answersLogoWhite

0

Dodge Durango

The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.

3,297 Questions

What is the wheel base of the 2013 Dodge Durango?

The 2013 Dodge Durango has a 9 ft. 11.8 in. (119.8 in.) wheel base.

What is fault code no BU5 on a Dodge Durango?

This fault code appears in the odometer display (at least it did on mine). It's actually "no bus" as in no communication "bus" (a computer term for a data route). What it is saying is that the dashboard sub-computer is not communicating with the main computer (PCM) which is located on the passenger side of the engine compartment, bolted just above the wheel well area. Check the 3 connectors to see if they are plugged in all the way. If they are, your PCM is probably bad (mine lasted 90k miles). This is something you can't replace yourself because the new one must be programmed with the milage and VIN and other info by MOPAR before it's installed. Be careful, because when the PCM fails, your money pit (Durango) will start to suddenly stall at the worst times (Freeway, Boat launch, stop light on a one lane road) and not restart until you disconnect the battery for 10 minutes and then reconnect. Good luck! The dealer charged me $800 to replace mine. $500 for the part and $300 to diagnose the problem. And I told them it was a bad PCM when I brought it in. No need to go to a dealership if it is the PCM... you can purchase refurbs on the web from $199 and all you have to do is supply the VIN, milage and a couple of other things so that it can be programmed correctly and sent back to you so that you can install yourself... some sites also offer a warranty benefit if you send your old unit in for remanufacture. Just use a search engine with key words like "2002 Dodge Durango, PCM" Ted

Can rims for 99 Dodge Durango go on a 2004 Dodge Durango?

No Chance! the different bodies have a different number of lugs and different bolt pattern

Where can you find a diagram for the braking system on a 2003 dodge durango?

eBay has everything you should try there. if not, yahoo or bing might lead you to what you are looking for. i hope this helped.

2002 dodge durango won't go out of park?

The solution to your problem may be as simple as depressing the brake pedal to release the shift lever. If you're parked on a hill it could just be jammed. You'll need to release the pressure on the parking gear by moving the vehicle a little. be carefull good luck.

How do you slim Jim a 1999 ford f 150?

You have to go four or five inches from the edge of the glass, but I fid it`s better to use a metal coat hanger to open door.

Why will none of the power windows in my 2005 Dodge Durango not work?

You might have pushed the window lock button which will cause you to not be able to open any of the windows. You might also have a bad computer which is getting old and needs to be thrown away

How do you replace a positive battery cable on a 2002 durango?

Replacement of automotive positive cables is pretty much the same for all vehicles, so this answer will be generic in nature. Safety first ALWAYS. Any time one is working on a vehicle when there is even the slightest possibility of a tool coming into contact with a "hot," electrically energized conductor [wire, terminal post, bare connector, etc] it is imperative that the entire electrical system be disconnected from the battery FIRST. The safe way to do this is to first remove the NEGATIVE cable clamp from the battery negative terminal post by loosening the bolt on the cable clamp, and lifting the clamp off. Tension in the negative cable may cause the clamp to move back into contact with the terminal, so it is important that the cable be moved so that it cannot accidently recontact the teminal while you are working. Then loosen the positive cable terminal clamp and remove the clamp from the battery terminal post. Next, follow the positive cable to it's other end. There will be some type of connector [usually a metal "eyelet"] connected to an isolated solenoid or positive buss terminal bolt. With a properly sized wrench, loosen and remove the cable from the terminal bolt. IF the threads are dirty or corroded, removal will be easier if you first clean them with a small wire brush, and apply a small amount of penetrating oil, or something like WD-40. Install the new cable in the reverse order of above instructions. IF you have alternate transportation available, I recommend that you remove the old cable first, and take it with you to the auto parts supply store in order to make sure that you get the exact same replacement cable on the first trip. If you cannot do this, then when you get the new cable, take it out to the parking lot, raise the hood, and match it to the old one.

Where is the fuel pump and filter located in a 1990 Volvo 240?

