Dodge Intrepid

I usually pull off one end of the lower hose if the radiator petcock is hard to get at or stuck; it is usually easier and it is much faster in most cases.

Have vehicle scanned and codes cleared - usually a problem in the emission control system

It is under the housing where the lower radiator hose hooks to the engine.

The AC low pressure port on a 2000 Dodge Intrepid is located on the side of the AC accumulator. It is positioned in the left, rear area of the engine compartment.

1999 dodge intrepid is not starting I change crank and camshaft sensor and it stall will not start what can i do next.

remove the few screws you can see then lift up on the door panel. if it wont move look harder for more screws the panel should pop right up.

The wire color codes for a 1999 Dodge Intrepid with the infinity stereo are simple to follow and identify. The car radio constant 12V+ wire is pink, the radio switched 12V+ wire is red/white, the radio ground wire is a black strap, the stereo dimmer wire is orange, and the stereo antenna trigger wire is orange/red. For the front speakers, the left front speaker wire (+) is dark green, the left front speaker wire (-) brown/red, the right front speaker wire (+) is purple, and the right front speaker wire (-) is dark blue/red. For the rear speakers, the left rear speaker wire (+) is brown/yellow, the left rear speaker wire (-) is brown/light blue, the right rear speaker wire (+) is dark blue/white, and the rear right speaker wire (-) is dark blue/orange.

To jump start a 2003 Dodge Intrepid, first, ensure both vehicles are turned off. Connect the positive (red) jumper cable to the positive terminal of the dead battery, then attach the other end to the positive terminal of the working battery. Next, connect the negative (black) cable to the negative terminal of the working battery and attach the other end to a grounded metal surface on the Intrepid, away from the battery. Start the working vehicle and then attempt to start the Intrepid.

On a 1999 Dodge Intrepid, the fuel switch, also known as the inertia switch or fuel pump relay, is typically located in the engine compartment or under the dashboard. For the Intrepid, it's usually found near the fuel pump in the trunk area or under the rear seat. If you're looking for the fuel pump relay, it can be found in the fuse box located in the engine compartment. Always consult the owner's manual for the exact location and details.

To change the thermostat on a 1999 Dodge Intrepid, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, take out the old thermostat, and replace it with a new one, ensuring the new gasket is in place. Reassemble everything, refill the coolant, and reconnect the battery.

The 2002 Dodge Intrepid with a 2.7-liter engine features a DOHC design with hydraulic lifters, which means it doesn't require regular valve adjustments like some older engines. Instead, the hydraulic lifters automatically compensate for wear and maintain proper valve clearance. If there are issues with the valve train or performance, it may be necessary to inspect or replace components rather than adjust the valves themselves. Always consult the vehicle's service manual for specific maintenance recommendations.

To access the top rear strut mount on a 1997 Dodge Intrepid 3.5 ES, first, lift the rear of the vehicle and securely support it on jack stands. Remove the rear seat and any trim panels to expose the strut mount access points. Then, unbolt the strut mount from above and detach the strut assembly from the lower control arm, allowing you to replace or service the strut mount as needed. Always consult a repair manual for specific torque specifications and safety precautions.

The flasher relay for the 2001 Dodge Intrepid is typically located in the fuse box under the dashboard on the driver's side. To access it, you may need to remove a cover or panel. The relay is usually identifiable by its larger size compared to fuses, and it may be labeled in the fuse box diagram. If you're having trouble locating it, consulting the vehicle's manual can provide specific guidance.

To test the purge solenoid on a 2004 Dodge Intrepid with a 2.7L motor, first locate the solenoid, typically found near the engine bay connected to the evaporative emissions system. Disconnect the electrical connector and use a multimeter to check for continuity across the terminals; a reading indicates the solenoid is functioning. Next, apply 12 volts directly to the solenoid terminals; it should click and allow airflow if it's operating correctly. If it doesn't click or pass air, the solenoid is likely faulty and should be replaced.

To replace the O2 sensor in a 1999 Dodge Intrepid, first, ensure the vehicle is cool and disconnect the negative battery cable. Locate the O2 sensor, which is typically found in the exhaust system, either upstream (before the catalytic converter) or downstream (after the catalytic converter). Use an O2 sensor socket or a wrench to unscrew the old sensor, then install the new sensor by threading it in and tightening it securely. Finally, reconnect the battery and clear any diagnostic trouble codes if necessary.

To clean the EGR (Exhaust Gas Recirculation) valve on a 1995 Intrepid, first, disconnect the negative battery cable and remove the EGR valve from the engine. Use a suitable cleaner, such as throttle body or carburetor cleaner, to remove carbon buildup from the valve and its passages. Scrub gently with a brush if necessary, and ensure all residues are thoroughly cleaned before reassembling. Finally, reconnect the EGR valve and battery cable, and check for proper operation.