How do you remove the door panel to get to the door handle on a 1998 Mitsubishi Eclipse?
I have a 99 eclipse and I just took off the interior door panel to gain access to the exterior door handle. Anyway, after you remove the two screws holding the panel on,(the one under the handle you pull to open the door and the one down in the handle to pull the door shut) note to get to the second screw you must remove the little square plastic piece with a screw driver. Next you have to take off the black plastic piece that is around the door handle and lock. To do this you need to pry it up in the front with a screwdriver or something and push forward from the back of the piece. There isn't much holding it in place, just two little lips of plastic. after that there should only be what I think they call pop rivets holding it in place,just work your way around the paneling with a flat head screwdriver or a putty nife and jently pry it loose. I don't think there were any other screws to take out.
Where is the temperature sending unit on the 2001 Impala with the 3800 V6?
had a problem with my 2001 impala 3.8. dealer said it temperature sending unit, then water pump neither fixed the problem. finally replaced the thermaostat and that worked. don't know if that is your problem but may be something to think about.
Why would your 2002 impala low oil level light come on when the dip stick shows full?
The oil light is not a light that tells you the oil level is low. It tells you that the oil pressure is low. Either the oil pressure sending unit is bad or you possibly do have low oil pressure. If you do indeed have low oil pressure then the oil pump my be bad or one other possibility is a defective oil filter. Replace the filter with the proper AC/Delco filter and see if the condition still exists. If so then have the oil pressure checked to see if you have good pressure. If you have good pressure then replace the oil pressure sending unit. Do not drive the car until you get the condition repaired.
Although the oil pressure light doesn't indicate oil level, GM vehicles do have an oil level sensor located in the oil pan that will indicate if the oil level is low. It is common for this sensor to fail causing the LOW OIL LEVEL indicator light to go on. This light is yellow indicating service is needed, however the OIL PRESSURE light is red and this would indicate an EMERGENCY, seek immediate service before the oil pressure fails completely causing engine failure.
Where is the power steering pump reservoir on a 2003 impala?
Way down behind the engine on the passenger side for the 3800. Not sure if the same on the 3.4 You can see it but need skinny hands to pull the cap/dipstick. I made a small funnel with a foot or so of small hose on it to top it up. You kind of have to fill it blind and keep checking with the cap/dipstick. Do not overfill. Will usually whine if low.
TT
Where is the transmission refill for the Chevy Impala 2001?
way down inside the rear of the engine compartment, by the firewall. Left of center in the vehicle. You will need a funnel and tube to put in fluid. There's a picture in your manual, if you still have.
How do i turn off my low tire pressure light on a 2002 Oldsmobile alero?
its in the owners manual. push the red button in the fuse box
What causes rear end drift on light snow and slush?
Loss of traction caused by an inexperienced driver going too fast or not knowing how to drive in snow. SLOW DOWN!
How will you know if you have a blown head gasket?
Loss of coolant with no apparent leak, engine overheating, oil level overfull, white smoke from the exhaust especially at start-up that smells sweet, a white/grey foamy substance on the underside of the oil fill cap, air bubbles escaping from the radiator with cap off engine running, & possible engine miss.
What does it mean when the car cuts out and wont start back up while driving in a 2009 Chevy impala?
Gotta ask if there is fuel in the tank. Sometimes the fuel gauges give inaccurate readings.. Could also be a clogged fuel filter, bad fuel pump, engine timing, spark gap.
Where is PVC valve located on 2003 Chevrolet Impala LS 3.8?
where is the PVC valve on chevelet impala 2003
What oil filter does a 2000 impala take?
3.4 & 3.8 engine
Fram Extra Guard PH3387A
AC Delco PF47,
Purolator Classic L10111
What is the front head room in the 2003 Chevrolet Impala?
The 2003 Chevrolet Impala has 39.2 in. of front head room.
What is the drivetrain warranty on the 2014 Chevrolet Impala?
The drivetrain warranty of the 2014 Chevrolet Impala is 5 yr./ 100000 mi..
How many gallons does the gas tank in the 2013 Chevrolet Impala hold?
The gas tank on the 2013 Chevrolet Impala holds 17 gal..
What is the drivetrain warranty on the 2009 Chevrolet Impala?
The drivetrain warranty of the 2009 Chevrolet Impala is 5 yr./ 100000 mi..
How do you remove or lower the back headrest on a 2011 Chevy Impala?
Hello. I have a 2011 Chevy Impala and the backseat middle headrest prevents good visibility and, thus, is a driving safety concern. Do you have any suggestions? Thank you!
Hal
Will a 96 impala ss rear end fit a 1983 caprice classic?
Since they're basically the same platform, it should fit without much problem.
What is the biggest engine you can put in a 2010 Impala?
If you really love motors like me, you could try to take a 383 Stroker (not 383 Chrysler, which is way better anyways) and cram it into the impala. You will need to make modifications though and maybe even change the transmission.
Where can one find a 1967 Impala in the Syracuse NY area?
There are lots of automobiles available in the Syracuse area. However finding a specific Year, Make, and Model may prove to be difficult. There are many magazines, books and websites available to find the exact vehicle desired. Some of them include; Autotrader, Cars, Craigslist, eBay and Kelly Blue Book.
What is the proper order to bleed the brakes on a 2005 Chevrolet Impala?
In almost all cases you go to the farthest cylinder first. That would be right rear, left rear,right front and last the left front. Just a tip to prevent any problems with the master cyclinder.The person that pumps the brake should place their left foot on the floorboard underneath the brake pedal. They should pump the pedal and hold it. The person doing the bleeding should lightly crack the bleeder and let the fluid come out slowly, while watching for air. When No more air comes out then close the bleeder. The one pumping should NOT let the pedal go to the floor as it should rest on their left foot. Proceed till all air is bleed. This same procedure work for hydraulic clutches as well.