0
Chevy Blazer
The Chevy Blazer may refer to any of the sport utility vehicles manufactured by the Detroit-based automaker General Motors Company. Some of the popular Blazer models produced by the company are the TrailBlazer, the S-10 Blazer and the K5 Blazer.
5,824 Questions
Why does my 2003 Honda crv remote fob no longer opens or locks driver side door?
If it's only the driver side door, it's most likely a wiring connection within the door. If NONE of the doors are opening with your fob, you'll just have to change the button battery inside of the fob.
How much oil does a 2000 Chevy blazer take?
depends of size of engine. 6 cyl about 5 quarts with filter changed
Should there be power in both wires that go to the fuel pump on 91 s10 blazer?
No. Only one wire should have power, the other is the ground.Type your answer here...
What type of coolant should you use in a 2001 Chevrolet S10 pick-up 4.3L v6?
The manufacture recommends Dex-Cool.
How do you remove the oil pan on a Acura TL 1998?
remove the differential. it has 5 17 mm nuts around the diff. then
Where is fuel pressure sensor located on 01 blazer?
there is none.
there is a pressure regulator however.
and there is a tank sensor sometimes that measures pressure in the tank. but not on all vehicles.
Why won't your Chevy blazer 350 v-8 start without starting fluid?
1995 blazer350 v-8 wont start unless i use starting fluid,once on it idles high
How do swap 4l80e into a 1988 k5 blazer 4x4?
You can't. The 4L80E is an electronic computer controlled transmission. The 88 blazer computer will no shift the transmission are even begin to work.
How do you unlock the anti theft system that has been activated on a 1992 Nissan Maxima?
YOU NEED TO CALL NISSAN GIVE THE LAST 8 DIGITS OF YOUR VIN#.THEY CAN CUT YOU A NEW SECURITY KEY...THAT KEY IS THE SECRET..........BUDDY MACK..
How do you replace the heater core in a 1996 Chevrolet Blazer?
Ok you have to remove your all the parts of your dash. When this step is done, you gonna see a plastic black box, remove this one (3 Screws). Under this one you can see your heater core.
When this step is properly do, open your hood. Look on your firewall (Up Passenger Side) and remove all bolts, remove the 2 heater hoses. Remove your heatercore and replace it, Redo all of this step inverse for reinstallation! Good luck!
(Sorry my english, im not the best in this language!)
But before you replace it...
If you think it may only be clogged, turn heater controls to full open/hot. Then turn off engine. Disconnect heater hoses under the hood. Connect a short hose to the "input port" to carry dirty water away from your engine. Connect another hose to the "output port." Shoot water from a hose-end sprayer into the "output" to backflush the core. My heater in 98 Blazer had quit heating. I just had to wash the crud out it it worked fine afterward. (it was going to be a BIG job to take off enough dash parts to get to the core to deal with it)
Is there a manual release for the tailgate on a Chevrolet Blazer?
I just went thru this on a 2002 s-blazer. Thier is a access hole behind the carpet on the rear inner gate panel. If you peel the center top of the carpet down you will see a small punch out behind the carpet. The punch out is about 3/8 of a inch high and about a inch long. If you punch this out you will see a gold colored lever insid the access hole, you can stick a screwdriver in their and slide it toward the passsenger side of the vehicle, this should release the gate glass. Good luck,Techboy23
How do you remove the driver side door panel on a 1997 Chevy Blazer?
grab the front of your power window switches and lift up is should be easy then there is two 7mm bolts under your handle to close the door and Philips screw behind lever to open door pull the bottom of the door first the top is on a lip by the window
What is the best way to repair the holes in the door that the window regulator rivets go through?
I'm guessing you mean how to install a new regulator? Nuts and bolts with either lockwashers or stopnuts are fine, it does not need to be rivited. Put the bolt in from the regulator side. If the holes are torn out, you could weld washers over the holes if welding is availible. If not using a fender washer to cover the hole and tightening the bolts very hard should work.
Where can i find the low pressure port on the compressor on a 2003 Ford ZX2?
