0
Ford Windstar GL
The Windstar GL was a first generation Windstar model which was produced by Ford Motor Company. Some of the standard features of this car are dual airbags and anti-lock brakes.
1,070 Questions
How do you replace lower ball joints on a Isuzu rodeo?
I would like to find the answer to this question as well. I am in the middle of doing just that and I am finding it to be a very involved project because the axle gets in the way of the ball joint removal once you have it all loose and ready to remove.
Where is the speed sensor located on a 2002 Kia Rio?
top of tranny below throttle body one plug in and a 10mm bolt holding it down
Were is the fuse box for ford windstar 04?
On the ( 2003 ) Ford Windstar which was the last model year , the fuse box is
below and to the left of the steering wheel , by the brake pedal ( it has a cover
on it ) and the Power Distribution Box ( which is " live " ) is located in the engine
compartment between the battery and the drivers side front fender
How do you reset the stereo system when it reads 'off' in a 1999 Volvo S70?
must have code in owners manual
Turn the ignition to position one (accessory), turn on the radio so you can see the display, and come back in 2 hours. The display should read "CODE". At this point you must enter the code for your radio. I have owned 4 VOlVOs (1998 through 2006) and have never found the radio code in any of my manuals; perhaps it was published for earlier models.
If you do not have the code, remove the radio by pushing on the vertical buttons on the radio face. They pop out and provide a means to slide the radio forward. Copy down the radio model, eg. 813, 816, and serial number. Bring this information AND A COPY OF YOUR REGISTRATION SHOWING THE VIN to your dealer, or to any Volvo dealer. They need to correlate the VIN and radio SN to be assured that the radio had not been stolen. They can look up the the code in a database and provide it to you. If they tell you the radio is no good or want to charge you a ridiculous fee, go elsewhere.
Once you have the code, turn on the radio and enter is using the preset buttons. Wait a moment, and the radio should turn on. If it does not, the code is incorrect. This is possible if the radio you have is not the one that was shipped with the original vehicle. If so, you must remove the radio and bring it to the dealer who can reprogram a new code into the radio. Depending on the circumstances, they may or may not do it for you, because they have no proof that you are the legitimate owner of the radio.
If not, I saw an advert for radiocodes.com who claim they just need the radio SN and will provide the code for a fee.
How do you fix the reclining lever on a 1999 Monte Carlo drivers seat?
Sorry I can't help, but I have the same question on a 2001 Monte ........ my seat reclines past the first stop. Thanks
Why does your 1998 Mercury Mountaineer AC cycle off and on when running?
Usually when the A/C cycles it means it's low on freon.
Where is the cord for the blockheater on the 1995 ford windstar?
If you are under the front of vehicle,its on the bottom front of engine facing the radiator.
Front tires need balancing , if it still does it, tires need replacing. Avoid going beyond the speed limit, and the problem should resolve itself.
Trouble code P1408 means: Exhaust Gas Recirculation Flow Out Of Self Test Range
Where are the sensors located on a 1995 Windstar GL?
there are alot of sensors which one are you looking for
Where is the speed sensor located for a 1989 integra?
The speed sensor on a 1989 Acura Integra is located on the transmission. It is a small unit with a two-wire clip which connects to the main engine harness of the vehicle.
What does the rear abs light mean on your aerostar van?
The rear ABS light on your Aerostar van indicates a potential issue with the anti-lock braking system (ABS) in the rear brakes. This could be due to a malfunctioning ABS sensor, a problem with the ABS module, or low brake fluid levels. It's important to have the system checked by a professional to ensure safe braking performance and address any underlying issues. Ignoring the light could lead to reduced braking effectiveness.
Why does a 1998 windstar cuts off when coming to a stop and theres no code?
A 1998 Windstar cutting off when coming to a stop without generating a code can be due to several issues. Common causes include a failing idle air control valve, a dirty throttle body, or fuel delivery problems, such as a clogged fuel filter or weak fuel pump. Additionally, vacuum leaks in hoses or issues with the mass airflow sensor can also lead to stalling. It's advisable to perform a thorough inspection of these components to identify the root cause.
How do you replace bulb in instrument panelona 97 ford windstar van?
To replace the bulb in the instrument panel of a 1997 Ford Windstar, first, disconnect the negative battery cable to ensure safety. Remove the dashboard cover by unscrewing the necessary screws, then gently pull out the instrument panel. Locate the burnt-out bulb, twist it counterclockwise to remove it, and replace it with a new bulb. Finally, reassemble the panel and reconnect the battery.
What is causing your 1996 ford explore to idle up and down also want to stall?
The erratic idle and stalling in your 1996 Ford Explorer could be caused by several issues, such as a dirty or malfunctioning idle air control valve (IAC), a vacuum leak, or a problem with the mass airflow sensor (MAF). Additionally, issues with spark plugs, ignition coils, or fuel delivery problems, like a clogged fuel filter or failing fuel pump, could also contribute to these symptoms. It’s advisable to perform a diagnostic check to pinpoint the exact cause.
What does the codeB1600 mean on Ford Windstar?
The code B1600 on a Ford Windstar indicates a problem with the Body Control Module (BCM), specifically related to the vehicle's battery voltage supply. It typically points to issues such as a weak battery, poor connections, or a malfunctioning BCM itself. Diagnosing the exact cause requires checking the battery and electrical connections, as well as testing the BCM for faults. If unresolved, this code can impact various electrical functions in the vehicle.
What is intake manifold runner control?
Intake manifold runner control (IMRC) is a system used in internal combustion engines to optimize airflow into the engine's intake manifold. It adjusts the length and cross-sectional area of the intake runners, typically through the use of valves or flaps, to enhance engine performance across different RPM ranges. By altering the airflow characteristics, IMRC improves fuel atomization, increases torque, and enhances overall efficiency, especially during varying driving conditions. This technology helps achieve a balance between low-end power and high-end performance.
How do you remove rear side panels on 2001 Windstar?
To remove the rear side panels on a 2001 Ford Windstar, start by removing any screws or clips securing the panel, which are often located in the armrest area or at the bottom edge. Gently pry off the panel using a trim removal tool to avoid damaging the clips. Disconnect any electrical connectors if applicable, then lift the panel away from the vehicle. Be mindful of any hidden fasteners to ensure a smooth removal process.