Fuel pump in the rear of the car.. from underneath... when the car is on a lift. the filter is a canister near the pump.. costs about 15 or 20 bucks online... look in places like thepartsbin.com

What is the drivetrain warranty on the 2003 Dodge Durango?

The drivetrain warranty of the 2003 Dodge Durango is 7 yr./ 70000 mi..

What means check cages that comes up on your dashboard when motor stops running while driving?

anyone help me understand what does it mean check gages light on dashboard.

Answer: It means to look at the guages, something is out of the ordinary range, even the fuel level being low can cause this "Check Gauges" not the Check Engine light to come on\.

How do you change the heater core on a Dodge Durango?

Remove the instrument panel using the following steps
  1. Disconnect the battery negative cable.
  2. Remove the trim from the sills of both doors.
  3. Remove the trim from the cowl side inner panels on both sides.
  4. Remove the steering column opening cover.
  5. Remove the inside hood release latch.
  6. Disconnect the overdrive lockout switch, if fitted.
  7. Remove the steering column. Do NOT remove the air bag, steering wheel or switches. Be sure the steering wheel is locked and secured from rotation to prevent loss of clockspring centering.
  8. Detach the parking brake cable and switch.
  9. Disconnect all accessible wiring harness connectors, ground wires, headlight wiring, sound system, etc., from the instrument panel.
  10. Disconnect the vacuum harness connector on the left side of the heater-A/C housing.
  11. Remove the center support bracket from the instrument panel.
  12. Remove the ACM ground line. Disconnect the ACM harness.
  13. Remove the glove box.
  14. Disconnect the radio antenna.
  15. Disconnect the blower motor wiring harness.
  16. Disconnect the speakers.
  17. Disconnect the radio ground wire.
  18. Loosen the right and left instrument panel cowl side roll-down bracket screw about a quarter of an inch.
  19. Remove the screws that secure the top of the instrument panel to the top of the dash panel, removing the center screw last.
  20. Pull the lower instrument panel rearward until the right and left cowl side roll-down bracket screws are in the roll-down slot position of both brackets.
  21. Roll down the instrument panel and install a temporary hook in the center hole. Support the panel.
  22. Disconnect the remaining wiring.
  23. Disconnect remaining hoses.
  24. Remove the panel.
  25. If the vehicle is equipped with A/C, recover the refrigerant. See "Note" above.
  26. Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube.
  27. Disconnect the accumulator inlet tube.
  28. Drain the cooling system.
  29. Disconnect the heater hoses from the heater core tubes.
  30. Remove the nuts from the heater-A/C mounting studs on the engine compartment side of the dash panel.
  31. Remove the nut that secures the heater-A/C housing mounting brace to the stud on the passenger compartment side of the dashboard.
  32. Pull the housing rearward far enough for the mounting studs and evaporator condensate drain tube to clear the dash panel holes.
  33. Remove the housing from the vehicle.
  34. Installation is the reverse of removal.

How do you fix an evaporative emission control system leak in a Dodge Durango?

The most common leaks come from 5/16" vacuum lines that go from the evaporative purge solenoid to the intake manifold. If you look on the driver's side fenderwell, you will see the main fuse box. In front and under this black box, there are two lines that run to the engine. These lines get brittle with age and crack and leak. Sometimes you can listen top the engine run with the hood up, and actually hear the leak and pinpoint the source.

Also check the hoses in front of the fuel tank underneath.

When do you replace the timing belt on a 2000 Dodge Durango and about how much should it cost?

NO Belt !It does not have a belt. It has a chain which should last the life of the engine.

**** Actually it has 3 different timing chains. and i have gone through 2 durangos(2001, 2002) both with the timing chains needing to be replaced.

Lost the key fob to my 99 dodge durango still have the key but no fob Anyway to override the alarm andor ignition kill switch so I can operate the vehicle It's a factory alarm?

Obtain a new key/fob from the dealer. Disarming all of this seems to be counterproductive since most of it prevents theft of the entire truck. Losing the fob

is small stuff comparatively.