0
Honda Accord EX
Introduced in 1984 with a 1.8 liter engine, Honda Accord EX was marketed in New Zealand, Australia, Canada, and the US. The EX replaced the LX-I and SE-I models during the 1990s.
5,157 Questions
How do you remove the distributor rotor on a 1999 Honda CR-V?
Follow this link: http://www.digmyhonda.com/h/story.php?title=DIY_distributor_CAP__ROTOR_replacement
With the cap removed for observation, put the vehicle in second gear, take the hand-break off, and bump/jerk the vehicle forward until rotor arm rotates and screw is exposed. It will be exposed pointing inward/backward toward the cabin and should be a Posi-drive™/Phillips™ screw/bolt. Have the ignition off while bumping the vehicle. -=bc=-
What is 1992 accord minimum brake rotor thickness front and back?
The minimum brake rotor thickness for the front and back rotors on a 1992 Honda Accord is 21mm. Rotors which are below this thickness will not offer adequate or reliable braking.
What type of oil is best for a 1997 Mercedes E420?
It is important to use the right type of fluids in a vehicle so it runs smoothly. A 1997 Mercedes E420 uses 10w-40 engine oil.
Does a 2004 Honda accord 4 cylinder have a timing chain?
Yes, the 4 cylinder has a cam chain but the V6 has a cam belt.
How do you replace the air filter and cabin air filter in a 2002 QX4?
notes: i replaced my filters when purchased the vehicle at 65k miles. they were nasty. be prepared to clean a bit. i replace my filters every couple years.
the operation takes about 45 minutes for amateur like me, assuming there have been no significant changes in filter location & design or dash design since 2000 model:
1) purchase new filters. there should be 2 hepafilters per package. they're approx 4"X8" and quite pricey. you'll also need the following tools: Phillips & flat blade screwdrivers, pliers, vice grip pliers, flashlight, approx 12" length of coat hangar wire (optional), shopvac with needlenose attachment (optional), can of lysol (optional), ballpoint pen (optional).
2) empty and remove glove box - located two sliding pivots at bottom and outside of glove box door. slide the 2 plastic latches inward and pull the glove box toward you a few inches. locate the cable eye that attaches the glove box door to the counterweight. have the vice grips ready to clamp onto the cable that holds the counterweight, then remove the eye from the peg on the glove box door.
3) use Phillips screwdriver to carefully back out the plastic screws in the right side kick panel. you may have to remove one or two screws from the carpet edging in doorway.
4) looking at the side of the heater box, locate the vertical edges of the filters. the filters are held in place with a metal clip at bottom. its been awhile since I've replaced these - there may be one at the top, as well. use flat blade screwdriver/pliers to carefully remove the clips and keep them handy, as they'll be reused.
5) pull out the bottom filter first, then slide the top one down and pull it straight out. you may want to lay down a piece of cardboard or paper towels, these can be quite nasty. match the old filters to the new ones to ensure you have the right ones. if so, dispose of the old ones. this exposes the heater core, which is quite fragile. its also expensive and a real pain to replace, so be careful.
6) using pliers, bend a 90-degree angle in the coat hangar wire, about 1" from the end. using the flashlight to aim, CAREFULLY clean the slot at the bottom of the air box. use the shopvac needlenose attachment to clean out any filtrate that has been left in the airbox. you can use the lysol at this point to spray down that area of the air box, which is a haven for mold and mildew in humid climes.
7) open the bag with new filters and note how the edges fit one upon the other. note that one can slip in along the edge of the other. that's how you will need to install them. slide in the upper one first and hold it at the top of the slot with one hand while sliding in the second (bottom one). replace the clamp. if desired, use ball point pen to note date and mileage on the decal supplied with new filters. peel and stick the decal to the edge of the filter.
8) replace other parts in reverse order.
Good luck!
-j
notes: i replaced my filters when purchased the vehicle at 65k miles. they were nasty. be prepared to clean a bit. i replace my filters every couple years.
the operation takes about 45 minutes for amateur like me, assuming there have been no significant changes in filter location & design or dash design since 2000 model:
1) purchase new filters. there should be 2 hepafilters per package. they're approx 4"X8" and quite pricey. you'll also need the following tools: Phillips & flat blade screwdrivers, pliers, vice grip pliers, flashlight, approx 12" length of coat hangar wire (optional), shopvac with needlenose attachment (optional), can of lysol (optional), ballpoint pen (optional).
2) empty and remove glove box - located two sliding pivots at bottom and outside of glove box door. slide the 2 plastic latches inward and pull the glove box toward you a few inches. locate the cable eye that attaches the glove box door to the counterweight. have the vice grips ready to clamp onto the cable that holds the counterweight, then remove the eye from the peg on the glove box door.
3) use Phillips screwdriver to carefully back out the plastic screws in the right side kick panel. you may have to remove one or two screws from the carpet edging in doorway.
