0
Saturn S-Series
The first series of Saturn cars, the Saturn S-Series was part of a compact car family produced between 1991 and 2002. It was available in sports coupe, sedan level and sedan wagon variants, with either 4-speed automatic or 5-speed manual transmissions.
2,389 Questions
How do you replace the hydraulic lifters on a 96 Saturn SL?
how to replace lifter saturn 2002 1.9l sohc
Will a temperature sensor cause bad idling in a 1999 Saturn?
It can, but you should trust the computer diagnostics in a situation like that.
Where is the coolant temp sensor on a 1993 Saturn sc2?
Your Saturn Twin cam engine actually has two temp sensors on it. They are both located on the right side of the cylinder head ( right side as if you are looking at the motor) mounted just under the valve cover line. They are small 2 wire pinch type connectors and are simple to replace. The one closest to the water inlet is the sensor that controls your gauge on the dashboard. the 2nd sensor just behind that controls the computer and your engine fans.
Car ceiling interior is falling down How can I glue it back up?
Use Spray glue that are for fabric,cardboard, etc.....
What is a 2001 Saturn SL2 matainence schedule?
OIl and filter - 3k
Spark plugs - 30K
Tranny fluid and filter (auto) 15k
Belt - check every oil change
tires - check every other oil change
Where is the egr valve pressure sensor on a 2001 Saturn sl2?
There is no pressure sensor. The EGR valve is located on the head next to the battery. Cleaning it is usuallu the first step if there are any SES codes associated with the valve.
Where do you drain transmission fluid from a 1999 Saturn SL2?
From under the tranny. Youll see one odd size bolt that is the drain. On manuals its on the differential bottom. On auto's its on the bottom of the tranny. Autos have filters on the front side of the tranny. manuals have NO filters
The most likely culprit is the Transmission Valve Body. The reverse valve wears out the aluminum housing and when warmed up, causes the fluid to flow around it instead of pushing it. If you can rev the engine up and get it to go into reverse then that is most likely it. There is an aftermarket company called Sonnax that makes repair kits for transmissions but don't look to put the kit in yourself. The kit can be had for $19.95 but the special reaming tool is around $500.00. Look for a rebuilt valve body with the Sonnax kit and install it. They can be had on eBay for as little as $175.00. Installation is relatively easy for someone with the know how and the tools. It took me less than an hour to do mine. One caveat: read the directions that come with it! There are steps that need to be taken to reprogram the car's on board computer system. If you skip these steps, you will think that the rebuilt valve body is badly defective as the transmission will not want to go into gear and when it does, will shift very harshly. The computer has to learn the new valve body's hydraulic requirements and you have to initiate this process.
Yes, you should check all of the rims and while you're at it, recheck the one that was just replaced. You might also have a bent axle shaft. Check that the new wheel was balanced when installed. Check alignment and other front end parts for possible damage if the curb strike was very hard. You may have also damaged your hub assembly when you hit the curb
How do you remove the timing chain cover on a 3L 1995 Aerostar?
Disconnect the negative battery cable. Turn the crankshaft until the No. 1 cylinder is at TDC on the compression stroke with the timing marks aligned. Remove the idler pulley and bracket assembly. Remove the drive and accessory belts. Remove the radiator and water pump Remove the crankshaft pulley and damper Remove the lower radiator hose. Remove the oil pan-to-timing cover bolts. Remove the front cover bolts and the front cover. Tap the cover lightly with a plastic mallet, if necessary, to break it loose.
This is caused by your PCM being unable to adapt enough to correct a problem in the fuel/air mixture. This can be caused by several things, not necessarily in this order. Catalyst plugged Bad Powertrain Control Module Engine parts tolerance Fuel injector(s) stuck open or leaking MAP sensor O2 sensor (upstream) Fuel pressure regulator Wiring harness/connector problem
How do you remove a house door handle?
In order to remove a house door handle, you will need to take a screwdriver and remove the screws from the exterior of the door. Once the screws are removed, the handle should simply pop out.
How do you you flush a power steering system in a 2007 Saturn SW2?
There is really no reason to need to flush your powersteering fluid unless it has been contaminated. Saturn has no procedure for flushing your powersteering system. If your system has been contaminated, you can manually change the fluid, easiest way is to use a suction gun and empty the powersteering reservoir. Refill the reservior until full. start the engine and allow it to idle for a few minuites. repeat as needed until the fluid is clean.
Why will your 2002 Saturn sc2 not shift out of park?
There SHOULD be a switch on the brake pedal that disengages the gear shift locking solenoid. Once you press on the brake pedal, the gear shift should move easily. If not, either the switch or solenoid has failed, or one of them is out of adjustment.
Where is ls400 Coolant Temperature Sensor?
The engine temperature sensor on a 89 - 97 ls400 with the 1uzfe 4.0L V8 Quad Cam can be found at the front of the intake manifold behind the upper coil and behind the black plastic bridge that houses the spark plug leads. There are actually two(2) of them and are either green or grey in colour and are for the E.C.U. and the temperature gauge respectively. The green one tells the computer what temperature the engine is at and adjusts the fuel-air ratio accordingly.
What is procedure for oil pan gasket replacement on a 97 Saturn?
drain the oil from the vehicle, unbolt the oil pan, scrape old gasket from pan and crankcase. check the torque specifications for the oil pan bolts (shouldnt be very high). replace the gasket and oil pan to factory torque specs. put drain plug back in and fill with factory specs of oil.
What parts do I need to do a tune up on your 2000 Saturn LS1?
It's more an issue of how long it's been since certain items have been replaced.
- For the V6, you'll need to replace the timing belt every 100,000 miles. For the 4 cylinder, don't worry about it, it has a timing chain.
- Oxygen sensor as needed, usually around 60,000 to 80,000 miles.
- Spark plugs according to the schedule described in the owners manual.
- Fuel filter according to the schedule.
- Spark plugs and wires according to the schedule.
- EGR valve as needed.
- Air filter according to the schedule.
- Oil change and oil filter according to the schedule.
There is no distributor, rotor or points to deal with.
What would Make a 93 SL2 Saturn Slam hard or die when shifted into reverse and also idle high?
I'd have the relay to the lockup torque converter checked. If the relay isn't disengaging, you'd experience the exact problem you're describing.
Where is the data port on the 1999 Saturn?
Just above the left knee of the driver, to the left of the steering column.
How can you tell if your wheel bearings are bad?
Noise is the most telltale sign of bad wheel bearings. Specifically, a rumbling or growling noise while the car is moving, often louder during turns at a low speed, indicates that the bearings need repair or replacement.
