answersLogoWhite

0

🚗

Dodge Caravan

The Caravan is a minivan produced by Chrysler Group LLC for its Dodge brand. Since its introduction to the market in 1987, this long wheelbase (LWB) vehicle was manufactured in five generation models.

4,933 Questions

How do you locate the tcm on a 2000 Dodge Caravan?

If you have a 4-speed transmission, it is under the hood on the passenger side inner fender next to the washer fluid reservoir. If it has the 3-speed transmission, it doesn't have one.

How do you change the an Air Condtion filter on a Volvo V70 2004 Model?

Check the Bosch instructions online for their P3857 filter. The post 2001 V70 cabin air filter (sometimes called a "pollen air filter") is accessed by removing a trim piece below the glove box.

How do you replace heater core on 2000 dodge caravan?

You need to recover the R134 charge, remove the whole dashboard, then remove the a/c heater box to get to the heater core.

The heater core should be accessible right next to the gas pedal. No dash removal is necessary.

How do you fix your turn signal if it works when you turn the hazards on but it does not when you want to turn?

You need to replace the turn signal relay. It should be right next to the hazard (emergency) relay. Turn on the hazards and follow the clicking sound under the driver side dashboard. Once you've located it, if you touch it you can feel the hazard relay working. The other relay is for the turn signal. It's a small round canister. It's just a matter of removing and replacing.

I had the same problem with my 97 Accord. My hazards worked, but the turn signals did not. I thought it was actuallly the signal arm. In the end, it had nothing to do with the signal relay, arm, or bulbs. I just changed a fuse located in the fuse box next to my brake pedal (it was bruned out) and it worked. I don't know what kind of car you have, but if it's a Honda this is probably the problem.

What would cause a clicking noise most notable when in Park and Neutral and oil and transmission level are fine?

a clicking sound usually indicates a small exahust manifold leak or a noisy hydraulic lifter in engine if no exhaust leak, check to see you are using correct viscosity oil and a good brand, not a cheap recycled brand such as you get at walmart

Why did Dodge stop making the Caliber?

It was replaced by the brand new Dodge Dart.

Where is the expansion valve located on a 1999 dodge caravan?

It is located on the firewall next to the alternator. The rear valve is attached to the rear heater/AC unit if so equipped. To replace the front one disconnect the battery, then just remove the 3 bolts on the mounting bracket, loosen the bolt holding the alternator and move it out of the way. Unbolt the high side hose bolt and hose, remove the lowside hose, remove the 2 little torx bolts and pull off the expansion valve, and reverse to install with new o-rings coated in pag oil.

To replace the rear valve remove the D Pillar trim panel from the passengers side rear by pulling it off and removing the seatbelt bolt. Next pull the carpeted panel covering the speaker off ( Just pull ) . Remove all the Phillips screws you see and remove the panel covering the rear Heat/AC unit. Unbolt the rear Heat/AC unit, unbolt the the AC hoses that come into the van from under the rear (4 bolts in all) , unplug the electrical connectors and lift from the rear on the unit and pull it out far enough to get at the expansion valve. Unwrap the valve from the black gooey tape, unbolt it and pull it off. Re-install new o-rings, and reverse.

How do you know if your 1991 dodge caravan is a 3 speed or 4 speed transmission?

The dash indicator will have the "D" circled for a 4spd. The 4spd dash will read PRND3L The 3spd dash will read PRND21

What are the advantages of a Teardrop caravan over a more traditional model?

A "Teardrop" caravan derives its name from its tear-like shape. The advantages of this type of caravan over a more traditional model include comfort, water-resistance, better storage, no set-up needed and ease of to pulling because of it shape and weight.

Horn and left turn signal do not work are they connected somehow and can I fix the problem.?

Have you checked your fuses? Does the turn signal light up at all? If it does, you most likely need to replace a flasher.

Does Dodge use an inertia switch?

Dodge doesn't use inertia switches. The fuel pump is controlled via a relay by the computer.
Dodge does not use inertia/reset switches

How do you repair a drivers side power window of a 2001 dodge caravan which has fallen into the door?

Remove the inside door panel. The entire power window mechanism will be visible. Put the window back onto the window track.

Rear Wiper blade size for Dodge Caravan 1999?

The 1999 Dodge Caravan wiper blade sizes are 28" wiper blades on both sides front and a 18" rear wiper. Do not buy by length only though. See the Sources and Related Links section below for more information. Since there are over 22 different wiper arm attachments - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.

Where is the iod fuse in a 2003 dodge caravan?

All fuses are under the hood, next to the battery. The lid has a diagram of locations.

Is dodge caravan 3 liter engine made by Mitsubishi?

It was a Mitsubishi design, but I believe Chrysler built them.

It was a Mitsubishi design, but I believe Chrysler built them.

Why would rear heat in van work but front heat don't get hot?

Because the rear heat and front hear are 2 different systems. If for example the front heater coil has broken the rear one may still be functioning.

Front heater core could be plugged up. Try flushing it out.

How do you replace the headlight assembly located on a 2000 Dodge Intrepid?

look in the users manual for the instructions on replacing bulbs. it's the same because you have to remove the assembly to replace the bulbs there are 2 jack screws , on the top of the assembly, one on each side. remove them and pull the assembly out towards the front of the car. remove the lights put the lights in the new assembly. put the new assembly back in and replace the jack screws. you will need to adjust the lights.