0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Is there a free engine diagram for Chevrolet express van?
oxygen sensor1 bank 2 on 2005 chevy express 3500 cargo van
Can you adjust torsion bar to lift sagging front of Chevy crew duramax 2006?
Good info about raising front end by adjusting torsion bars.
www.duramaxforum.com/forum/04-5-05-lly-performance-parts-discussion/4491-torsion-bar-adjustment.html
What is the gross vehicle weight of the 2004 Chevrolet Tahoe?
The gross weight of the 2004 Chevrolet Tahoe is 6500 lbs..
What are 1304065903 casting numbers?
If off a transmission, then it is for a Borg Warner Super T-10 transmission with an aluminum case. The gear ratios can be determined by the number of grooves in the input shaft. 2 grooves equals a "close-ratio" design (2.43 first gear) and 3 grooves equals a "wide ratio" design (2.64 first gear). Although it is a Super T-10, the aluminum cases are not as relaible or strong as the nodular iron case.
How do you change a starter in a Chevy Chevette?
First... I'm gonna state the obvious... DISCONNECT THE BATTERY!!!
I would recomend lfiting the entire engine out. That is the easiest way. If you don't have the means to do this, then what you need to do is free the motor mounts so that you can tip the engine to the passenger side. This can be done while the tranny is still attached. BE CAREFULL. The way I did this was to put a hydraulic floor jack under the engine... the front of your oil pan should be able to hold this weight. When you ge tit in position, brace it. You do not want this falling on your hands when you're working. I used the hole on the engine block that is located at the front on the driver's side. I put a srewdriver through it to hold the iron pipe in place I put under it as a verticle brace.
Now you need to remove the breather from the carb. The starter has 2 bolts... the one on the bottom can be accessed easily enough while under the car. The one on the top is the cussing fit. You're gonna have to squeaze your hand between the firewall and the intake manifold. Your only going to be able to turn this one a quarter turn at a time. Have fun. After you have it out a little and the starter starts to drop, you might be able to snake an 18inch extension with a socket on it into the hole.
Once its off, make sure to keep track of the wires on the solenoid. Don't let one of them get lost. This is the part that there is no easy way around. You're gonna have to disconnect just about every wire and hose on that side of the engine in order to twist and pull that starter out. Its slightly easier to slide the next one in. Then everything just goes in reverse. Make sure you reattache the wires on the solenoid before bolting it up. Put the top bolt in first. It'll make your life a WHOLE lot easier. Now have fun reattaching all of the vacuum lines, fuel line, and wires. Double, even triple check everything and make sure its all plugged up right. Now cross your fingers and hope you hear the beautiful sound of it cranking.
another suggestion
you do not need to pull the engine out of the chevette all you have to do to replace the starter is as follows i have done this many times
this is the easiest way i found
Step 1 unscrew and remove plastic panel below steering wheel
2. pull back carpet enough to remove 3 bolts from the steering column on the floor
3. remove 2 bolts from metal bracket holding steering column to dashboard let steering wheel rest on drivers seat
4. jack up car (remember to chock back wheels!!! bricks large rocks firewood just do it) then unbolt rag joint on steering Assembly ( follow steering shaft down to small circular thing with 2 bolts) unbolt this
5.fold drivers seat down and pull steering wheel and column to back seat or until it stops you may have to disconnect the wiring going to steering wheel
6. remove wires from starter
7. get some extensions for ratchet reach in and unbolt old starter it will be very tight but is much better then removing engine you will have some trouble with the bolt on the side by the engine you will not have much room to move ratchet but it will work.
8. to put it all back together just reverse directions
Have worked on chevettes for over ten years now this is the easiest way i have found
keep driving your vette i still drive my 78 everywhere
Myk
1/7/2009
What does a diagnostic code 128 mean on a Chevrolet blazer mean?
well in order for anyone to answer that you need to specify what is the make,model,year,and engine type because the program most mechanics use need all that information
What kind of fuel does the 2010 Chevrolet Suburban use?
The 2010 Chevrolet Suburban runs on flex-fuel (FFV).
Why does the torque converter chatter when you drive?
It can be the lock up on the torque converter not functioning properly. It can also be low of fluid. Check the transmission fluid level. If the fluid level is good, you need to seek professional help.
What is the combustion chamber size of heads with casting number 354434?
The chambers are 60cc. The heads are from 77-78 307 engine.
Whats the computer on a 1988 Chevy 4-cylinder 2.5 engiene 5 spd?
The computer basically controls all functions of the vehicle. If you are having problems cutting out missing shutting down for know apperant reason then the possibilty of the computer going bad may be the problem. The computer is located under the glovebox and the bracket is normally held in with one screw into the bottom of the dash
How much fuel can a corvair 1965 hold?
A 1965 Chevrolet Corvair fuel tank holds 14 gallons of gasoline.
What did they call the car that Chevy Chase drove in the movie Vacation?
The "Wagon Queen Family Truckster", which was a heavily modified Ford LTD Country Squire II.
What did the Chevrolet heads with the dual pyramid stamp on the side come from?
The 327 Chevy used those heads. Also for a detailed list of original applications take the numbers off from the heads and check them in "CHEVROLET BY THE NUMBERS" manual written by Alan L. Colvin. This will tell you exactly the year , model, dates when those heads were used.
What type of engine is in a 1987 Chevrolet Silverado?
You had the option of..
- 4.3 Litre (262 CUID) V6
- 4.8 litre (292 CUID) Inline-6
- 5 litre (305 CUID) V8
- 5.7 litre (350 CUID) V8
- 7.4 litre (454 CUID) V8
- 6.2 litre (379 CUID) V8 diesel
What is the biggest four cylinder motor made by Chevrolet?
The 2.8 Liter found in the current Chevrolet Colorado, & GMC Canyon pickups is the largest Chevy 4 cylinder they make.
Where is the number 2 and number 7 cylinder on a 2001 Chevy 5.3L Vortec?
#7 is the very back spark plug in the drivers side head. AND from front to rear will be cylinders 1-3-5-7
#2 is the very front plug in the passenger side head. AND front to rear is 2-4-6-8 cylinders. The firing order is 1-8-7-2-6-5-4-3
How many quarts of oil in a 1968 Chevy motor?
Most all V8 & inline 6 cylinder engines required 5 quarts with filter change. Just park the car on a level surface, drain the oil and replace the filter. Add 4.5 quarts and start the engine and let run for 60 seconds. Shut off and wait 1 hour. Check the level and add as necessary. You now know the capacity.
How do you change an ignition switch on a 1982 Chevy pick up?
The switch is located on the left side of the steering column, underneath the dash. You will have to remove the lower dash panel and some of the ductwork to gain access to it. You will need either a 5/16" or 8MM driver to remove the two screws that hold it to the column.
How do you change the front rotors on a 1996 GM Chevy Sierra?
What is the difference between a c10 and a k10?
The C designates 2 wheel drive the K designates 4 wheel drive.
What kind of fuel does the 2011 Chevrolet Suburban use?
The 2011 Chevrolet Suburban runs on flex-fuel (unleaded/E85).
