Dodge Durango

The founder of the band Los Horoscopos de Durango is Dn. Armando Terrazas. He found the band back in 1975. The band went on to win several Latin Grammy in recent years.

The code can only be reset by an OBD II scan tool, available at any auto parts store or local repair shop. many auto parts stores will read the codes for you and reset the light for free, Auto-Zone comes to mind. Of course, what ever is causing the light to come on will set it again in about a day. The cause must be repaired...

it is intake air temp sensor code, either the sensor is malfunctioning or unplug,

This is a software problem, not a fuse. Your Dodge Dealer has to correct the issue!

Because the air conditioner is running.

On any vehicle made since 1998 (and some made before), fault codes are read from the OBD-II port, usually below the drivers side dash, using an instrument called an OBD-II reader, or other diagnostic equipment. Some auto parts stores will read the codes out for you for free. Basic readers can be purchased from an auto parts store for about $125

no drain plug on the transmission you have to loosen the bolts on the pan.start from one corner and work your way around the transmission pan be ready alot of fluid is gona come out

open the driver door and then there is a little panal on the side of the dashboard. take it off and inside are all the fuses. then look on the otherside of the panal and it has a list of what fuses do what

Take the old one out and install a new one.

Drain, remove two hoses, if auto remove trans lines (two), remove fan guard, remove overflow container, bolts at top sides, lift out, confirm pepcock is in new one, if not use one from old unit. Install new unit,replace all above, in reversed order. Replace cap with new one. Consider a lifetime warrnity over just a one year. Fill with good coolent, run motor top off coolent, check for leaks. Recheck coolent after motor is driven and cooled. Takes about one hour.

raise the car, drain the transmission fluid, remove any exhaust components that will get in the way of the transmission, remove the starter, remove the drive shaft, remove transmission crossmember, use an engine hoist or a jack to support the engine, remove slave cylinder from bellhousing, remove transmission and bellhousing, unbolt pressure plate, inspect all components replace bad parts, reassemble. DON'T FORGET TO REFILL TRANSMISSION

there is a answer on robbietherobot.com. Edited: No there isn't. That's spam.

you can recharge the air by removing the caps make sure you use a gauge type system you can over fill and put to much pressure on the compressor but make sure you do the one that has a (L) ON IT meaning the low pressure side not the high....you can get the recharge kits at advance auto parts its easy to do. and it is a lot better than spending around $100 for a shop that's gonna do the same thing your gonna do..... 134 is what you need for this..... i would recommend the advanced brand its all the same and it will save you some $$$ esdaddy@zoominternet.net

Approx 6 quarts for filter service, up to 12 dry fill.

The 2006 GMC Sierra-1500 has rear wheel drive.

Its recommended that you remove 2/3 of brake fluid from the master cylinder to allow ease of piston compression. Loosen lug nuts. Raise truck with appropriate sized jack and support. Remove lug nuts and wheel. There are two bolts located on the back side of the caliper. Remove these bolts and grab the caliper (caliper is located in between the caliper bracket) at the top and pull back. You may also try rocking caliper by holding top and bottom. Once removed the inner and outer pads are held in place by clips. Sometimes they just fall out other times you must slide the pad outwards out of the grooves. They have special tool kits available for rental at your local parts store for resetting the piston back in or you may use a C-clamp and the old pad to push the caliper back in. Some replacement pads come with new clips and some don't. Determine which you have and replace clips if provided. They just snap on. Place the new pads in place, the inner and outer into the clips. You may purchase small packets of disc quiet that you simply spread on the BACK of the pad shim (recommended) before installing them. After pads are in place replace caliper back into bracket and guide pads around rotor. At this point you may want to lubricate your caliper pins and slides with caliper pin grease. Install bolts and torque to recommended ft-lbs. Repeat for other side. Refill master cylinder to appropriate level. Pump brakes several times to seat pads and recheck fluid level. Fill as needed.

The maximum cargo capacity of the 2003 Dodge Grand-Caravan is 167.9 cu.ft.

That depends on the engine, whether you are buying a dealer part or a generic fit aftermarket part, and what your definition of expensive is. A quality catalytic converter is not cheap.

The firing order should be 1-8-4-3-6-5-7-2.

macanic

It is on the evaporator, inside the vehicle, under the trim on the right rear.

If you are standing in front of the vehicle, I believe it is to the left of the throttle body on the rear of the intake under those plastic covers where you can`t see it.

Depending on how high you needed it to be lifted, I would try to unbolt the motor mounts and see if that gave enough clearance. Make sure there is enough room to do this all around the engine, like the intake, bellhousing, exhaust, etc.... just be sure you are not binding any wires or hoses and you should be able to lift with a jack from below of from above with a hoist. The only thing that holds the engine in the car is the motor mounts, bt again, check for clearance with other items before just lifting or jacking...

Look in the manual in your glovebox. I reset mine by accident when my fuel pump was dying. If you turn the key on 4. times without starting the truck, the computer goes into program mode. Anyway: from page 10 of the owners manual... Automatic door locks If this feature is selected your door locks will lock automatically if the speed is above 15 mph. This option is shipped activated and can be turned on and off by using the following procedure:

1. Close all of the doors.

2. Place the key in the ignition and cycle the key from the OFF position to the ON position for a total of four times ending in the ON position, do not start the engine.

3. Press the drivers side power door lock switch to lock the doors within 30 seconds.

4. You will hear a single chime when the programming is completed.

5. To activate the feature again, repeat the above steps.

...And from pages 12-13:

To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock the driver's door, or twice to unlock all doors and liftgate. The illuminated entry system will also come on. The system may be programmed to unlock all the doors, on the first press, using the following procedure:

1. Close all the doors.

2. Place the key in the ignition and turn the key between the OFF and ON position consecutively for a total of four times ending in the ON position (do not start the engine).

3. Press the driver's side power door lock switch to unlock the doors and within 30 seconds to lock the doors.

4. You will hear a single chime when programming is completed.

its not getting eough gas. check the gas lines and the fuel pump. it might be a sencer.