0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Will a 271 Detroit Diesel fit a 1960's Chevrolet bell housing?
No.The engine has a number "2" or "3" SAE flywheel housing that has a 360 deg. bolt circle."2" has a 18-3/8in. bolt circle."3" has a16-7/8in. bolt circle.I have a aluminum "3" housing that has the proper transmission holes to mount a chev. 4-speed-3-speed std.937-879-3532.
How do you change the cabin air filter on a 2009 Chevy hhr?
Purchase a purolator cabin filter. It comes with complete instructions.
Where is a 02 sensor located on a silverado Chevy year 2000?
There are several O2 sensors on that vehicle and they are all threaded into the exhaust system at various points.
What is the 1984 timing advancement for a chevette?
On 84 factory base timing is 8 degrees b4 top dead center and should have no more than 32degrees spark advance total by 3500rpm. You can play around with base timing. If you have a manual trans you can put your base timing around 8-12 degrees and 8-18 drees automatic trans. Each dree you advance the base timing you will have to decrease centrifugal advance as well to keep engine from pinging from detonation. Carb tuning is also a must when timing is changed. Ive personally seen gains of 10 hp at the wheels and up to 15ftlbs of torque with proper timing and fuel curves. Hope this helps. Happy Tuning!
How do you change the ECM in your 1993 Chevy 1500 pickup?
Pull your glove box. Located on right. Disconnect 2 wiring harness's then unit will slide out with a little "wiggling". New ecm will need you to pull the prim , rubber stops and clips from your old ecm and replace on new ecm. Most parts stores will let you use tools at the counter to replace right there.
The way you explain it it sounds like your engine has hydrolic lifters. With these I have always tightened the rockers until the pushrod gets hard to spin and wont move up or down and then ONE HALF TURN not a full turn. The valves might open but within a minute or so should close. This is cause by the lifter bleeding off leftover oil in it. Hope this helps.
How do you change a body on a 85 Chevy half ton pickup truck 4x4?
what is the body being changed too?
What size tires fit 1984 Chevy?
WE need to know what size wheels you have on it, Like 15" 16" and so on. Also need to know how wide the wheels are too.
Can you show Blue Prints For A 1995 Chevy 5 Speed Manual Transmission?
GM manufactured several models of manual transmissions - they weren't all the same - and there'll be quite a substantial difference between a manual which was used in a Silverado and one which was used in a Cavalier. Try again with the transmission model.
How do you prime the fuel system?
All you need to do is cycle the ingnetion key on wait 3 seconds then repeat 3 or 4 times. but there is no reason to prime fuel system on fuel injection. All you need to do is cycle the ingnetion key on wait 3 seconds then repeat 3 or 4 times. but there is no reason to prime fuel system on fuel injection. All you need to do is cycle the ingnetion key on wait 3 seconds then repeat 3 or 4 times. but there is no reason to prime fuel system on fuel injection.
What is causing the check engine light to stay on the egr valve is clean and carbon free?
If you just cleaned the EGR and replaced it, you can turn off the Check Engine Light (CEL) by disconnecting the negative battery cable for a couple of minutes. The engine may run rough for a few miles until it "re-learns". If the CEL comes back on, take the vehicle to AutoZone for a free scan. If the code still indicates a faulty EGR, it may have to be replaced.
When and how did the Chevy bowtie originate?
It was 1913 when it was originated. The owner of Chevy was in a hotel room in parris and the wall paper had nothing but the Chevy bow-tie you see today. He cut one off the wall and walked out to his Chevy He put it up to the Chevy and notice it looked perfect for all his vehicles.
How do you change cabin air filter on 2007 Chevy Equinox?
Purchase a Purolator Cabin Filter. It comes with detailed instructions.
Why would a 2000 Saturn SL-2 with a new thermostat still overheat?
check to see if your cooling fan is working if so look at your radiator cap and make sure the cap gasket is not broken.
AnswerThe easiest way to see if your fan motor it still working is to run the A/C in the car, this triggers the relay for the fan. If the fan works and the car still overheats you will most likely new a new Coolant Temperature Sensor. There are two of these sensors. One controls the temperature gauge on the dashboard. The other takes a direct temp. reading of coolant. It is in the front right side of your engine just below the valve cover, you will see two small wires leading to it underneath the air filter. Answersometimes when you loose some coolent like when you changed the thermostat you get an air pocket trapped inside the engine witch will cause the engine to overheat.you have to bleed the air out. AnswerThe most likely cause is the coolant sensor located in the cyl haed on the back of the engine It has a small 2 wire connector attached to it. Unplug the connector and see if there is any corrosion on it If there is you will need a ssensor and harness. If not change the sensor It's only 18$ Canadian from Saturn Stay away from aftermarket on this as they never work properlyHow do you replace a ring and pinion gear in a 1994 Z71 Chevy pickup?
it's best to get a shop to do it....unless you have all the specialty tools to do the job...if it isn't set up right....it'll be torn up in 6 months or less
What is the problem if check engine light comes on Chevy Tahoe 1999?
That means that the computer system has recognised a problem with the emissions system on the engine or transmission.
The FIRST thing you need to do is to have the computer system scanned with an engine scanner to find the area the problem may be in. Some parts stores will do this for FREE. Don't start replaceing parts. Have it scanned FIRST.
How hard would it be to drop a 454 chevy big block be in a 1988 Nissan z31?
Pretty hard...the biggest possible stock engines in these cars are the 3.0L V6 and even with that the engine bay space is pretty limited. In contrast, a 454 is a V8 (so one cylinder pair longer) and in liters it's equivilant to around 7.4. That means that you're not only adding 2 more cylinders but also making all 8 over twice as big! All in all, you would have to knock out the firewall, take out the center console, and basically use the transmission as an arm rest in order to make it work.
How do you remove the tail light lens covers of a 1990 GMC truck?
The screws are either gonna be Phillips or torques head, so act accordingly. there should be to on the outside corner, and if you open the tailgate there should be two more in there. after removing all four the assembly will hinge open almost like a door.
There are 2 tab locks, 1 at the top and bottom of the assembly. On the bottom is a small hole for prying it open. GENTLY hold the tab back while prying the assembly open.
Scrape the sealant goop out of the grooves and fill the grooves with black or clear silicone. Position the back up light reflector and the foam gasket.
After that it snaps back together easy as pie.
