0
Ford E-150 Van
The E-150 belongs to Ford’s extensive product line of full-size passenger and cargo vans. Also known as the Traveler, the E-150 features excellent design and a roomy interior for passengers and baggage.
2,051 Questions
How do you remove the fan clutch from 1992 Ford E150 van 6-cylinder?
The 4.2 Liter and 4.9 Liter, 6 cyl engine, both have one large nut holding the clutch assembly onto the water pump.
Remove the radiator shroud.
You need two wrenches, one goes behind the clutch to restrain it from turning, and the other wrench removes the nut on the front of the clutch shaft.
It is a two man job, with one person under the vehicle restraining the shaft, and the other person on top, removing the nut.
You may have to remove the fan first, to get access.
You man have to remove the upper radiator hose on some models.
Anwhere you can access a Fuse box diagram for 1998 ford econoline 150?
It's in the "roadside emergencies" section of the owners manual. Save yourself a trip to the junkyard as suggested below and download it for free at
http://vehicleownersmanuals.blogspot.com/2009/09/ford-econoline-e-150-e-250-e-350-owners.html
Most of these type questions would never be asked if driver's would open their owner's manual and read. This type information is contained within the owner's manual. If you do not have one, get one. You can get one at your dealer, or may find one at a salvage yard, laying in a glove box. You need the owner's manual for maintenance intervals, and other pertinent information. Why and how thee seem to be lost is a mystery to me. Question after question, asked on this site that can be answered by opening this little book. I have never owned a vehicle without having an owner's manual. I also see a lot of questions that can be answered by raising the hood and looking at the placards located there. Spark plug gap is just one. Amazing!
The fuse panel is under the dash behind the brake pedal.
Where is the thermostat located on a 1987 Ford E150 Van?
There are 3 different motors listed for the 87 E150 Ford van. The 4.9 the 5.0 and the 5.8 all have the thermostat located where the top radiator connects to the motor in the housing that the hose connects to. It will be under the inlet on top of the engine block.
Replace heater core 1987 ford e150 van?
Remove the water supply hoses from your 1987 Ford E1 50 heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.
How do you remove a driveshaft from a 1998 Chevy S10?
- Safety First. Block the tires and set the e-brake so it can't roll in any way. (most important if you are not on level ground.)
- Locate the correct tools for the job. (i.e large flat tip screwdriver, wrench's, oil drain pan (to catch trans fluid if an automatic), and your favorite sheet of cardboard)
Be ready to catch the drive shaft as the following steps will free it and it could escape ;-).
You have what is known as a hanger bearing in the center. Now there are four bolts that hold the rear shaft to the rear axle. Simply remove the bolts and nuts. Once the rear bolts are removed you should be able carefully pry the rear section forward a bit so it can drop down, now to side the rearwards and it should separate. Now remove the hanger bearing and the front shaft should slide rearward as well. Make sure the oil pan is in position and ready to the small amount of fluid you will lose when you pull the collar out the back end of your trans.
If you have a manual transmission it will necessary to remove the bolts and nuts on the other end of the drive shaft up next the trans.
What can you use other than dealer item to replace the hose on 96 E150 fuel filler neck?
The hose is 1 1/2" ID X 11" long. Use fuel hose, NOT a radiator hose. This is available at most auto parts stores for about a dollar an inch. The job should take less than an hour.
How do you change the spark plugs on a 1999 ford e 150?
Well, to be blunt, with difficulty!! If it's a 5.4L V-8, you MUST WAIT UNTIL THE ENGINE IS STONE COLD (sitting without being started overnight or for at LEAST 8-10 hours). Any engine with aluminum cylinder heads NEEDS TO BE COLD or you'll strip the threads in the cylinder head. Next, you'll need to remove each individual coil pack (one per cylinder) using an 8mm socket. If you can't get to the coil pack(s), you'll need to remove components on the engine to get at them. Also, you'll need to remove the engine cover ("dog-house") inside the van which is fairly easy to gain access to the rear plugs. If it's a V-10, the same procedure applies. Once the coil has been removed, you'll need to spray a small amount of penetrating lubricant into each spark plug hole BEFORE attempting to "break" each plug free. Once plug is "broken free", an additional squirt of penetrant (NOT WD-40! Use PB Blaster if available, or equivalent), then GENTLY unscrew each plug, a little at a time; sometimes it helps to twist out slightly, squirt with penetrant, then work the plug back and forth until it feels smooth. If not, you'll strip the threads in the aluminum cylinder head and you're pretty much done-heli-coils DON'T WORK. It's NOT an easy job to undertake.
What is the firing order for a Ford Econoline 150 6 cylinder 4.9 Liter engine?
firing order 153624.......rotation is clockwise
How do you change the oil pressure sender unit on an 1989 Ciera Cutlass?
Unplug it, then unscrew it, then install a new one. A special tool is available that's basically a bent-up 9/16" wrench.
How do you change ignition switch on a 1992 econoline 250 ford van?
best to go to a experienced mechanic-one who deals with auto keys
there are wired involved
How do you replace the rear door latch of a 1999 ford E150 van?
Drill out the two screws that hold the latch bracket. They are fat screws, so use a 1/4 inch bit in the torx holes. I just did this, and was finally able to open the piece of crap door that ford built. they use 1950s technology on 1990s autos. check out their retro interior light reostat.
You installed a new sterio radio in your 1994 ford e150 and now your speakers do not work any ideas?
You must connect the blue remote wire for the speakers to work
How many quarts of oil does the 1998 ford E-150 van take?
5 qt's . I have owned this model for 5 years and love it. Highly recommend using Valvoline Max Life ( in the red container).
Why does the Air Conditioner compressor keeping going bad on a Ford E150 Van?
Not evacuated totally or properly prior to charging? Not charged properly - too much freon Oil not added when charged? Defective compressors?
It's probably the idle control solenoid
someone probably got a little water in the the module it may work after it dries out...it may not
Where is the fuel pump relay and inertia switch on a 1986 E150 with 302 engine?
driver side next to brake under carpet. * Mine is on the passenger side; under dashboard and has a white RESET botton on the top.
Back the van up on ramps then crawl in from the side under the filler door and reach up and remover the hose clamps using either a screw driver or ¼" socket set. The one near the fuel door is the easier one to remove and you will have to feel your way on the one on the tank. Once you have the clamps off you will need to try to wiggle the hose until they come loose from the metal pipe. You can also reach up and use a utility knife to cut the hose length wise then peel the hose from around the metal filler pipe. Beware that the dealer price on the Ford hose is about $90.00. If you only have one crack at the fill end you may want to consider cleaning the pipe good with some rubbing alcohol and seal with the black RTV silicone caulk that you can purchase at any automotive supply store. Good Luck!
What grade of gasoline should be used for the 2001 ford econoline 150?
For a 2001 Ford E-150 :
The gasoline engines use ( " regular " unleaded , 87 octane )
