0
Honda CRX
The Honda CR-X, formerly the Honda Ballade Sports CR-X in Japan, was a small sports car built by Honda. Re-launched in 1988 and manufactured until 1991, the CRX became popular for its performance, good fuel economy and quick handling.
595 Questions
I highly doubt it. You would need to make mad modification to it if you would want to do so.
What oil do you use in the 1990 Honda CRX transmission?
For a manual transmission, just plain ol' motor oil; shop manual says SAE 10W-30 or 10W-40 oil rated SE or SF...
Where are the turn signal flasher and emergency flasher located on a 1988 CRX SI?
located on fuse box under dash
Why won't your 1995 Ford Aspire start?
Additional answer
You're not being very specific. Your engine may not turn over, or it may not fire (two different symptoms). Which is it? And if it turns over, will it sometimes fire, or never?
How do you remove the rear view mirror on a crx?
there should be a little "cap" if you follow it from the rear view mirror and up to the top and it should be 2 or 3 Phillips head screws and that should be it
It is a 1.8 liter motor that you really want for your CRX to replace the 1.6 liter that came with it. You will go faster with the B18 swap.
What if your 92 Seville won't start?
Start trying to isolate the problem. Find out whether it's getting fuel and spark. Narrow it down a little at a time until you find the problem, THEN replace the part. Don't just throw parts at it.
How do you replace the thermostat located on a 1989 Honda CRX?
Youve just redone the thermostat
Just a note: I had a buddy who wanted to help. so he tightened the thermostat housing and cracked it. the torque specs for my '90 was 13 ft/lbs or so. It should be around the same for the 89. Just don't reef on the housing bolts.
How do you replace the master cylinder on a 1990 Honda CRX?
Hello,
Here is a simple walk-through on replacing the master cylinder on a '90 CRX:
Disconnect the negative battery cable and disable the SRS system (if equipped.) At the top of the clutch pedal, remove the cotter pin and pull the pedal pin out of the yoke.
Remove the nuts and bolts holding the clutch master cylinder and remove the cylinder from the engine compartment.
Disconnect and plug the hydraulic lines from the master cylinder.
Installation is the reverse of the removal procedure. Bleed the clutch hydraulic system.
How do you replace the license plate bulb on a 2004 Honda cr-v?
how to replace the license plate bulb on a 2004 Honda cr-v
Is Honda 89 crx 1.6 dohc engine interference?
yes it is, if you broke the timing belt there is about a 90% chance you bent a valve
Does a Honda crx have clutch fluid?
The Honda CRX features a cable type clutch and therefore does not have fluid. The CRX Del Sol however features a hydraulic assembly and does.
Will a 1988 Honda CRX motor fit a 1987 crx?
Yes with a little bit of you work. go to Honda-tech.com you can find every thing you want to no there.
Where is the main relay Honda CRX del sol?
Under the dash, drivers side by the fuses. Held on by screw?
Does it ruin the engine if a timing belt breaks while driving a 1988 Honda CRX si?
Yes, It will. HF and the Si versions are interference type motors! It won't kill your entire engine but you will have too rebuild the head because of the bent valves!!!
How do you know if a head gasket is blown on a 1991 Chevy cavalier?
check engine oil for water and check radiator for oil
What is the correct 1991 Crx head torque specification and sequence?
hondahookup.com has manuals u can download with the info u need
Can you put a Honda type r engine in a Honda CRX?
Yes they are fairly easy to bolt in with the required parts and knowledge.
If you research enough online then you will find out it is not too hard.
How are crx si engine cylinder sleeves removed?
To remove the cylinder sleeves from a CRX Si engine, first, the engine must be disassembled, including removing the cylinder head and other components. Once access to the cylinders is achieved, the sleeves can be pulled out using a sleeve puller or a similar tool, applying even pressure to avoid damage. It's important to heat the block gently to expand the metal, which may help in loosening the sleeves. Finally, ensure all surfaces are clean and free of debris before installing new sleeves.