4) looking at the side of the heater box, locate the vertical edges of the filters. the filters are held in place with a metal clip at bottom. its been awhile since I've replaced these - there may be one at the top, as well. use flat blade screwdriver/pliers to carefully remove the clips and keep them handy, as they'll be reused.
5) pull out the bottom filter first, then slide the top one down and pull it straight out. you may want to lay down a piece of cardboard or paper towels, these can be quite nasty. match the old filters to the new ones to ensure you have the right ones. if so, dispose of the old ones. this exposes the heater core, which is quite fragile. its also expensive and a real pain to replace, so be careful.
6) using pliers, bend a 90-degree angle in the coat hangar wire, about 1" from the end. using the flashlight to aim, CAREFULLY clean the slot at the bottom of the air box. use the shopvac needlenose attachment to clean out any filtrate that has been left in the airbox. you can use the lysol at this point to spray down that area of the air box, which is a haven for mold and mildew in humid climes.
7) open the bag with new filters and note how the edges fit one upon the other. note that one can slip in along the edge of the other. that's how you will need to install them. slide in the upper one first and hold it at the top of the slot with one hand while sliding in the second (bottom one). replace the clamp. if desired, use ball point pen to note date and mileage on the decal supplied with new filters. peel and stick the decal to the edge of the filter.
8) replace other parts in reverse order.
Good luck!
-j
What size are the stock rear speakers in a 1991 Chevy lumina?
The size of the stock rear speakers in a 1991 Chevy are 6"x9". You can go to crutchfield.com for any other car stereo needs, just provide the site with some information on your car's year, make, and model, and body. From there they will provide you with the correct speakers that will fit your car. I hope that has helped!
How do you change cabin filter for Honda accord 2004?
No pictures but the filter change is very simple. I just completed the replacement on my 2004 Accord V6.
First locate components to be removed.
Look on the right side of open glovebox and locate a plastic lever. You will see groves on the end connected to the glovebox. The groved area is the spot to place the thumb in order to press this lever off the glovebox.
Lay on the floor on the passenger side and look up under the glovebox. You will see two brass colored screws one on each side of the glovebox. these screws go up through two square plastic hinges attached to the glovebox and in the the dash frame.
With the glovebox closed remove the two brass colored screws and lay them in the floor.
Open the glovebox and hold the glovebox with your left hand and press on the plastic lever located on the right side of the glovebox. This lever is slotted and will pop off the glovebox.
Lay glovebox in the driver seat.
Look straight in behind the glovebox. You will see a rectangular black plastic cover approximately 1.5 inches wide by 8 inches long. On the right and left side are arrows pointing in. Press the arrows and pull out on the cover. This will slide out the tray that holds the filter. Remove old filter and insert the new one, flow arrows pointing down.
Retrieve glovebox hold in place and attach plastic plastic lever to the right side of the glovebox. The reverse of removal.
NOTE -The two plastic hinges located on the bottom of the glovebox fit underneath the dash frame.
While holding the glovebox in place (the glovebox latch may hold glovebox in place while installing screws) re-install the two brass colored screws through the plastic hinges into the frame and tighten.
Filter Replacement Complete.
Where is the egr valve on Honda civic 2000?
The EGR Valve is locaded right on the back of the manifold on the left side is the one that looks like is mostly glued not screwed.....
What is the order of the spark plug wires for 1996 Honda accord?
Click the link and choose the correct engine.
How do you change a 95 Honda Accord ex water pump and timing belt?
need help on changing 95 Honda accord ex water pump and timing belt.
Does a 2003 Honda cr-v 4-cylinder have a timing chain or?
Belt - replacement recommendation is 105,000 miles.
If you have a 2.4L 4cyl, then it should be a chain.
If the vehicle has less than 75,000 miles on it, use 10W-30 weight. If more than 75,000 miles, use 10w-40. These are multiweight oils, which means the viscosity when cold will be 10, and when hot, either 30 or 40.
How do you replace the spark plugs on a 2002 Mitsubishi Montero sport xls 3.5lt?
Replacing spark plugs is pretty simple. Disconnect the battery, remove the cover and cables, remove the old spark plugs, put in the new spark plugs, put the cover and wires back on the spark plugs, and reconnect the battery.
Where is the trip reset on Honda Accord?
The dial you use to adjust the dash light brightness. Push and hold it in and the trip odometer will reset to 0.
How do you reset service light in 2003 Honda Pilot?
How do you reset service light in 2003honda pilot
What is the difference between Honda accord lx and ex engine?
about 5 HP one is Vtec and the other isn't the LX is a 2.0 litter and the EX is a 2.2
How do you replace a starter on a 1989 Honda accord lxi?
Disconnect the battery. There's two bolts one on the bottom is hard to reach, the one on top is not too bad, and one wire. have some good tools or your hands will hurt. whne you put new one in make sure you dont ram it in there. Think of it as slow sex.
Where is the AC compressor on a 1991 Honda accord?
If you are facing the front of the vehicle the AC compressor is located on the right side of the engine, below the alternator.
