0
Mercury Villager
The Villager was a minivan manufactured by Ford Motor Company from 1993 to 2002, and was a rebadged version of the Nissan Quest. Designed by Moray Callum, the Villager featured a five-speed automatic transmission and a front engine, front-wheel drive layout.
1,605 Questions
Where is the ignition coil on a 2000 mercury villager?
If your car has an external coil, it will be bolted to the engine near the distributor. Otherwise, it is inside the distributor housing.
Where is the 1999 Mercury Villager jack?
It's in a storage bag attached to the underside of the third row bech seat.
Where is the fuse for the fuel button release?
On my 1999 De Ville it is in the trunk on the left hand side. Pull back the covering on the back wall.
Where is the rear air control unit on a Mercury Villager?
if it is equipped from factory it is mounted by the rear controls for the radio behind drivers seat
How do you change rear wiper in 93 Mercury Villager Van?
1. Detach the small hose/line carrying washer fluid from the nozzle on the hatch door 2. pull the wiper arm from the axel of the motor, remove the wiper (if it is rusty, use flat head screw drive to remove) 3. Insert the wiper into new arm 4. Press the new wiper arm onto the wiper motor axel 5. connect the hose/line to the nozzle
What is the spark plug gap on a 94 villager?
Listed in your owner's manual and under the hood on a placard.
Where is the speed sensor on a 1996 Mercury Villager?
The Vehicle Speed Sensor on the 1996 Mercury Villager is located on the back of the transmission (as you look at the vehicle from the front) on top of the transmission with a pair of wires leading away from it... best to reach it from under the vehicle.
Where is the timing belt marks for 1995 mercury villager 3.0 v6?
The marks are on the pulleys and on the belt itself.
Where is the alternator located on a 1999 mercury villager sport----- bottom of engine?
It's mounted low and to the rear (right side) of engine. You need to remove the splash shield and access it from under the car.
How do you remove the alternator from a 1995 mercury villager?
Remove the right wheel, then get down underneath it, remove the splash shield, back off the adjuster, remove the belt, and unbolt it.
Where is the heater core in 1999 Mercury Villager 2001?
In the lower part of the dashboard on the passenger side.
Where is the rear blower motor relay on a 1996 Mercury Villager?
The Rear Blower Motor Relay is located near the rear wiper amplifier, behind the rear LH quarter trim panel.
NOTE: Ford does not provide a picture location of the Rear Blower Motor Relay. Ford only provides a written location and an image (see below) that shows the general area that the Relay is in. Full Body View
Where is the alternator located in a 1995 mercury villager?
The alternator is mounted down low on the back side of the engine.
Where is the high beam relay on a mercury villager?
Depends upon the year, but on my 1994, there are separate relays for left and right headlamps. Both are located under the hood in a clearly marked panel. One panel is located right behind the radiator and one is located on the inner fender wall on the passenger side (I believe).
Where is the outside temperature sensor located on a 2000 Mercury Villager?
In the engine compartment
What are the timing belt marks for a mercury mystique 1998?
need a special tool to lock in the cams. lock key sits at the twelve o'clock position.
Where is the knock sensor located on a 2000 Mercury Villager and is it easy to change?
you will have to remove intake and you will see it underneath two coolant lines. can be done. time cosuming and a lot to take apart. ON THE ENGINE HEAD AND IT IS VERY HARD TO BE CHANGED.
I changed the knock sensor should I change the lower manifold gaskets too?
It is not necessary to change those gaskets if all you have done is change the knock sensor. If they seem to be worn then you probably should go ahead and install new ones.
What is the Firing order on 97 Villager 3.0?
from top (left to right): 1 3 5 from bottom (left to right) 2 4 6
How can you tell if your 2000 mercury villager is turning over with a broken timing belt?
DO NOT ATTEMPT TO TURN THE ENGINE OVER IF YOU SUSPECT A BROKEN TIMING BELT !!!!!! If you have, you already have more problems than a broken timing belt. Remove the upper timing belt cover and physically look at the timing belt.
Where is the camshaft position sensor located on a 1999 Mercury Villager?
Cam position is taken from the distributor on this vehicle, there is no separate cam sensor.
How do you install front brakes on a 1995 Mercury Villager?
Standard brake removal and installation.
Tools required: Jack and jack stands Tire iron Socket set with 'Torx' or 'star-drive' bits. Screwdrivers C-Clamp (or something to push the caliper back in) band-aids and neosporin.
Procedure overview: Remove cap from brake fluid reservoir, block rear tires, loosen (but don't remove) lug nuts, jack up the car and place jack stands for safety (you don't want 3,000+ lbs. of van landing on you). Remove lug nuts and wheels. Remove the caliper mounting bolts and detach the caliper from the steering knuckle. Use C-clamp to push the piston into the caliper. Use a screwdriver to remove the old pads. Installation is the reverse of removal. When done, step on the brake pedal a few times, and check brake fluid level, filling as necessary.
Is the mercury villager a good van to buy?
Absolutely! With it's Nissan drive train you can expect to get 300,000 miles or more if this vehicle is properly maintained. I am on my 3rd one and enjoying the great gas mileage and comfort this respectable van provides. It is a surprisingly heavy van and very comfortable especially on long trips. I'd buy another one tomorrow. I don't know why Ford/Mercury stopped making this beautiful machine, a big mistake on their part.
