0
Ford Probe
The Ford Probe was a compact sports car manufactured by Ford from 1989 to 1997. It was completely based on the Mazda G-platform using unique interior and sheet metal. The car was sold in both North American and European markets.
1,060 Questions
What are the precedures for replacing the alternator on a 1993 ford probe gt?
It's kinda of a rough job to do it cuz the alternator is placed at an odd spot. You can get at it from the top but you'd have to take the rad out. If you want , get the car on a hoist and go from under but the a/c compressor would have to be moved.
What is a cause for the manual shift light flashing on a 1991 ford probe?
This generally indicates an electrical failure in the transmission. Get it fixed now, or you'll end up replacing it.
Can you use 10w-30 motor oil on your hybrid?
Use exactly what the manufacture recommends and nothing else.
What causes the car battery to drain on a 93 Ford Probe?
this answer should help its from a similar question i answered What_could_be_causing_your_2000_ford_windstar_battery_to_not_hold_a_charge
Will a 1989 ford probe transmission out of the 4cly fit the 1990 probe v6 both being a 5 speed?
i think that it might work
93 ford probe fuel shut off light staying on?
it is a trouble code, get an OBD reader and u can turn it off. or your fuel cut off switch (located in the trunk) could be bad.
How do you remove a CV axle on a 93 Ford Probe?
It really isn't hard but you need direction. Get a manual on your car from AUTOBOOKSONLINE.COM
Jack up the car and place jack stands under a solid area Peen the safety lock on the axle nut with a hammer an chiesel Remove the axle nut with a strong impact gun and a 1 1/4" socket Remove the brake caliper & hang it with a tie wrap Remove the brake shoe housing Remove tie rod from spindle Remove the ABS wire harness clip in strut Remove the 2 strut bolts with a 17mm socket and wrenches Remove lower ball joint locking bolt Swing down spindle assembly and remove axle assembly from outer splines Knock out axe from transmission side
Note: If axle is seized in hub, spindle assemble must be removed with axle attached and then heated and removed.
The oil pump turns more at higher revs, this is then producing more oil pressure, so when you change gear the revs are in a lower range so the oil pressure drops.
Would a mustang 302 clutch work on a probe 93 gt Could you switch it out and would it just fit.?
I highly doubt that it will. The 93 probe GT is a Mazda car with ford body on it. It is the same as the Mazda mx-6. this goes for years 93-97
Answermy 92 lx with the 3.0 is built by Mazda for ford too, so i think that jap heritage runs deeper than most of us know (or admit)A probe is a tool that is inserted into something to view or get information abour what is going on inside that object.
A satellite that goes into deep space is an example of a probe.
Why does ODOFF light come on and car slip out of gear or down shift violently?
your tranny is going out sorry to say same thing happen to me get it check can be costy if dont get it looked at to soon look into spending 1200+ for a new one with labor to get it put in your gears are slipping
How do you bleed air from a power steering pump in a 1993 ford probe?
put an air compressor hose on one end
How do you change front turn signal lights on a 93 ford probe?
2. Turn the bulb holder counterclockwise and pull it out of the housing.
3. Pull the bulb from the holder and replace.
What could be the problem if your car sputters when you press the gas?
Could be several things... O2 Sensor, fuel issue etc. Most of the time you will find that it's simply the car's computer needs to be reset (due to dead battery or having the battery unhooked for a few minutes.
Heres a quick way to reset the car's computer;
make sure the car is warmed up
pop the hood and unhook the negative battery terminal
make sure that the terminals are not corroded, if so you need to clean them first (i use baking soda and water but most just use a wire brush)
with the negative unhooked, get in your car and press the brake pedal and hold for about a minute
get back out of the car and reconnect the negative terminal
start the car and let it idle for about 5 minutes
Drive the car around. be easy on it at first, because the car will sputter a little bit more than likely. The car is resetting several things, like the airflow detection etc.
If that doesnt help, then you probably need to try cleaing out the Mass Airflow Sensor (MAF)
Google that
How do you install a new gasket seal?
we need to know which gasket your talking about. Gasket in a condesate pump
Is a 93 Ford Probe transmission compatible to a 95 Ford Probe?
i belive it is but just check the model number on the tranny and make sure they match just incase im wrong
yes so it the entire engine assembly
Where is the PCV valve in a 89 Ford Probe?
On the 4 cylinder models, it is on the passenger side of the valve cover.
Where is the reset fuel cut off switch in 1994 ford probe 2.0?
in the trunk, under the carpet to the left side quarterpanel
How much transmission fluid for a 1992 automatic Ford Probe?
The quantity of transmission oil is 9.6 liters. It is important that Mercon oil is used, not Dexron or any other type.
How do you replace the ignition switch on 1990 Ford Probe gt?
If You have a local locksmith check with him you will find that they do this type of work and most of the time a lot cheaper then the dealers. If you get a new igniton they also can re-key to your existing key so you dont have a key for ignition and another one or two keys for door trunk and glove compartment. If You have a local locksmith check with him you will find that they do this type of work and most of the time a lot cheaper then the dealers. If you get a new igniton they also can re-key to your existing key so you dont have a key for ignition and another one or two keys for door trunk and glove compartment.
