0
Combustion Engines
Combustion engines are not only used in road vehicles but also trains, ships, aircraft, military and construction machines.
1,973 Questions
What is the hottest part of an internal-combustion engine?
The combustion chamber. The temperature of the air/fuel mixture combusting is approximately 1800 degrees f.
Does a 1996 Cavalier have a zero tolerance engine?
if by zero tolerance you mean that if the timing goes the valves will get bent then yes it is ^ that is wrong
Non Interference is that term and your engine IS NON INTERFERENCE !!
What size engine does a 2000 Honda civix lx have?
it comes with a dohc 1.6L (b-series) or a sohc 1.6L(d-series) you can find out by looking at the motor.
What do you do if an engine computer is misfiring?
An engine computer does not cause a misfire but merely reports it. The misfire is probably caused by the ignition coil or plug wires
What is engine port deactivation technology?
PDA (Port De-Activation) system which "ensures high exhaust gas recirculation, resulting in combustion stability at low speeds and optimal performance at high speeds together with improved fuel efficiency." The PDA system also reduces emissions.
pre-ignition
Rent a tranny jack. All the internal components are available. the tranny swap is easy, make sure the clutch is good, no use pulling the tranny twice.
first off, what type of trans do you have ( manftr / speeds-gears ) with that type of horse power i hope it's an 18 speed. if you don't have a trans cooler - get one! this will help. remember all that horse power breaks things. use it only when neccesary. my 87 359 has 500hp and my 88 379 has 675hp. easy is the key to cool.
What causes excessive engine rev?
Driving in low gears. Pushing hard on the accelerator ("flooring it"). Going uphill. Driving with excessive weight (like a trailer). Either shift up or lay off the gas to bring your engine speed down. This is a classic symptom of a "worn clutch" in a manual transmission vehicles. The friction disc cannot transfer power under load so it slips under load causing excessive engine reving. Excessive engine RPM at idle can be caused by a vacuum leak or by a stuck Idle Air Control (IAC) valve.
Which are negative impacts that the internal combustion engine has had on society?
efficient travel and noise pollution
What came as the stock engine in a 1994 Ford Probe GT?
How do you turn off check engine light?
need a scan tool wich can be purchased At any parts store or simply disconect battery if it is a hard code will come back on until problem is fixed
What would be the sympton of an open cad cell on an oil burner?
Failure to maintain ignition. The burner will start, but will shutdown within the lockout interval (30-45 seconds), "thinking" there was no flame.
There is a complicated physics/chemistry answer for this question and a "mechanic" answer. I will give the mechanics answer. I am assuming that you are asking this question in regards to a specific amount or volume of gasoline, because the obvious answer otherwise would be that the fuel is being pumped in the engine at a high rate and an open container is just....sitting there. With a specific amount of gasoline, in a container, the amount of gasoline that can be burned at a given time is in direct relation to the amount of surface liquid in contact with the air. In an internal combustion engine the fuel is mixed with air and atomized thereby creating more surface area to burn. Also the fuel air mixture is compressed, which causes heating and makes the mixture easier to ignite by a spark. Simply put, you cant burn something without air, and you can only burn a certain amount of something with a certain amount of air.
David W.
Career Mechanic
How the knocking differs of SI engine with CI engine?
In SI engine knock occur due to spontaneous ignition of end gases , as propagating flame compresses the mixture causes high temp & pressure reaction take place in end gases that burns rapidly with high pressure peak called knock. Where as in CI engine knocking or detonation occur due autoignition fuel & air not mixed homogeneous prior to combustion.
pressure peaks of knock come before Top Dead Center(TDC) in CI engine where as in SI engine it comes after the TDC.
Can you replace your Peugeot 405 engine with a 406 engine?
yes you can im putting a 2.0 8v turbo from a 406 in a 405. wat you wanting to put in?
Hey John==The check engine light is trying to tell you that something iis wrong. Takeit to Auto zone and have the codes read anD it wiss tell you what area to check. GoodlucckJoe
Where is the engine number on a 2003 Ford Focus?
Stamped on the LHR of the engine block facing the radiator side at gearbox join.
Is a 1999 silverado engine the same as a 2002 silverado engine?
yes in a way but it has been modified
NEW ANSWER: The engines are not even CLOSE to being the SAME. Chevy compleaty REDISIGNED the engine blocks and transmissions in late 1999
What type of combustion engine in the steam engine?
A steam engine is an external combustion engine. As the steam engine combusts outside of the engine itself.
Are you ready for non combustion engines?
I'm very ready to go back no combustion age using another mode of transportation such as horses or by using the new solar powered energy...because the world now is getting hot.
What does the preheater in an engine do?
The preheater warms up the engine so it will start easier and in freezing weather will help to avoid freezing of the coolant.
