Daewoo Nubira

you remove it by taking the whole panel off - it is a moulded piece which is integrated into the door panel. there are small plastic screws - 2 located on the side of the panel and two located on the opposite side of the panel - just undo and carefully take the panel off. There is also a screw by the buttons for the electric windows. Hope this helps

Moving clockwise starting at the Alternator pulley - over power steering pump - down under compressor pulley - over to torsional damper - around damper to auto tensioner - around auto tensioner - back to alternator pulley.

i need how much pression (torque) for head daewoo nubira 2001 2.0

I have daewoo nubira 2001 year. please help me about unlock the radio in my car.

Yes, it is. You can see the slot just in top of radio display. You need to place a CD (label faced up) into this slot and gently push it in. The CD will be automatic turned into the slot and after few moments will be played.

I have a 1995 Excel, found mine at the back of the stereo. Yeah i know...strangest place to put it but that's where it is. Should be a 4 digit code

I don't know if this will help but I had to find the stereo code for a ford once and ended up having to ring head office with the vin number of the car to get it. That is assuming of course that the stereo is factory installed. Otherwise check anything that was in the car when you bought it as someone could have written it on a manual or such. Hope it helps.

Have vehicle scanned to determine the problem

Hi All

I have just replaced the electric window mechanism in the RR door of a 1998 Daewoo Nubira.

You will need 1 x Phillips head screw driver -preferable with a small diameter shaft

Remove the 4 plastic screws from the door panel

Remove the plastic fitting on the door handle-Attention is required here as damage can occur quite easily. There are 3 plastic clips that hold the door handle surround use a small flat blade screwdriver to gently loosen clips located centre of fitting towards the rear of vehicle and top and bottom about 5 cm in from the leading edge, Now remove the electric window switch with Phillips head screwdriver ,slide switch towards the rear of vehicle to remove, Un-plug switch cable. Now you can remove the door panel ,lift panel upwards from the rear. Now you will need to remove the 2 Phillips head screws that hold the door arm support bracket once removed you can gently remove the protective plastic you will see there are 7 x 10 mm nuts that hold the assembly on remove all of these nuts next step is to remove the 2 x Phillips head screws that hold the glass onto the electric window mechanism, I did this by drilling to 6 mm holes in the door panel as close to where the screws are located (as I could NOT lower the glass) and removed screws -use a large flat blade screwdriver to pry window assembly inside the door between door and mechanism at the top 2 nuts, it can now be removed by gently prying downwards -Good Luck Hope This Helps

I have a 2000 Daewoo Nubira and I had the control arm replaced and it fixed the problem.

If the transmission is electronically controlled - Dexron III, and if manually controlled - Dexron II. If there is no 'dip stick' for testing the fluid level, then the transmission is probably electronic control.

You can program without having the codes by following these steps:

1. Turn on the TV (or other device).

2. Press and hold CODE SEARCH until light stays lit; release.

3. Press TV button.

4. Press POWER button repeatedly until TV turns off.

5. Press Enter.

Repeat for each device.

These instructions are found on the inside of the battery cover.

Is your timing belt broken?

This worked for me: open the car with the door key. Sit in and shut the door. Now operate the door lock using the lock tab on the drivers door four times very quickly ((lock then open four times). Press the close button on the fob. If the door locks again, you've done it. May well work for other cars too.

The code is individual for each car, and the code is located in your owners handbook.

Inside the Oil Pan.

Step 1: Open the ashtray and remove two screws pointing upwards in the upper corners of the recess. Step 2: Unclip the fascia panel around the radio and heater controls. Step 3: Remove the lefthand screws securing the heater matrix.Step 4: Locate the bracket with these two screws so that it locks both the arm and plastic in place. Step 5: Replace the fascia panel and the ashtray.

Really need more info (engine size, model, type, etc..) A 1.6L DOHC, should be located about 9'o-clock if looking at the Crankshaft pulley through the right side wheel well. Just FYI the camshaft sensor is located under the timing belt cover between the two camshafts (1.6L DOHC) but behind the exhaust cam gear (gear towards front of car).

If all of them have spontaneously gone out then it is likely a blown fuse. Look in the fuse box for hazard lights and pull the fuse out with the fuse puller. Then replace it with one of the same color (and probably the same number on the top). However, if your fuse is blown, there is usually a reason, which will cause it to soon blow again. There could be a short in your wires somewhere. But just replace the fuse and if it keeps happening then look into it more closely.

The oil pump is located behind the harmonic balancer, it has the oil filter attached to it and it is quite a major job to remove.

i believe you need to buy a comlete new break switch.if the lever on the break switch is vertical to the floor,i think it might be bad.

I just drained my coolant and it was the green stuff. There are only two kinds and one of them is red (orange), and one is green, which is supposed to be a long lasting universal one or something. Anyway, buy the green stuff.

Usually in front of the radiator

Under the timing belt cover, sensor runs of tooth wheel on timing belt crank cog. job and a half.

co adjust error

it means nothing..... It is only there to look cool and make people think that you have a alarm on your car (anti-theft properties)