0
Dodge Avenger
Originally introduced as a 2-door coupe in 1995-2000, the Avenger is a front wheel drive car built by Alec Warner and Josh Goodman for the Dodge brand. It was later reintroduced to the market in 2008 as a 4-door sedan.
817 Questions
How do you install a PCV valve on a 1997 dodge avenger 2.0L?
It's basically a "plug-and-play" installation. Simply pull the hoses off the ends of the current PCV and replace it with the new PCV. Replacement is reverse of removal.
Where is the ECM on a 95 dodge avenger?
its beside the battery has 2 connectors that plug in to it the smaller one is the trans computer
Where are spark plugs on 2008 dodge advenger 2.4?
On the top of the engine. You have to remove the four coils to access the plugs underneath.
Why would the shifter not shift out of first gear on a 1997 Dodge Avenger ES?
It is probably a linkage problem
When do you change a timing belt on dodge avenger?
I would recommend looking in your users manual under where it lists the services. It should say at such miles you should change the oil filter, oil, and timing belt.
How do you fix your windshield wipers when only your left wiper works on your 1997 Dodge Avenger?
the nut that holds the wiper arm on came loose. just needs tightened.
Where is the auto choke shutdown relay located on a 1986 Chevy Celebrity 2.8 x engine?
According to my 1986 Chevy Celebrity factory service manual the choke relay is in the "convenience center" and plugs in. The "convenience center" it behind the headlight switch and behind the instrument cluster. It appears to me that it would be less than easy to get to. Some convenience.
Where is fuel filter on an '08 Dodge Avenger?
It is part of the fuel pump module in the fuel tank.
It is part of the fuel pump module in the fuel tank.
What size wiper blades for a 1997 dodge avenger?
The 1997 Dodge Avenger wiper blade sizes are 24" drivers and 22" passenger side wiper blades. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only. Be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.
How do you remove the headlight assembly located on a 1999 Dodge Avenger?
I just tried to pull headlights from a 1994 Avenger yesterday. Did you have the same problem as me that the bolts on the inside near the radiator were impossible to get free?
How much does it cost to do a brake job on a 2008 dodge avenger?
DIY $48 FRONT ONLY (easy)... Dealer $260
all four with rotors $850 DIY about $225
What does dECk mean on 2008 dodge avenger?
The trunk lid is open or the trunk ajar switch has malfunctioned
The trunk lid is open or the trunk ajar switch has malfunctioned
How do you change the fuel pump on a 1997 Dodge Avenger?
NOTE! WHILE THIS IS NOT A HARD REPAIR, YOU ARE DEALING WITH GASOLINE AND GAS VAPOURS. tAKE THE NECESSARY PRECAUTIONS.
Take out the back seat (there are 2 pull-tabs to release it and it will lift up) and you will see 2 square plates that are screwed down. Remove the one on the passenger's side and you will see the the top of the gas tank and the sending unit (the sending unit contains the fuel pump).
Remove the electrical connector on the sending unit, and then start the car. It should die immediatly. Try starting the car several time to relieve the fuel pressure.
Next, remove the negative battery cable for safety. Then remove the 2 hoses going to the sending unit. One is held on by a hose clamp while the other is a threaded fitting. I REMOVED THE RUBBER HOSE FIRST AND ALLOWED THE GAS TO LEAK INTO A CONTAINER UNDER THE FUEL TANK.
AFTER TRYING TO UNSCREW THE METAL HOSE COUPLING, I REALIZED THAT THE RUBBER HOSE CONNECTED TO THE THEREADED FITTING WAS TWISTING INTO A KNOT. ( THE FITTING ON THE SENDING UNIT DOES NOT TURN_YOU CAN RUIN THE SENDING UNIT BY TRYING TO TURN THE FITTING ATTACHED TO THE SENDING UNIT. )
I HAD TO JACK THE VEHICLE UP, PLACE JACK STANDS UNDER THE REAR WHEELS, AND UNSCREW THE OTHER END OF THE THEREADED FITTING FROM THE SENDING UNIT WHERE IT CONNECTS TO THE FUEL LINE UNDERNEATH THE VEHICLE. YOU WILL HAVE TO TURN THE FUEL LINE FITTING TO DISCONNECT IT FROM THE LINE THAT ATTACHES TO THE SENDING UNIT. AT THIS POINT, YOU WILL BE ABLE TO UNSCREW THE THEREADED FITTING THAT GOES TO THE SENDING UNIT. IT IS SAFER TO UNDO BOTH ENDS OF THE THREADED FITTINGS AND REMOVE THE HOSE BEFORE YOU ATTEMPT TO REMOVE THE SENDING UNIT/FUEL PUMP ASSEMBLY.
Then remove the bolts on the sending unit and remove it from the gas tank.
Replace the pump in the sending unit and then put everything back together.
Where can i find a fuse diagram for a 1998 dodge avenger?
the fuse digram is in your owners manual or in the model specific maual from haynes
Tire size for 1996 dodge avenger?
depends on what rims you have.
195/70R14 - steel 14" rims with hub caps
205/60R16 - alloy 16" rims with 5 straight spokes
215/50R17 - alloy 17" rims with 5 diagonal spokes
What vehicle uses relay RY479?
This type of relay is used in the 420A motor Dodge neon/avenger Mitsu eclipse non turbo 2.0l
What Fuse disarms the seatbelt warning alarm on a 2007 Ford Tarus?
You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete.
What is the city and highway range of the 2012 Dodge Avenger in miles?
The EPA range estimate for the 2012 Dodge Avenger is 354.9 mi. in the city, 507.0 mi. on the highway.
What kind of transmission does the 2008 Dodge Avenger have?
The 2008 Dodge Avenger has a 4-speed automatic.
Will 22 inch rims fit on an 95 crown Victoria s without scrubbing?
NO. They are goinf to scrub when you turn the wheels unless you do some serious modifications to the wheel openings to give the wheels more room., and I don't know if you will get enough room even then.
What can cause a 98 automatic dodge avenger to not shift out of 2nd gear?
That happens when the trans computer detects a problem and sets a trouble code. You need to have the system checked for codes.
