Eagle Summit

Depends on size of truck and trailer, size of fuel tanks. But a good guest would be about 35,000 lbs.

you can't but you can pick up the trailer with the winch on a helicopter

No. A 1982 would not have airbags.

yes its pretty simple but time consuming, not a fun one but i could do it in my backyard

No special certification is required, but you do have to know what you're doing. Now if you have to replace the brake shoes (which often happens when a wheel seal goes out, as the shoes become contaminated with gear oil), you do need to be certified for THAT.

Do I need any special tools to replace front wheel bearings on a Saturn 2002 L200?Also what is the procedure for doing so?

It is under the little white ball on the front of the transmission.

There are two bolts nuts,one on each side of distributor at its base,remove and pull out,make sure you realign the new distributor with same way it came out along with the spark plug wires

It is located on the bottom of the throttle body, and the 6-pin plug faces the firewall.

Top pin is ABS. Next two pins are marker lights. Next two pins down are flashers. Bottom pin is brake lighting. Center pin is ground.

i want to download ehsaan itna sa kar de song

Infrared rays are electromagnetic waves with a wavelength longer than the wavelength of visible 'red' light [or you could say they have a lower frequency than red light]. Infrared 'light' is used in TV remote controls to transmit information to an infrared receiver on the TV, and also in security systems to create an invisible 'light beam' that when broken, will send a signal back to the system.

The speed sensor is located in the speedometer assembly, at the back of where the speedometer needle connects.

I just changed the timing belt on my 1994 Eagle summit 2.4 litre. Remove all the belts and wheels connected. Take off the covers to expose the timing belt. Your top pulley should be on the top marks aligned. The two bottom ones should point at about 10 o'clock. There should be 2 marks on the engine block. uhh the top mark(cam) might just go 90 degees to the front or level to the head gasket the no 1 piston(right drivers side) should be up to top all the way exactly and if you havnt moved your distributor ( dont ) it should start outher wise the distributor rotor would be faceing down with the rest of the marks as discribed ok?

If your Eagle still has the Diagram sticker on the underside of the hood, this should explain exactly where the transmission dipstick is located. For the purpose of disclsure, it is a smal,l ususally white, plastic ball about a half inch in diameter on the lower left of the transmission as viewed from the engine compartment. Yo need to reach down to the left. The white plastic ball looks like a plug rather than a traditional ringed dipstick handle. Theres the confusion. This is a bit of a bugger when the engine is hot and or running. CAUTION!

Yes it does.. Just replaced my brother's head on his.

Yes.

You can remove the distibutor, by locating it on the left-side of the engine block, remove the cap by two screws on either side, remove the two wiring harnesses and a possible third wire held on by a 10mm bolt. Then remove the two 12mm, bolts or nuts(depending on which model you have). the distributor should just pull out, some are easier to pull out than others, which may need just a little pry to get them loose.

i have no idea

check ur fuse box, my friend didnt have any heat so he checked his fuse box and he didnt have any fuses, so maybe check that

it is directly on top of the compressor underneath the distributor cap

more the likely the distributor but check easy things 1st cap rotor ect...

i know i own one too!ive replaced mine 2 times in 4 years!

to change the starter locate the transmission bell howsing the starter will be located behind the motoer close to the tranny you will need to disk connect the battery, remove two bolts and slide out the starter remember which wires were conected to which terminal and insert the new starter reconnect the wires in order of which you took them off then tighten on the bolts

The fuel pump is located in the fuel tank. Just replaced it twice on a LX model. Manuals I have gotten on this car are incomplete and contain wrong info as well.The most informative manual so far is Mitchell's. If you can find the Chrysler manual I would suggest getting it.Here's how i changed it. Jack up right side of car , remove wheel , there is a drain plug to empty the tank if you wish to do so, disconnect two rubber lines that are clamped with circular metal clamps, remaining hose is supply line and requires two wrenches to uncouple. Four nuts hold the tank up to the frame lossen and remove the nuts while supporting the tank . Drop the the tank while making sure the fuel quantity sending wires are not stretched or broken and as the tank drops further the fuel pump power wires. when tank is on ground or dropped far enough you can disconnect the wire plugs for the sending unit and pump. When all that is accomplished the tank can be moved to a location where it is easier to work the pump removal task. Please read and follow all warnings about working the gas system. especially disconnecting the battery. Have fun

80,000 lbs