0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
What oil should you use in dodge ram cummins diesel?
Any good quality 15W40
Valvoline true-blue 15w-40
Where is the top speed sensor on a 91 lumina v6?
Never heard of a top speed sensor. Vehicles are usually governed by the computer. The only way to remove the governor is to have the computer reprogrammed.
How do you replace a fuel gauge on a 1985 Chevrolet Camaro?
Very easy, remove the bezel screws with a correct size torx screw driver, once the bezel is off, remove the trim and then the clear plastic lens. Pull the gauge out, push new guage in until it clips in, install all parts in reverse order.
Its an electronic sensor
How do you reset the airbag light on a 2004 Dodge Ram 1500?
Tisk Tisk, safety first. Don't mess with the safety features on your vehicle. This might be a life or death situation if you get in a crash. Bring it to the dealership and let the pro's figure this one out.
2002 Dodge ram 1500 pick up Why is the Lamp Out light on the dashboard on?
One or more of the tail lights, head lights, or brake lights is out.
Where is the PCV valve on dodge ram 1500?
5.7L, in the intake behind the throttle body. 3.7 and 4.7L in the side of the oil filler housing. 8.0L, doesn't have one - has an orifice system. 3.9, 5.2, 5.9L - on the top of the valve cover.
What trans does a 1999 Dodge Ram have?
the 318 (5.2L) has a Chrysler 44re transmission and the 360 (5.9L) has the Chrysler 46re transmission. The 318's also used the 46re and/or 46rh (depending on year) until Chrysler began to cheap out i believe in 1995. The Cummins diesels use the 47re transmission. all are 4 speed automatic, i don't know any of the manuel transmissions used.
Where is the cam sensor located on a 2001 Mazda protege es 20?
The cam sensor is located on the left side of the engine (as your looking at it) on the valve cover. It is the only sensor that is located on that side on the upper part of the engine.
What does the crank sensor do on Dodge Caravan?
The crank sensor is used by the ECM to determine timing. However, if the sensor is not working, the ECM determines the same things from the inputs of other sensors for timing. The net is that the sensor amounts to a redundancy, allowing the ECM to determine appropriate timing more quickly than without it.
Where is the torque converter solenoid on a 97 dodge ram 1500?
The torque converter solenoid is inside the transmission on the valve body.
The torque converter solenoid is inside the transmission on the valve body.
How do you adjust your reverse light on a 1998 dodge ram 1500?
The reverse lights are not adjustable.
The weight of a 1988 Dodge Ram 50 4x4 w/ 2.6L G54B Engine is 4655lbs (2111 Kg)
Where is the door buzzer module on a 1996 dodge ram 2500 4x4?
I own a 1994 Ram and i think it would be the same for your '96. Open your driver side door and on the side of your dash will be a removable panel, remove it and you will see a fuse block. The fuse for the buzzer, and the buzzer itself, will be in there.
How can you locate the AC drain line on a 97 VW Jetta?
On a 96, it is on the passenger side under dash and pokes through firewall.
How do you disconnect the electrical connectors on the fuel injectors?
use a small screwdriver to pry out the wire retaining clip located half way down on the plug.
If equiped with a blue plastic clip in the connector:
Pull or Pry the blue clip halfway out, using a small screwdriver or plyers. Push the tang on the side and completely remove the blue clip. Now with the blue clip removed squeeze the tang and pull the connector off.
Dunno if it's any help, but on my 93 model it was 125 INCH pounds. No sequence was listed so I criss-crossed in an alternating pattern.
What is problem when front axle won't engage but transfer case does when shifted into 4wheel drive?
there's a vacum switch on my 86 that's on the top of the transfer case between it and the floor board. that switch operates a diaphragm located on the passenger fender well near the battery in the engine compartment. that diaphragm in turn is hooked to a cable that goes to the front axle, and engages. it. your problem could be the switch on the transfer case. that was the case on mine, and I decided that it was easier to route a manual vacum pump from the cab to that diaphragm to engage the front end than it would be to try to change out that switch. not reccomending this, just offering other possiblilites.
On my 94 S10 Blazer the vacuum diaphragm is under the battery tray. You have to remove the battery and the tray to access the diaphragm.
2001 dodge ram 360----How does the timing advance when accelerating?
i have a 95 dodge ram 360 and i believe that it is vacume advanced for the distributor but then again i changed my spark plugs wires and distributor/cap and my truck started missing...???/ i have a 95 dodge ram and the same thing happened i had to rout the ignition wire over the valve cover
How do you get a belt diagram for a ram van with a 360 engine?
Any parts store ,like Autozone can print you one.
