Chevy Impala

Speed sensor in the wheel hub could be bad

brake fluid may be low

master cylinder may have a leak

brake booster cable may be loose.

or its time to change the brakes

The 2006 Honda Accord is a better gas saver than the 2006 Chevy Impala.

to adjust idle on 2000 impala....Locate the accelerator cable on the throttle body.Have someone push down on the accelerator pedel while you observe the throtle body cable movements.You will notice a stop screw on the throtle body butterfly where it comes to rest against the throtle body.Turn the screw clockwise for more rpm, turn the screw counter clockwise for less rpm. I am not sure if any of the air filter componets need to be removed or not... Should't have to do this.Observe...you can do it...

There is a couple of nuts on the clutch rod and they jam or tighten against each other.Loosen the jam nut back off about 6 turns and then backoff (shorten) the other so that the travel of the rod is less. when you slightly depress the clutch you want 1 inch of play before you feel any resistance. when you have the 1 inch then tighten the 2 nuts against each other.

its a censor that's gone bad in your car take to a mechanic and have them run a diagnostic then you will know which sensor or call your local Chevy dealer

Left Side of the engine: in the sensor case attached to the vacuum hoses

5 by 115

Same place the dipstick is. Use a long skinny funnel.

First you have to remove the fender brace completely so you have room to remove the battery. Then remove the negative cable FIRST it is the black one, and it should take a small end wrench to do so. Make certain the wrench you are using is short enough to NOT be able to reach across to the positive cable. Remove the positive cable next, and lay the cables where they can NOT touch one another or anything else in the compartment as there MIGHT be some residual electricity left in the system. Next remove anything which will block the battery from coming out of its' hole, then replace it with the same capacity or greater battery. To reinstall simply reverse the above procedure. Once you have the new battery in the hole, THEN and ONLY then hookup the positive cable FIRST, after it is completely secure then hook up the negative cable, finally reinstalling the fender brace (It is NECESSARY! do NOT leave it off just because it is a pain in the butt to mess with.) There was also a sortta felt cover/lining/ what ever around the battery when you pulled it out. IF it is NOT damaged beyond recognition, put it back also. Once you have the battery all nice and tucked in, you will have to reset your clock and radio presets. Good luck, if you follow the above processes, you should have no problem succeeding!

Between the air filter and the throttle plate.

LS and Lt have 6.5" in the front and 6x9" in the back.

do you have an aftermarket head unit? Either way, you will need a wiring kit. Depending on what size your amp is, you may need a capacitor as well. Brands such as Scosche and EFX are 2 cheaper brands, but seem to work just as well for less cash. Expect to pay anywhere from $10 to $120 (+) depending on the quality and length of the wires.

Car and truck parts are not even close to being the same as far as the drive train.

Won't work.

there should be a square hole in the tensioner arm that you use a breaker bar and an extension in the hole and just turn the tensioner whatever direction that will loosen the belt.

It is probably the lifters. I would try some oil addative for sticking lifters and let it stay in there for a couple of weeks and see if that helps. low on oil? until the oil is warmed up enough to flow freely it could make that noise if low on oil. a 2004? i'd take it back to the dealer, that is to new to have ANY problems. good luck TAKE IT TO THE DEALER, IF IT'S A 3.4L AND THEY TELL YOU IT'S NORMAL COLD START PISTON SLAP, THAT'S WHAT IT IS. THEY ALL DO IT. IT'S NOT A BIG DEAL, OTHER THAN INTAKE GASKETS, IT'S A VERY DEPENDABLE ENGINE.

need to know how to open the door from the outside of a previa 1992 to take off the panel

While the ignition is in the ON position, follow this sequence:

Turn your headlights to the parking position and then OFF 3x's.

The 2007 Chevrolet Impala runs on flex-fuel (FFV).

You need to purchase a Haynes Manual for you particular car. It will be a great investment if you plan to work on your own car.

To reset the Check Engine Light you must go to the trunk of your car get a cro-bar and smash the dash board until the light doesn't come on no more...

should be drivers side of the radiator at bottom. I recommend just pulling of the lower radiator hose, i have seen numerouse petcocks break off, they are not worth the risk

i have a 2005 impala with these issues and five local tranny shops looked at my car and said its a common problem with (1) the valve body design, (2) weak clutch plates and (3) faulty solenoids. ... basically U need a rebuilt or remanufactured tranny ... DO NOT simply replace the tranny with another because it will have the same faulty parts inside that failed the first time ... U must have it REBUILT with AFTERMARKET improved parts because the standard stock parts will fail U again... hope this helps..... Sean G.

1000lbs

The charger will win this quarter mile race.

tell me where is the egr valve located please

the egr valve is usually located on the top right of the intake manifold on top of the engine so if your facing the engine, look down to your right