0
Buick LeSabre
This category covers questions about the Buick LeSabre, a full-sized entry-level luxury sedan manufactured by the Buick division of General Motors. The LeSabre replaced the Buick Special and was in production from 1959-2005. It was later succeeded by the Buick Lucerne.
2,607 Questions
What could cause a 1994 Buick Lesabre not firing?
have u checked spark plug wires, ignition coils, timing,spark plugs or had it hooked to a reader?
The code P0452 on a Buick LeSabre is a fuel tank pressure sensor circuit low voltage warning. This sensor is on the top of the fuel tank.
Where is the air bag sensor located in a 2005 lesabre buick?
air bag sensor located between the lower radiator support and front bumper.
Where is the thermostat on a 91 Buick LeSabre Custom 3.8L?
This guy is mostly right, but these cars only have one (1) bolt holding the thermostat housing on, you have to take the piece of plastic trim off the intake that has "Fuel Injection 3800" embossed in it to get to the thermostat. As you're putting the thermostat housing back on wiggle it a little as you're tightening the bolt to mske sure it goes in all the way.
How do you check service engine soon codes on a 1995 Chevy Blazer 4.3L V6 4x4 2-dr?
Some Auto Parts store now have the tools to read codes
How do you take off a windshield wiper on a Buick LeSabre?
The Buick LeSabre has the most common hook-end wiper arms. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
How do you reset the low tire pressure indicator on a 2004 Buick Le Sabre?
I don't think any sensor directly measures the pressure. I believe the wheel rotation sensors compare the rotation of all four wheels for a certain period of time and if one is consistently turning faster than the other 3, it indicates a low pressure. With low pressure in the tire, the diameter is effectively reduced making the tire turn faster. You may have a bad rotation sensor on one wheel.
Are there conditions that cause a false po442 in a Buick's diagnostic test codes?
PO442 is a Service Engine Error code can be caused by one of the following:
1. Defective or loose fuel cap
2. EVAP canister or hose cracked- not connected
3. Purge or vent solenoid defective
4. Vaccum leak at engine
check the bulbs?
What does error code 13 mean on a 1998 buick lesabre mean?
the 2 digit code 13 means- problem with oxygen sensor or circuit
Does a 1995 buick lesabre have a camshaft positioning sensor?
I would think that any car without a distributor would have a cam sensor and a crank sensor. For the computer to send the fire signal to the correct spark plug it needs to know the position of both shafts. The failure of either of these will cause the engine to die. Older cars used the distributor to do this mechanically.
Can you put a belt on your 1997 Buick leSabre without going on the AC Compressor?
You have to go on the compressor! My husband has a 95 and the auto parts manager told him you have to.
How do you preset radio stations on a 1988 buick lesabre?
If I remember correctly, those models may be old-style 'push-button' type radios? If so, do the following:
1) Select the 'station' or frequency you want to store as a pre-set by turning the right (tuning) knob.
- In older models, FM or AM doesn't matter, as the button is only "remembering" a position on the dial.
- In newer (but still push-button or 'old-style') models, the button will also switch between FM and AM, but each button remembers BOTH the band AND the frequency, but will not remember more than one station (I.e. The button wouldn't remember one station for FM and a different one for AM) on the same button -- except of course, if those two stations happened to be exactly the same linear position on the dial.
2) Pull the 'push-button' mechanism out towards you all the way (one click, usually) -- it may take a little more effort than you think or you way need to lift up slightly on the push-button to get it to move, especially if it's been a couple of decades.
3) Push the 'push-button' back in all the way -- the linear mechanism on the dial should not move at this point.
4) Test your new pre-set by moving the dial to the left or right using the right-hand (tuning) knob then pushing the same 'push-button' in. The linear mechanism -- if working properly -- should now move the dial to your new location and change the frequency to your chosen 'station'.
On new (digital) radios in cars & trucks, of course,with the radio on you tune in the band and frequency (and in some cases a 'bank' of presets [such as 'FM1', 'FM2', 'XM1' / 'SAT1', or 'AM1']) that you want to store then push 'set' then push the preset number you've chosen OR push-and-hold the chosen pre-set button (generally the radio will beep and / or flash the display and / or audibly re-tune the station once the setting has been stored) with the 'push-and-hold' method it may take up to three seconds in some cases for the setting to 'take'.
If you're having issues, hold the button in a bit longer until you get some sort of reaction from your radio and / or watch the radio's display to see if there is a message or prompt, as in many cases the radio may ask you if you REALLY want to change an existing preset, or the radio may need more information such as the 'bank' [again, meaning something like 'FM1', 'FM2', 'XM1' / 'SAT1', or 'AM1']in which you want to store the preset. Hope that helps!
AnswerShould just be able to select desired station and hold button for 3-5 seconds until blinks AnswerShould just be able to select desired station and hold button for 3-5 seconds until blinksHow do you check the fuel pump of a 2000 Buick Le Sabre?
you will need a fuel pressure and flow gauge and then check actual meaured to specs.
How do you check transmission fluid in 1994 buick lesabre?
After you have driven the car and the transmission is hot, pull the dipstick out that says "Trans Fluid". It will be longer than the dipstick for the engine oil. You read it the same way as the oil dipstick using the holes at the bottom as level indicators.
How do you extract codes from 1994 buick lasbre?
You have to buy a decoder that you plug into your car:)
How difficult is it to replace the blend door actuator on a 2007 Chevy Impala?
Pretty difficult unless you have small hands. Under glove box is very tight. Only a couple screws but hard to remove and bolt back in. Would be simple if you could get to screws. I am trying to get mine out now. Anyone have any tips?
How do you replace or repair sunroof drain tubes on 89 Accord Drivers side?
stick some thin wire down the holes
In an 89 Subaru gl 2wd what is the Allen key for in a pouch under back seat?
INOPERATIVE AUTOMATIC SHOULDER BELT, BASICALLY THIS WRENCH IS TO ADJUST THE AUTOMATIC SHOULDER BELT WHEN IT IS CAUSING PROBLEMS LIKE THE WARNING LIGHT DOES NOT GO OFF,THE SETTING FOR THIS WRENCH IS LOCATED BEHIND THE DRIVERS SEAT OR PASSANGERS SEAT TOWARDS THE SUPPORT ARM AT THE BOTTOM, THE SETTING BOLT IS COVERED BY A PLASTIC CAP YOU HAVE TO REMOVE THE CAP AND USE THE ALLEN WRENCH THERE IS A ILLUSTRATION IN THE OWNERS MANUAL ON HOW TO USE THE WRENCH, I HAVE A 1989 OR 90 SUBARU LEAGACY WANGON "L" SERIES AND IT HAS THIS WRENCH ALSO, HOPE THIS HELPS YOU IN ANY WAY.
What does a problem code 41 on your 1989 buick mean?
41 = faulty ignition module cam sensor (3.8L) look at all codes at this site: http://www.troublecodes.net/GM/ no comment nothing further
How do you bypass the security ignition key if you don't have the ignition key with the chip?
The cost of doing this would be more time consuming and more expensive than going to a locksmith or a dealer and getting a key with a chip.
