0
Ford Focus
The Ford Focus is a compact family car produced by Ford. It was initially introduced in Europe in July 1998, then entered the global market in February 2000. To date, there are more than 9.2 million Ford Focus sold worldwide.
4,083 Questions
Where is the fuse for electric door locks located on 2000 Focus?
It is on the the fuse panel located behind the dash to the left of the steering column. It is Fuse # 63 and it is on the BACK of the fuse panel. You have to unfasten the fuse panel from its mounting to get to it. A BAD design flaw. There are two hex-head screws that I can see. Behind all that good stuff?
Cant select first and third gear in ford focus how to fix?
Your shifter is out of alignment. The arms need adjustment. Get a Repair Manual at NAPA, or Auto Zone, and follow the instructions.
Why is your 6 disc CD stereo display blinking on your 2002 ford focus?
I believe that is an anti-theft device, there is a thin peice of plastic that when you push a button it pops off and when that happens, you can't turn on the CD player.The light stops blinking too. So don't worry about it , it's fine.
AnswerI believe that is an anti-theft device, there is a thin peice of plastic that when you push a button it pops off and when that happens, you can't turn on the CD player.The light stops blinking too. So don't worry about it , it's fine.Can't get 2002 ford focus air filter box to open screws just spin how can I get it open?
I had the same problem with my 2002 SE. There are retaining nuts underneath that are rusted to and spinning with the screws. Your going to have to use a small pair of vice grip pliers to hold the nuts still while loosening the screw. Its possible to do this without removing the air filter box, but is probably a little easier with the filter box out (I did mine without removing, the top left nut was a little difficult to get to). I would suggest you use a ratchet for this opposed to a screwdriver. Once loose, spray a little wd-40 on the bolts and nuts to make it a little easier for next time.
What are the torque specs on the main and rod bearings on a 2004 Ford focus 2.3?
Guy at the ford dealer shop supervisor told me 35 NM, then additional 90 degrees but dosent that seem like a lot
How do you replace the oil seals on a 1993 Ford Taurus Station Wagon with 3.0 engine?
Get a manual on your car from DISCOUNTAUTOREPAIRMANUALS.COM. there are many seals and some have to be done with the engine out.
When do you use the overdrive function?
All the time. I assume you are talking about an automatic transmission. In that case set it in it's highest position (overdrive) for all normal driving. This will give you the best gas mileage. Wrong. When you use the overdrive, he means when you take the overdrive off. It's used when you go down steep hills to slow the speed down. Or when you need extra power to overtake (pass) another car Both are correct. During the course of normal driving the car should be driven with O/D On. This will provide the best economy as well as improve ride comfort (engine isn't working as hard and is quieter). But when descending a hill it can be turned off to help control vehicle speed without using the brakes, or to assist the brakes in slowing the vehicle. This works much like 'down shifting' in a manual transmission vehicle. Also in most vehicles O/D should be turned off when towing or hauling large loads to keep the transmission from getting overworked. If a vehicle is working properly it will disengage O/D by itself when you use 'full throttle', such as when passing someone. There is no need to disengage it in this circumstance.
What size tool is needed to take off the front calipers on a 2000 ford expedition?
