How does an off delay timer work?
when off delay timer gets control signal, its NO(NORMALLY OPEN) contact become NC(NORMALLY CLOSED) for preset duration, and then become NO.
How do you get the convertible top down in a 1995 Saab 900S?
If you have followed the procedure in the manual and it will not respond be sure the emergency brake is pulled on because the older convertibles have an interlock switch tied into the emergency brake to stop people from trying to put the top up or down when moving.
This could be your problem.....or not ....the new cars have several sensors that all must work or no top operation and ti can get VERY expensive to keep them working. A friend spent $7K on top repairs over a three year period before he gave up and dumped his car.
I hope you have better results.
Can you fit a 1976 Corvette body on a 1980 Corvette frame?
Yes, the same frame and basic underpinnings were used for that whole generation. The C3 (1968-1982).
How many 1993 Corvette convertibles made?
Almost 5,700 1993 Corvette Convertibles were produce and sold that year.
James
Where is the horn relay located on a 1990 Crown Victoria?
The horn relay on a 1990 Crown Vic is located in a black plastic box that is under the hood, just behind the battery, the lid is held on by simple clips that come off easily. You should see a chart under the plastic lid of this box that will tell you just which relay is the horn relay.
What is the easiest way to change your plug wires in a 1977 Corvette?
from experience...one at a time. not being funny-being safe and saving time.
Air condition does not get cold in a 1998 corvette?
The a/c gas has leaked out of the system and will need to be charges after you have fixed the problem. Looking around 1000 to 4000 to repair.
How much is a 35th anniversary Chevy Corvette with a 4 3 transmission worth?
Depends on overall condition, mileage, options, etc...
According to NADA. Low retail, $9400. Average retail, $13150. High retail, $23500. As already stated, it's all about condition and factory options.
How do you remove the shifter knob on a 1993 corvette automatic?
Remove shift release button off the top of the shifter, inside there is a small snap ring. Remove the snap ring and lift the shifter knob off.
How do you open the hood if the interior hood release doesn't work?
Either get someone to pull and hold the hood release lever open or find some other means, like using the seatbelt, and then try pulling up on the hood. This should pop the hood, and then of course to fully open the hood you would need to find the release latch that is under the hood but above the grill, to the left of center. The hood release mechanism may be stuck or need some lube and a little working.
How do you reset the oil change light on a 1994 Chevy Corvette?
To reset the oil light, put the key in the ignition and turn to accessory setting (but do not start the car) Push the English/Metric button twice and then push and hold the "Gauges" button. The "Change Oil" light will flash for about 15-20 seconds and then go out. Release the button and turn key off.
When you turn the key back on, the light should be out. If it is not, repeat the above steps.
What are the steps taken to remove and reinstall a fuel tank on a 1974 corvette?
Remove the fuel lines. Drain the fuel from the fuel tank. Remove the retaining straps. Reverse the process to install the new fuel tank.
Reason for fuse blowing for ac control head 10 amp on your 1994 corvette coupe?
Fuses are designed to "blow" when current [Amps] above their design rating flows through them and the circuit which they are intended to protect. The "reason" your fuse is blowing is that something is wrong, or has been changed due to someone tampering with the electrical system. The blowing of the fuse is protecting its circuit, the wiring harness in which it runs, and possibly your entire expensive vehicle from serious overheating of the circuit, which if allowed to continue could result in very expensive damage, or total destruction of your vehicle by fire. The most common cause of such overcurrent flow is a short circuit within that circuit in which the fuse blows. Another cause is that someone added some current using device to the circuit that uses more current [Amps] than the conductors [wires] and fuse were designed to carry. Another possibility is that someone who didn't know what he/she was doing miswired the system. Get someone who knows what they are doing [preferably a certified auto electronics technician] to troubleshoot the electrical system, and properly correct any defects found.