answersLogoWhite

0

Honda Accord DX

The Honda Accord DX was a four-door sedan powered by a 2.3L I4 engine that delivers 135HP. It was a value-oriented trim offering a value-package that included air conditioning and a radio-cassette player. The model was available in front-wheel drive layout.

823 Questions

How do you put the alternator belt on a Honda Accord DX?

you start by loosening the tension pulley that's actually hooked to the alternator(right off the top bolt), once this is loosened, you can move the alternator back to where the belt fits and tighten it back up and your done

How do you remove a headlight cover on a 1995 Honda Accord?

The headlight is an assembly. To replace the headlight, you remove the bulb from the back side. It is a halogen bulb, so do not touch with bare hards before installing.

How do you check the transmission fluid in a 2003 grand am through the check plug since they do not have dipsticks?

AnswerThe transmission needs to be at operating temperature. With the engine running and in park, remove the plug. it is located under the car, near where the right axle comes out of the tranny. Remove the plug and the fluid should be level with the hole, so add fluid till it comes out. This should be done on a hoist. If you do it in the driveway, you are probly using jack stands and the car wont be level, so you will over fill it, not good.

How much amps does a 1994 Accord DX sedan alternator have?

tag on alternator, but probably 35 amps >>CORRECTION>> adding "alternator" to the question is correct, however the amperage rating for an alternator in a 94 Accord DX is 80 amps. Unless of course this DX model has a VTEC engine (very unlikely) then it will have a 90 amp alternator installed.

What does it mean when you step on the breaks of a 91 Honda accord and the car starts to shake?

AnswerMy car had a problem like that also, I changed the front brake rotors and the problem went away.

If replacing the brake pads and rotors does not solve the problem, you may have an issue with one or both of your calipers. Often calipers can sieze partially or completely. This will make the brake distribution uneven between the front wheels and can lead to shaking or pulsing when applying the brakes.

Where is the expansion valve located on a 1998 dodge ram 5.2 L?

The ac system on a Ram doesn't use an expansion valve. It uses a fixed orifice system.

Check coolant level?

To check the coolant level of a vehicle first see look for the overflow reservoir. There should be a coolant dipstick with a level gauge on it. Remove it from the reservoir to see the coolant level.

Where are the fuses on a 99 Honda Accord?

There are three different fuse locations, what fuse specifically?

My 1994 Honda Accord's blower comes on only after hitting a bump Is it the relay or needs replacement?

Blower is about to die. I had same symptoms. Blower would not come on so I would run over bumps then it would engage. Replace blower no problems since.

Ignition timing for 1990 ford bronco 351 winser?

the firing order on a 1990 ford 351 windsor is *1-3-7-2-6-5-4-8* number one cylinder is front left looking from front of vehicle and distributor spins counterclockwise ,, if the distributor has been pulled and restabbed but motor never moved without dist it wont be bad but if u cranked it while dist out then u gotta go text book, set and pull number one cylnder and align to tdc ,, set to front passenger side (#1) cylinder and stab from there ,, it might take a while but it can be done ,,, GOOD LUCK ---JAMES

How do you check the transmission fluid on a 2002 Rodeo?

Transmission fluid level: As you don’t have an ATF dipstick, you will have two plugs facing downward on the larger trans pan. The plug higher up on the pan is the fill/level check (stamped/recessed into the rear right corner of pan). ATF should just dribble from this plug on a hot, idling truck, in neutral on a level surface. The lower one is the drain. The one at the back of the pan in a recess is the filler. You need a hand pump or something similar to fill it to overflowing then top it off with the engine running. Make sure you shift through the gears a couple of times when topping off.

Which one is the cooling fan motor on a 2000 Honda Accord?

get in the car when it is cold, turn on the ac, then check under the hood. the fan that is not spinning when the car is cold is the cooling fan

What is the location of the o2 sensor in a 96 Honda accord?

The location of a o2 sensor on a 1996 Honda Accord is on the exhaust pipe. These parts help regulate the emissions for the vehicle and are placed on the down pipe of the exhaust system.

Why does your 1998 Honda Accord Automatic stick shift stick in park?

When the car is turned off, it is best functional to be parked if it stays in parked..however, i do believe it is possible to shift it into another gear by putting the key in a slot that's beside the stick-shift (however this may not be in all accords.) If you do this, i highly recommend u don't leave the car parked in neutral..this can cause the car to roll forwards/backwards since neutral means the car isn't in gear.

Where is the 1995 accord clutch pedal switch?

A 1995 Honda Accord clutch pedal switch is located directly under the clutch pedal. This switch stops the car from starting with depressing the clutch. This helps avoid accidents.

How do you remove the alternator from the engine capartment from a 87' Honda Accord DX. It seem as there is no way to do this without removing engine?

*Remove the negative battery connection!
*Raise the right side of the car and place it on a stand and remove the front tire.
*Remove the air cleaner (and several hoses, one electrical connection).
*Remove 3 vacumn components (box looking thing and two round what-ya-ma-call-ems) and several more vacumn lines from the right side of the engine compartment.
*There is one hose connecting from the engine block to the intake manifold that is has coolant flow in it. It was in my way and and I disconnected the manifold end of that hose. Lost a little coolant on the ground. Nothing major.
*Remove the upper bracket that are holding and tensioning the anternator.
*Remove the belt.
*Remove the anternator lower bolt. I also removed the lower bracket, I'm not sure I really needed to though.
*Turn the back end of the alternature up and disconnect the wires.
*Lift the pulley end out through the space made by disconnecting the vacumn stuff.
*When it seems to be stuck, roll the alternater about 90 degrees and keep lifting. *Tight, but IT FITS through.
*Place the new one back down the same way. Connect the wires then bolt into place.
Good luck! You have to pull the driver's side axel. --------------------------------------------------------------------------------------------------------------------- A lot of Honda engine repairs are done through wheel well. Y-THINK-Y