Could also be the idle air control valve. Read this: http://rds.yahoo.com/_ylt=A0geu5Dx19NHdfsAi8FXNyoA;_ylu=X3oDMTE5MWc1cmxhBHNlYwNzcgRwb3MDMQRjb2xvA2FjMgR2dGlkA1FSVzJfMTE4BGwDV1Mx/SIG=12ug709tt/EXP=1205152113/**http%3a//www.tomco-inc.com/Catalog/27idle%2520air%2520control%2520motors.pdf

The easiest way and the best way to prevent damage is to remove the tire, splash shield and accessory belts then remove the harmonic balancer bolt using the special holding tool DenLors 648796. The balancer or crank pulley will then slide off fairly easy, then reverse this procedure to install the replacement pulley.

Ok, regardless if you are working on the 1.5 or the 1.6 it's a pain in the you know what. The bolt is on very very tight and requires a special tool for ease that is made just for Honda harmonic balancers It holds the balancer in place while you turn the bolt use a large steel pipe or breaker bar with an IMPACT SHALLOW 6 point socket and break it loose. I've only seen a few impact wrench guns that could turn this over torqued bolt. Just DONT break the bolt.. You will be upset...$$$$$

You first need to lift the car off the ground like your changing the tire(get it on a cherry picker if you can for easier access). Take the tire off, loosen the tensioner on the alternator, and get the belt off. Take a 11/16"ths shallow 1/2" socket and a 14" or larger steel pipe for torque because this bolt is very very tight and can easily break your tool. There are a few impact guns to take it off.

According to my manual you can push a large screw driver in a hole near where the speedo cable connects to the gear box to lock the flywheel. I found I had to remove a small bolt to get the hole large enough to fit the screw driver in. A small piece of casing broke and it became very easy to lock the flywheel. The bolt came undone with a socket and a 30 in bar. I don't think the missing casing is going to make any difference.

you have to take off the front cover of dash witch means u will have to take off the cover under the lil over hang part and the screws from the sids of the dash and u will have to pull the climate control out witch is just a few screws near the rear of the c.c. and then there are i think 4 or 5 screws that hold the radio bracket in then one net on the rear of that bracket that holds the radio i give it a 3-10 on a difficulty scale but that is me i did mine in about 2.5 hours but i had to mod some parts cuz i bought the wrong ones

In my '86 Park Ave. 3.8 the starter was just behind the bottom of the rad in the front of the car. In my case I could start the car from the starter but not the ignition then later found out it was not enough cranking power in the battery. Remember when lifting your car to change the starter block both back wheels, front-wheel drive will roll,try battery 1st but starter is not too difficult to change.

If the antenna is stuck up, push it down as far as you can. Then pull back the carpet panel inside the trunk. Take off the wiring plug. You will need a flat screwdriver to push the tabs in on the connector to unplug it. Unbolt and unscrew the unit off of the bracket. Once it is loose, you can pull it through the rubber grommet on the car. If the antenna is too long to be able to pull the unit through into the trunk, just cut the antenna off. Your replacing it anyway.

Good luck!

This is easy, especially since I have the same car and have done this myself. After opening the hood, you must remove the lid to the air filter housing. To do this, loosen the hose clamp from the end of the air intake hose connected to the air box and remove the air intake hose. Then pull the plastic locking tabs inward and lift them from their slots. After lifting the tabs, slide the lid until the other end is free. Now that the lid is removed you shoujld have better access to the headlight bulb. First make sure your headlights are not on, unplug the socket from the bulb and twist the bulb until it is free to pull out. Once you have removed the old bulb replace it with the new one in the reverse order. Be sure not to touch the bulb with your bare skin or get it dirty. Headlight bulbs produce extreme heat and the oils from your skin will burn into the glass and cause the bulb to rupture in a matter of minutes. If you do touch the bulb by accident, wipe it off with rubbing alcohol and a lint free cloth to clean it.

As you fail to mention year and engine size, I will assume it is a 3.8 V6. Firing order for the 3.8 is 1-6-5-4-3-2

rear ryhits bearing

Usually in the ign lock cylinder if you have the VATs type key with the resistor in the key. The wires attached to the key lock cylinder often break. If you have the "pass key" type without the little resistor chip then it is different. But it also usually involves removing the key lock cylinder.

No such thing as a "fuel trim sensor". Where did you come up with that? Fuel trim is a computer adjustment based on O2, MAF, ECT, TPS and other sensors.

I don't know if this would help, but maybe. I just had the same problem on my 1996 Rivera. In my case, there are two main fuse boxes located under the back seat. On your model they may be located somewhere else. AT any rate, I replaced the 30 AMP fuse in one of the boxes and my cigarette lighter started working again. The funny thing is I went to ALLdata & subscribed for $25 per year, well worth it, to get the fuse layout & callouts. My situation was the pwr fuel cap actuator & the trunk release actuator, would not operate, so I couldn't put in gas or open the trunk, as this operated from the door handle console. Once I replaced this fuse, the situation was every thing worked including my cigarette light. Of all the callouts on the fuses, not one called out for "cigarette lighter" Gil Raker

You will need to remove the inside door panel, to do this you will need a couple screw drivers a Phillips and a torx bit set then you will also need a small pry bar for the plastic retainer clips that secure the bottom of the pannel to the door. once you remove all the screws you will need to pull the pannel free from the door at the bottom of the pannel, this is where thee small pry bar comes in. then to remove the pannel after its free from the retainer clips and screws you simply lift up on the door panel and pull it off, be sure to unplug all electric switches that are on the door so you don't pull the wires out of the plugs. once the panel is off there will be your speakers mounted to plastic frames/spacers you want to keep the frame/spacer for the new speakers and be sure to leave the plastic sealed to the door frame after you install new speakers. this helps reduce outside road noise inside the car and also helps act as speaker boxes to optimize the sound from your new speakers. you can look up stereo wiring diagram online to find out what wires are positive+ and negative-. you will need to cut the plug off the wires from factory speaker plug and replace with female wire plug 14-16 guage awg. this will ensure good connections to the speakers, loose wires will cause distortion and that can ruin a speaker fast it can also make sure the speakers work everytime you turn on the radio and wont cut out when you hit bumps or turn corners.

hope this helps, good luck.