answersLogoWhite

0

🚗

Chevy Trucks and SUVs

Chevrolet is known for its medium-duty commercial trucks and sport utility vehicles (SUV). Some of the current Chevy trucks and SUVs are the Colorado, Silverado, Avalanche, Tahoe, and Suburban.

500 Questions

What is the torque spec Nissan navara con rod and main bearing D22 YD25 engine?

User Avatar

Asked by Wiki User

What is the torque for the big ends for Nissan np300 yd25 2.5 2013

Truck door will not unlock all the way orr open how do i get it to open?

User Avatar

Asked by Wiki User

If your truck door is stuck and will not unlock or open fully, here are some steps you can try to troubleshoot and potentially resolve the issue:

Check the Locking Mechanism: Ensure that the door is not stuck in the locked position. Attempt to unlock the door using the key fob or the key itself, depending on your vehicle. If it's an electronic lock, make sure the battery in the key fob is not dead.

Manually Unlock the Door: If the electronic locking system is not working, try manually unlocking the door with the key. Insert the key into the door lock and turn it in the appropriate direction to unlock it.

Examine the Door Handle: Inspect the door handle to ensure it's not damaged or loose. If it's damaged, it may need to be replaced. If it's loose, tighten any screws or bolts that secure it to the door.

Check for Obstructions: Look for any obstructions that might be preventing the door from opening. This could include debris, ice, or snow that has accumulated around the door frame. Clear any obstructions you find.

Lubricate the Lock and Hinges: Apply a lubricant (such as WD-40) to the door lock and hinges. This can help if the door is sticking due to rust or lack of lubrication.

Try Gentle Force: If the door is only partially open, gently apply some pressure to it while trying to open it. Be careful not to use excessive force, as you don't want to damage the door or its components.

Professional Help: If the door remains stuck, it may be a mechanical or electrical issue within the door itself. In this case, it's best to consult a professional mechanic or a dealership to diagnose and repair the problem.

Emergency Release Cable: Some trucks have an emergency release cable inside the door panel. If the door is completely stuck, you may need to access the cable to release the door. Refer to your vehicle's manual for guidance on locating and using this cable.

Always exercise caution when attempting to fix a stuck truck door, and do not force it open if it feels like it's resisting too much. It's best to seek professional assistance if you're unsure how to proceed or if the problem persists.

How do you install a CD player in a 1989 Chevrolet 1500?

User Avatar

Asked by Wiki User

TO install any stereo/cd player all you need is the correct wiring harness and mounting kit. You can pick them up at your local BEst Buy or another store like it. You will also need to locate the main module for the stereo which is under the dash ( can be view if you remove the cover plate under the steering wheel). Disconnect all connections and use a wiring kit to plug them into. The antenna is also on that module and you wil need an adapter. I just did this to my 89 c1500 and it took a while. And forwarning, it is an old truck and things are fragile so be careful not to break anything.

What is the code po432 on a Chevy Silverado?

User Avatar

Asked by Wiki User

This code is on 2004 Chevrolet silverado po. 432 what does it mean or affects on this truck?

How do you replace starter on 2002 duramax diesel?

User Avatar

Asked by Wiki User

You have to remove the intake manifold, you should be able to get to the nine bolts through the wheel well. Once intake manifold is off, you will see the Starter. Two Connection, one Bolt, and one Nut. Disconnect the Battery first. Very Bad Design, and Strater placement. Good Luck.

How is the radio remove on a 2008 Chevrolet silverado?

User Avatar

Asked by Wiki User

From the Service Manual Vol 5 of 5

1. Remove the Cluster Bezel by applying parking brake, move shift lever (automatic) all the way down, tilt the steering wheel to full down position, Gently pull rearward on the corners of the bezel from the instrument panel assembly, remove bezel

2. Remove 3 screws

3. Pull out slightly to gain access to connectors

4. Disconnect the wire connectors

5. Disconnect coaxial cable from radio (Non-Digital)

6. Remove radio

Install is just opposite from removal

screw tighten to 14 lb in, don't use paint, lube, corrosion inhibitors, locking compound

Make sure all clips are in place on the bezel

How to Replace rear main seal Nissan truck?

User Avatar

Asked by Wiki User

What year? what engine? What transmission?

Need some more info.

Basically though, you need to remove transmission or be able to move it back far enough... remove flywheel from crankshaft end... unbolt and remove rear main seal retainer... replace seal and gasket... reverse procedure.

How do you remove alternator from 2004 Chevy Trailblazer?

User Avatar

Asked by Wiki User

1. Disconnect the negative battery cable.

2. Remove the engine cover.

3. Remove the engine undercover.

4. Remove the alternator drive belt.

5. Remove the alternator mounting bolts.

6. Remove the alternator from the engine.

To install:

1. Install the alternator and torque the upper bolt to 18-23 ft. lbs. (26-31 Nm) and the lower bolt to 33-38 ft. lbs. (44-52 Nm)

2. Install the drive belt. Properly tension the belt.

3. Install the engine undercover.

4. Install the engine cover.

5. Connect the negative battery cable.

Do the connecting rod caps on a Chevy 350 need to be installed in a certain order of direction?