If you don't know how to logically find this, i don't think you should be messing about with air con. You can injur yourself and cause damage to the system by messing. Why not take the car along to a professional? Thay can recharge your system with the correct amount (and type) and change the oil and/or filter drier which may need to be done if your system is very low. I assume you are looking for the LP port totop up. If your system is very low you will need more than just putting in some more refrigerant. You will need to check for moisture and leaks. If you have moisture in the system it will cause damage to the compressor if not removed. If you don't find out where you have lost gas from and fix it, you will be in the same situation again as it leaks out again.
Why would the heater blow warmhot air while driving but cold air when sitting still?
Possibly defective thermostat. It sounds like it is opening up a bit with increased pressure caused by higher engine revs - when idling, the pressure decreases and the thermostat valve closes. Just a thought, anyway.
Yes. Go to San Francisco -- they're called "cable cars." Next, if you can state your question clearly, what is it you're trying to do? Put a piece of wire in a car? Get cable internet in your car? (The word cable means 'wire' so if you want 'cable in the car' it will work fine unless you move the car.) If you want to get internet access in your car (while it's moving) you should consider the commercially available solution -- get internet access on your cellphone -- many modern handsets can connect to your laptop and supply internet access via the cellphone system.
Any other solution will just waste your time. If you stop the car, you might get (steal, borrow, use -- choose your favorite verb) wi-fi 802.11x internet signal from some stranger's wireless router, but as soon as you move, you'll lose their signal -- they only go about 100 feet. You could sit in the parking lot of a sandwich/coffee shop or a truckstop and get free wi-fi access to the internet, too. Check jiwire.com for a list, or do a search for 'free hotspot'
1998 Chevy blazer roaring noise quits when you slightly turn steering wheel to right?
Worn right front wheel bearing.
Who makes car batteries for walmart?
Johnson Controls as of 2010. Prior to that they were made by Exide.
Will the turn signals work without the hazards flasher in on a 1997 Chevy S-10?
Yes, they are 2 separate systems with separate flashers.
What is a P0186 error code on a 2000 Chevy blazer?
Trouble code P0186 means: Fuel Temperature Sensor B Circuit Range/Performance
Hey Becky==There probably is part of the linkage that has come loose. GoodluckJoe
answerThis problem applies to 95-98 Blazers as well as the GMC and OLDSMOBILE versions. On the newer blazers they have a secret hole in the back of the tailgate where you can insert a rod to release it.The key to the solution is to get the window to unlatch first do that you can open the tailgate and then perform the repair inside the tailgate. This was not easy. I got very frustrated even after reading some of the other "answer" suggestions like the Allen key method. To unlatch the window you will have to climb inside behind the tailgate facing out. You need to make a tool using a bent piece of heavy wire 12" long (like a coat hanger - but preferably stiffer). Bend a 90 degree hook in the end about 1-1/4" long. Make another bend about 6" away from the first bend to make a "J" shape.
Hold the tool parallel to the glass and slide down - hook first - into the center of the plastic hump concealing the latch mechanism. Rotate the tool so that the hook faces the front of the vehicle (the 1-1/4" section should be horizontal at this point). Line the tool up about 1/2" to the passenger side of the hump's centerline. Push the whole tool straight down with about 2 pounds of pressure. This pushes on the release and the window will pop. After you get the window to pop you will see how the latch is made and it will seem easy. I made a drawing I can fax to those who need it. Fax your request to 718-857-8499 and I will fax back the sketch. In the future I will get drawing scanned, I will post a link.
After you get the tailgate down,You will need to remove the back interior panel of the tailgate, this has 3 screws, 1 in the top middle and 1 on each side, after they are out it is just held in by clips so remove slowly. With this removed you should be able to look through little access panels to see if something has come apart, some of the assemble you can reattach from this point for harder to reach areas you will need to remove the steel panel. This is easy it just has a lot of screws and a couple of clips you need to unclip. Just remember what screws and clips you unhooked so assemble will be easy as well.
How do you pull out the dash in a 1988 Camaro and install a heater core?
If you get a haynes manual it shows you how to take out the dash. but mostly the only other thing besides the dash is the steering colum, I don't remember if you have to take the gage cluster out but it's not hard just get a manual it will tell you how.
