Bumpers

yeah i got a $116 ticket for not having a rear bumper on my car

There are mounting screws located on both sides of the rear wheel arch, loosen then and the bumper will come right off.

Spray some PB Blaster on the rusted bolts. Remove bolts and take bumper off. Install new bumper and new bolts. Used anti-seize on the bolts.

The rear fog lights are accessable from under the car. You have to reach up and under the rear bumper.

On a Series 1 Discovery just UNBOLT the CENTER section of the bumper fascia. (the plastic part) Then, using a dremel or similar rotary tool, cut the ends @ the angle line to match.

It should, but the upper bumper pad on the 2500 may be thicker, they both bolt on the same way though, measure the height.

NO, not even close.

Get some drunk dick without insurance to turn a corner too wide and smash your front end, then drive off. It worked for me!

Yes, it is possible to do so. If the cars Body type/style are the same and if the model are the same you can interchange parts.

Can_you_drive_a_pick_up_truck_without_a_front_bumper

Looking at the bumper, you will see raised, chrome, dome shaped, bumps. These are actually bolts, with a nut on the back sides. Then, it will just lift off.

Patriot Depot, Stamp and Shout, and Cafe Press are online stores that carry Coexist stickers. Northern Sun is a retailer that carries these stickers in their store as well. Some major retailers such as Target and Wal-Mart usually carry them too.

Yes.

To remove front grill on a 1999 seat Ibiza, remove the 6 tabs on the hood. Then unscrew the front grill and release the 4 clips that hold the grill in place.Ê

yes it should.

With tools.

in washington state A motor vehicle must be equipped with a bumper on both the front and rear of the vehicle with the exception of motor vehicles where the original or predominant body configuration, provided by a recognized manufacturer, did not include such bumper or bumpers in the design of the vehicle. For the relevant model year, bumpers must accommodate recognized manufacturer impact absorption systems pursuant to applicable SAE Bumper Standards or equivalent standards.

NO

Super glue

Hello,

Do you want to replace entire rear bumper or bumper cover? Are you doing it yourself or having shop do it? You can buy a new bumper cover (primed, so you'd have it painted too) for about $200. You can surely pick one up by hunting junkyards or sites like upullourparts.com

Mike

if you look around the headlight, there are silver clips that hold the clear cover of the headlight piece, i think there are two on the top and two underneath between the bottom of the headlight and the front bumper. release the clips and the lens comes off, then giving you access to the screws holding up the bumper to get it off. it's easier to use needle nose pliers or something to grip the clips while unscrewing the screws holding up the bumper sides to both front fenders located at the top corners of the bumper on either side in the wheel well. As for the entire headlight assembly, there are screws from the back and outer sides of thepieces to unscrew. Don't forget to unscrew the bulb from the back of the headlights and remove the corner lamps(one screw on each side visible from overhead)by sliding them forward. Previous answer is wrong. The headlights on 1994-1997 Accords are sealed units, and do NOT come apart. To remove the front bumper and headlights: Use Phillips screwdriver to remove five screws from the grille, four on top, and one is hidden down lower, near the hood latch. Remove one screw each from the corner lights as described above. Gently pry them forward to unfasten the pegs from their holes in the fenders. Twist to unscrew the bulb sockets. Unfasten the black plastic rivets that attach the bumper cover to the rubber wheelhouses underneath, on both sides. At the upper rear corners of the bumper cover, remove one screw from each side that attaches the bumper cover to each fender. Using a Phillips screwdriver, reach in through the air intake grille in the bumper, at an angle, and remove one screw per side that holds in the turn signal lens and housings. Remove and unplug these. Using a long extension and a 12 MM socket, reach through the openings where the turn signals were, and loosen the bolts that hold the bumper structure to the radiator support frame. The bumper is slotted, gently lift it off of the top two bolts. The headlights are now removeable with a 10 MM socket, bolted through the top, each side, and lower front corner toward the center of the vehicle (not from the back as incorrectly stated above). The lower headlight bolts are NOT accessible with the bumper and cover still installed on the car. The plastic rivets that attach the cover to the bumper structure can now be easily accessed without ruining the headlights.

yes it will fit ther is no diff. in the cars ex. that the si has a sun roof and a diff motor but the bodys are the same\.

If it is old chrome that is rust corroded, I would use NAVAL JELLY a couple times over then follow that up with turtle wax brand chrome polish with rust remover applied with a brillo pad. Keep going over and repeating and you will get it cleaned up. Once done, dry it and apply WD40 to the chrome ;this seals the pores in the open metal to keep it looking as good as possible.

Bumper mounted park lamps

No