User Avatar

Asked by Wiki User

Yes, the rod caps must be installed on the same rod and in the same orientation.

Diagram for a Chevy 350 install on Chevy love?

User Avatar

Asked by Wiki User

Contact either Chris Alston at Alston Cassis Works, in California, Art Morrison ent., in Washington State, or Hooker Headers. These 3 companies all make kits for this application, which, when done right, looks sweet, by the way. I helped a guy do one once. Well worth the effort....

How do you remove the radio from a 2006 Chevy Equinox?

User Avatar

Asked by Wiki User

You must insert the 5 digit code. If you cannot find the code, then go to the selling dealer. They may have it on file. If not, you will have to remove the radio the get the serial # off the radio chassis. With that serial # the dealer can provide the code. There is no other way.

On a 1996 Chevrolet Pick-up 1500 series how do you replace the ignition switch?

User Avatar

Asked by Wiki User

if tis like a 1995 you need to remove the lower dash panel below the column, the culoumn sleeve that is held on by 2 torx scres from the bottom, then you need a inverted torx sicket to remove to that hold the top sleeve on the column then you can get to the ignition switch

Where is the starter relay for 2002 Chevy Trailblazer?

User Avatar

Asked by Wiki User

If your talking about the engine cooling fan relay and memory serves me right it is located on the radiator support, inside engine compartment, drivers side, down low. It's probably easier to reach from underneath with vehicle lifted.

What Type of battery is needed for a 2005 equinox Chevrolet?

User Avatar

Asked by Wiki User

8The battery is located under the cover immediately behind the Head lamp assembly remove the three screws that secure the cover and push the 4 tabs on the heat sink looking with the cords running from it. (I have no idea what this is does)you can now remove this larger cover to reveal the battery the tighest space I have ever seen in a GM. Mr Freeman - aka naztyfreeman@yahoo.com

How do you replace the ignition switch on a 1985 Chevy truck?

User Avatar

Asked by Wiki User

you pull the steering wheel off and underneath you will see a hole with a pin in it. turn your switch to the run position and push the pin up and it should come out

I have a 83 f-150 and replaced all the keys in it. There is a pin below the ign switch you knock out then pull out the key switch. let me know if it helped!

How do you replace head gasket in 1985 Toyota truck?

User Avatar

Asked by Wiki User

This list is specific to the 1992 Cherokee with the 4.0l I6 engine- hope it helps: loosen and remove the belt(s) Unbolt the exhaust/intake manifolds (there are 13 bolts i think... maybe 15) and discard the gasket- one bolt goes through the power steering mount unbolt the valve cover about 15 bolt unbolt the head (all remaining bolts on the top, and going in sideways from the AC compressor discard head gasket, and clean ALL gasket mating surfaces Put it all back together. MAKE SURE you follow the manual's bolt torquing pattern!!! otherwise you just did a bunch of work for nothing. By removing the head and replacing the gasket.

Where is the location of the electronic spark control module for a 1994 Chevy truck?

User Avatar

Asked by Wiki User

Within the distributor. Many people [including some auto parts stores] often confuse the ECM with the ICM [Ignition Control Module], which *is* located in the distributor. The ECM in this case is usually mounted under the driver's seat.

How do you replace an ignition switch on a 1992 Chevrolet truck?

User Avatar

Asked by Wiki User

It depends on what year. For 72 and earlier (in the dash) follow this. 1. Turn ignition switch to off position and leave the key in the switch. 2. Disconnect the battery. 3. Take a small dia. paper clip and insert it into the small hole in the face of the ignition switch. You will feel a small button that you depress. 4. While depressing the button, turn the key to the accessory position (counter clockwise) and using the key remove the cylinder. 5. You can now remove the bezel by unscrewing it CCW. 6. This will allow you to remove the ignition switch from the dash and disconnect the wire harness plug from the rear of the switch. I hope this helps someone. From an old gear head.

How do you disconnect the horn on a 2003 Chevrolet suburban?

User Avatar

Asked by Wiki User

Find the horn and remove the wire going to the horn/s it should have a connector you can seemly slide off however if it dont you may have to clip the wire and tape the end so it doesn't short if it goes to ground. A horn in many states is required your best cure is to fix the problem and to leave the horn alone. , EzForJesus

Why you connect ammeters in series in network circuits?

User Avatar

Asked by Wiki User

Because ammeters have low resistance. If you connected them in parallel, all the current would flow through the ammeter instead of the circuit you were trying to test, possibly frying the meter but certainly invalidating the measurement.

Why do you connect galvanometer in series?

User Avatar

Asked by Wiki User

You connect a galvanometer in series with the circuit being measured, because the galvanometer is a form of ammeter, although an extremely sensitive one, and ammeters measure the current in a series circuit.

Is a ammeter a resistor?

User Avatar

Asked by Wiki User

Usually, but some voltmeters are limited in the range of resistances they can measure.

Answer

No, voltmeters measure voltage, notresistance.