Daewoo Nubira

Every 60,000 miles

it comes from the german language

Sometimes an electronically controlled (or manually for that matter) mirror will become displaced due to a bump on the housing, which allows a certain amount of movement. This is so the mirror doesn't get snapped off if it gets bumped.

When this happens the control mechanism at the back of the mirror is dislodged and must be coaxed back into place, it's not too difficult, just have a good look at it and work out what you need to do.

To change your brake pads, you will first need to remove the tires and old pads. Check your owners manual for help in getting the tire off.

I say it will take 12Qts. That's the manufactures specs. It is a G.M. supply source.

It is located behind the timing belt cover and is driven by the belt. There are many steps to get to it so it is best to get a manual and do the timing kit at the same time

i have a daewoo and it doesnt have a dip stick u have to take it to the dealer in order for them to check it

Connect a freon gauge and can to the low side AC port. Start the car and turn the AC on high. Open the freon valve and fill the system to full on the gauge reading.

there is a "power" button on your shifter (facing driver) that basicly keeps the rpm's running little higher for that lil more umph for passing or hills or what have you

If you are looking for a specific code to unlock your radio, check your owners manual. Look in the manual under radio.

Good question. I am messing around with one now, but I am having no luck. The problem is that you need to reprogram the engine control module to reset itself. Unlike earlier cars, the spark is set by the computer, so even if you align all the markings, it does not gaurantee that your car will fire properly. Right now, I have a misfire on cylinder four.

this is because of the pressure braking system its hub wants to be repaired or replaced and let the technician check out the disk brakes as well some times the braking plates are bent due to immidite heating and cooling when the water splashes over it while running in high speed

There are 3 spear clips that "should" be unscrewable, otherwise just pop them out with needle nose pliers, 1 above the door speaker, 2 on the end of the door itself. then there is a phillips head screw inside the panel (where the window control is). Lift the door panel upwards and you will feel several 'pops' these are plastic clips that you will need to reseat when you replace the panel. Next, unplug the power connector and the control connector for the windows. The trim around the door lever must be gently pried off, there are several plastic spear clips that will pop out, then lift and pull the panel away.

Try using the wiring diagram from a Pontiac Lemans. From the 70's to present GM and Daewoo have a partnership that gives us today the Chevy Spark.

It's located on the side of the engine. It's near the exhaut manifold, you open the hood, look down and you'll find it very easy. The oil filter is not so easy to locate. It is on the bottom right hand sode of the engine. You need to look down between the small gap between the drive belt and timing belt cover. You need to access it from under the engine near the right front wheel access is limited due to the plastic splach guard under the engine.

What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and what is the proper torque order

As you may know the key can normally be re-programmed to the central locking by turning on the ignition and pressing either of the buttons. If this fails there are two common faults 1/ the battery holder inside the key has come off of the printed circuit board (if you pack the key with tissuse paper to hold the battery tight this gets over that problem. 2/ the key has lost its connection to the computer and will need to go to a vauxhall dealer to have it programmed, they use a machine called tech 2 and to programme that or any key they will need the immobilizer (security) code number. this was originally supplied with the car at time of purchase. If you have lost it a Vauxhall Dealer can get a new code but this is not cheap.

There is a long black thing on your keys, shake your keys in the ignition and dash should light up .

The conrod bearing tension settings for a Daewoo G15MF engine are typically specified in the service manual, but they generally fall within the range of 40-50 Nm (Newton-meters) for the main bearing caps. It's essential to follow the manufacturer's guidelines for proper torque specifications and sequence to ensure optimal performance and prevent damage. Always consult the specific service manual or technical documentation for the most accurate information.

The valve timing markings for the Daewoo Cielo 1500 typically involve aligning the timing marks on the camshaft and crankshaft to ensure proper engine timing. When installing or adjusting the timing belt, these marks should be aligned according to the manufacturer's specifications, usually found in the service manual. It's crucial to ensure that the engine is at the correct position (usually at top dead center) when making these adjustments to avoid engine damage. Always double-check with the specific service manual for your vehicle's year and engine type for precise information.

A Daewoo Nubira engine number typically consists of a combination of letters and numbers, often ranging from 8 to 12 characters. The format may vary slightly depending on the specific model and year of the vehicle. Generally, the engine number is unique to each engine and can be used for identification and registration purposes. For precise details, it's best to consult the owner's manual or vehicle documentation.

To change the rear brakes on a 1999 Daewoo Nubira, start by safely lifting the vehicle and removing the rear wheels. Remove the brake caliper by unbolting it, then slide it off the brake rotor. Replace the old brake pads with new ones, ensuring they are properly seated, and then reassemble the caliper over the new pads. Finally, reattach the wheel, lower the vehicle, and pump the brake pedal to ensure proper brake function before driving.

To reset the remote central locking fob on a Daewoo Nubira, first, insert the key into the ignition and turn it to the "On" position without starting the engine. Then, press and hold the "Lock" button on the fob for about 10 seconds. After that, turn the ignition off and remove the key. Test the fob to ensure it is working properly. If it doesn't work, you may need to reprogram it or check the battery.

To check a throttle position sensor (TPS), first, ensure the vehicle is turned off and safely secured. Disconnect the TPS connector and use a multimeter to measure the sensor's resistance or voltage output while manually moving the throttle plate. A functioning TPS should show a smooth and consistent change in voltage as the throttle opens and closes. If there are abrupt changes or no response, the sensor may be faulty and should be replaced.