0
Ford Ranger XL
The Ranger XL is a pick-up truck manufactured by the American automaker Ford Motor Company. Some of the notable features found in the 2010 model are Electronic Stability Control, and torso and head airbags in the front seat.
4,911 Questions
How do you fix a GTO idling problem?
Others claim to have experienced idling problems with their GTO's aswell before their its' engine computer learned the new flow of the LS1Speed intake. Initially, the car had a bit of a hesitation to startup when the key was turned, but that issue went away as the computer learned. Probably the most noticeable effect the system had was that it made the intake snarl much more audible, which is always a plus.
The simple answer to this question is that a V6 is an engine that has six cylinders, there are two types, Inline 6 and V6. Inline 6 means that there are 6 cylinders in a row and a V6 means that the cylinders are in a V formation 3 on each side of the block. On the Ford Bronco II or the early Ford Rangers you would have what is refered to as a "Cologne" 2.9L V6. this is a 60° cast iron block V6 engine built by the Ford Motor Company in Cologne, Germany (thats where it gets its name from). The output was rated at 140 horsepower @4600 rpm for the Light trucks (1986-92 Ranger & 1986-90 Bronco II)
What causes a 87 Nissan truck not to turn over?
check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay.
How do you take out the headlight assembly to change the bulb on a 99 grandam se?
No need to remove the headlight assembly. twist & remove the light bulb from the rear of the headlight assembly. Do not touch the new bulb glass with your hands. Oils from your hands will cause bulb failure.
How do you add transmission fluid to a 1991 Ford Ranger with a 5 speed manual shift?
Do this with the truck level. Crawl under truck (if you can). Find large hex-head bolt on drivers side (in the side) near middle of transmission. This is the fill plug and looks like a large bolt. Unscrew the bolt. Fill (with Mercon ATF most likely) Use a large squirt-squeeze bottle like Lucas Injector cleaner (large size), and fill till fluid BEGINS TO RUN OUT. If fluid runs out when you take the plug out, then you don't need to add any.
What are the torque specs for a CR125R?
it all depends on the size of fastner go online and print out atorque spec sheet for metpic fastners
What if you hear only a click when you try to start a 1991 Cadillac DeVille?
It may be possible that the wire connections on the starter or battery are broken or corroded. It could be your starter relay. Or your starter should be tested to see if it needs replaced.
How do you remove the horn pad in the center of the steering wheel from a 1988 Dodge Ram 50 truck?
I'm no expert at fixing cars, but I just pried the rubber part off. It's a cover (or sleeve) that wraps around a plastic thing that creates that weird rhombus shape. Just keep pulling at it and it will come off. My horn is ON constantly and I can't figure out why. That's what made me try to take it apart in the first place. I was able to get the horn pad off, and the brass noise-maker part and even see some wires and connections. But I have yet to control the horn. So I just removed the fuse and don't drive it alot. Anyway, hope that helps! Let me know if you have any (inexpensive) solutions for me.
Is the recommended timing setting of 1-2 deg btdc correct on a Ford Festiva?
YES IT IS + OR - 1 TO 2 DEGREES BEFORE TDC...
How many watts does an immersion heater use?
The wattage of an immersion heater typically ranges from 1,000 to 3,000 watts, depending on the model and its intended use. Common household immersion heaters usually operate at around 2,000 to 3,000 watts for efficient heating. The specific wattage will be indicated on the heater itself or in its specifications. Always check the manufacturer's guidelines for precise information.
How do you remove the spare tire from a 1997 ford ranger?
use a socket to loosen the bolt holding it up and pull the bracket down
Where is the dpfe located on a 1999 ranger 4.0?
I believe it is on the drivers side of the engine , on the side of the upper intake
manifold
What weight oil does a Ford Ranger use?
That would depend on what year of Ford Ranger and what size of engine it
has
Ford 4.9 where is your number 1 cylinder?
The # 1 cylinder for the 4.9 L ( 300 cubic inch ) straight 6 cylinder Ford is the cylinder at the front of the vehicle
What's the Spindle nut torque for 2wd 2000 ford ranger?
while turning rotor ccw, tighten nut to 17 ft/lbs.
loosen nut and while turning rotor cw do a final tighten of 17 in/lbs
Could be a vacuum leak in or at the power brake booster
Will a 2008 Ford Ranger bed fit on a 2003 Ford Ranger?
yea. the bolts might not line up, but that's only 6 holes you have to drill out
Where is the starter on 1994 ranger?
on the driver side underneath, it right by you tire and it hook up to your tranny
I would check the bulbs in the tail lights first. Your Brake switch is working ,because of the third brake light is coming on.Ususally all the brake lights are on the same fuse.... Thanks Dom
AnswerCenter window light is on a separate circuit. Manufacturers did that so you don't lose all the brake lights at once. Check connections at brake switch and fuses. If ok look for broken wire in harness...............good luck, MikeHow do you change the u joints on a 1988 ford ranger?
hey this is pretty easy to do first block the wheels, jack the truck up then drop the drive shaft out remove c-clips from the ujoints then take a socket or piece of pipe that fits in the hole and hammer the old one out after they are out clean up the ujoint holders and install the new ones carefull of the pin bearing inside them put driveshaft back in ready to go hope this helps a little
In my opinion it is Compound 1080 "This poison is odorless, tasteless, and has no antidote. The bodies of those killed with 1080 remain poisonous for a year."
Where is the battery located on a 1997 Plymouth Breeze?
Drivers side fender well. Jack up the car and remove the front tire. There's a section of the fender liner with a big picture of a battery on it. You can remove that part of the fender liner via some thumb twist screws and get to the battery
If the capacity is 6.5 quarts of engine coolant what is the refill ratio of water and new coolant?
You need a 50/50 mixture of water and antifreeze.