Replacing Disc Brake Pads *** Caution *** Older brake pads or shoes may contain asbestos, which has been determined to be cancer causing agent. Never clean the brake surfaces with compressed air! Avoid inhaling any dust from any brake surface! When cleaning brake surfaces, use a commercially available brake cleaner fluid. Print 1. To avoid overflowing of the master cylinder when the caliper pistons are pressed into the caliper cylinder bores, siphon or dip some brake fluid out of the large reservoir. 2. Raise and support the vehicle on jack stands. 3. Remove the wheels. 4. Place a suitable C-clamp on the caliper and, with the clamp bearing on the outer pad, tighten the clamp to bottom the caliper pistons in the cylinder bores. Remove the C-clamp. 5. Loosen and remove the caliper retaining bolts. Torx T-40 or T-45 6. Lift the caliper off the rotor. è Do not allow the caliper to hand by the brake hose. 7. Remove the brake pads and anti-rattle spring. To install: 8. Thoroughly clean the areas of the caliper and spindle assembly which contacts each other during the sliding action of the caliper. 9. Place a new anti-rattle clip on the lower end of the inboard shoe. Make sure that the tabs on the clip are positioned correctly and the loop-type spring is away from the rotor. 10. Place the lower end of the inner brake pad in the spindle assembly pad abutment, against the anti-rattle clip, and slide the upper end of the pad into position. Be sure that the clip is still in position. 11. Check and make sure that the caliper piston is fully bottomed in the cylinder bore. Use a large C-clamp to bottom the piston, if necessary. 12. Position the outer brake pad on the caliper, and press the pad tabs into place with your fingers. If the pad cannot be pressed into place by hand, use a C-clamp. Be careful not to damage the lining with the clamp. Bend the tabs to prevent rattling. 13. Position the caliper on the spindle assembly. Lightly lubricate the caliper sliding pins with suitable grease. 14. Position the caliper pins into the caliper anchor plate. 15. Tighten the caliper pins to 16-30 ft.lbs. [22-40Nm] on 1997-98 F-250HD, F350 and F-Super Duty models. Tighten the caliper pins to 21-26 ft.lbs. [28-36 Nm] on the F-150, F-250, Expedition and Navigator. Tighten the caliper pins to 42 ft.lbs. [56 Nm] on the 1999-00 F-250SD, F-350 and F-Super Duty models. 16. Install the wheels. 17. Lower the vehicle. Pump the brake pedal a few times to build adequate pressure in the brake system and check the fluid level in the master cylinder.
No heat or ac in my 2001 Ford Focus?
You probably have malfunctioning blower fans. A blown fuse can cause your blower fans to malfunction. The heat and air conditioning cooling is not being forced into the passenger cabin.
How many horsepower does the engine in the 2007 Ford Focus have?
The 2007 Ford Focus's engine produces 136 hp @ 6000 rpm.
How much does a passenger window on a 2 door Ford Focus costs?
Have a look on eBay then take a tenner off at your local scrapyard
Between 25 and 40 psi (Put it more likely at 35psi)
How do you change the oil on a 2000 Ford Focus?
follow the instructions here http://myfordfocus.com/how-to/oilchange.htm
Where can you find a fuse box diagram for 1996 2010 Ford Focus?
In the repair manual. NAPA, AutoZone.
How do you change the blower motor switch on a 2001 Ford Focus?
If you are talking about the fan speed switch on the dash panel you need to pull the whole front panel loose..carefull not to break or damage plastic snap in tabs...the radio face plate needs to be loosened also it to has plastic tabs cause i broke mine not realizing it had them..then the switch just unplugs take off backing nut and install new one
Where is the cigarette lighter fuse on a 2006 Ford Focus?
its in the fuse box that is located on the left of your steering wheel, behind the CD holder, most likely you will have to remove the holder to get a clear reach.
Spark plug gap for 2002 ford focus 2.0?
Look on the sticker under the hood. Some of the same models might be different. Someone said advised not to gap plugs, install them right out of box. Not true, do u think these plugs from another country are going to be perfect after such a trip? I installed 4 plugs out of the box, one was not correct. Had to take it out and re-gap bcuz it mis- fired. It was perfect after that. U did not mention what brand of spark plug that u gaped and installed in ur vehicle. Some say DO NOT gap bosch plugs, and say to get the ford brand. You are advised NOT to gap single plat plugs, u are safer with double plat plugs. Use a wire spark plug gaper not a solid one. Most of these double plat plugs come with a 5 year warranty. Check it out. Also, why did you have to pay $150.00 to have ur car fixed. If u changed ur own plugs, did u not think that it possibly something that u had recently done?
