GMC Sierra

350hp thats why they call it a 350 5.7

Th above answer is ridiculously wrong. The 5.7 V8 is called a 350 because the engine is 350 cubic inches in size not because it has 350 H.P. I would have to know the year GMC Sierra in order to be able to tell you the H.P. It ranges from 145 H.P. to 370 H.P.

8x6.50

Replacing the brake light switch is a difficult process due to working in a very confined space. Before attempting to replace the switch, check the fuse in the fuse box on the end of the dashboard then the fuse and the relay in the relay box under the hood. If all these are good, then the problem is probably related to the switch.

The brake light switch is located above the steering column. There is a circular retainer that holds it to the shaft. There is a split in the retainer that must be opened in order to remove the retainer. Use a long, thin screwdriver to spread one side then the other. This will bend the retainer enough that it will pop off. Rotate the switch to disengage it from the rod and slide it off the shaft. Use a screwdriver to depress the electrical connector lock and unplug the connector. Replacing the switch is the opposite of the removal operation.

Well....Seeing how this happened to me a month ago I'll give you a heads up. Worst case you could've bent a connecting rod (Hydraulic Lock-Up), or maybe sucked enough water (mists of water) through the air intake to thin out the oil to a point where you spun a bearing, or you even could've bent a valve. BUT... Driving through puddles isn't a big deal. Calling roadside assistants from the middle of a river is.

according to my manual 3flashes,pause,3 flashes deals with the map sensor........check the vacuum hoses from map sensor.check the electrical connections to the ECM. Replace the map sensor. Hope it helps good luck!

Jack up front of vehicle, and secure on jack stands. place a drain pan underneath the engine oil pan drain and remove the bolt. While this is draining take your new filter and with your finger rub some new oil all around the rubber seal. Wait until the engine oil is drained and put the bolt back into the oil pan, move the drain pan underneath the oil filter and loosen off the filter and dump oil into drain pan. Put the new filter on carefully, if it doesn't turn freely it's not on straight, tighten the filter with your hands, once the filter is lightly snug, turn another 3/4 turn. Take away the drain pan and drop the vehicle back down. Clean the area on and around the oil fill cap located on the valve cover. Remove the cap and fill the engine with the appropriate amount of oil for you size engine. Put the cap back on and run the vehicle for 5 minutes checking for leaks under vehicle. Turn off engine and let cool for 10 minutes, check oil and fill to appropriate level.

Next time you drive anywhere, when you return wait 10 mins and check oil again.

It's always best to get torque specs and bolt sequences from the machine shop that performed the work.

Since you're discussing head torque specs, I assume the head has been removed. Since the head was removed it should have been checked and if necessary, milled flat by a machine shop (minimum requirements for a removed head).

Your machine shop should be willing to give that information to you when you pick up the heads.

The only way to measure your creative ability is to develop it by exploration. There is no way of knowing how far it can span. Test yourself by going shopping for supplies. What can you put together? If on a budget, how inexpensive can you create something that will be unbelievable? What can you make out of old cans, car parts, kitchen utensils, etc.? How many genres of art can you cross over into? Could you amuse or entertain yourself with absolutely nothing other than your imagination? Can you make up poems or songs off the top of your head? Can you meet unexpected deadlines? Are you spontaneous? Are you open minded with a bendable brain? Discovering the depth of your creative abilty means being willing to study your own perceptions on everything. Creativity and skill come together to work as one if you throughly study the dynamics of art while leaving more than enough room for playful creatvity. And of course skill can develop itself through constant creativity. Here are more opinions and answers from other FAQ Farmers: * An IQ test..? * With reference to the above answer, I don't think an IQ test will reveal anything about creativity. In general, I associate IQ tests with analytical abilities, which is something very different. I agree that one has to explore and experiment. I'd attach less importance to being spontaneous, as there are some kinds of elaborated and highly time-consuming forms of creativity. As for the financial dimension, one must (usually) be prepared to spend some money on one's explorations, but it needn't be that much initially. For example, if you think you have potential as a photographer, you will need to buy a good camera. (This needn't be expensive; you can get an excellent secondhand camera on ebay, for example). There are tests that try to measure creativity... although I completely agree that it is best to do some exploring. But if you really want a formal test, here is a site that might lead you to a good test, depending on what kind of creativity you are trying to measure. :) http://www.indiana.edu/~bobweb/Handout/cretv_6.html

You have either a blown head gasket or a cracked head. Serious engine dame will occur if this is not repaired. Do not drive the vehicle in until it is repaired. Probably head gasket, intake gasket, cracked head, cracked block, If there is no compression getting into the radiator, you may be able to put one of several stop leak products in the cooling system that may fix it. All of these types have a clear liquid with a copper colored part in the bottom of the bottle. May fix it, may not, but it's only about $8. I have had good luck on head gaskets leaking into the exaust.

most likely a lower manifold gasket -- gm and aftermarket both have change up gaskets, believe it or not but gm is cheaper \

It is located on the firewall on the passenger side of the vehicle. It is directly below thae passengerside windshield wiper. Look for a plasctic cover with writing on the top such as "Power block" or "Fuel pump relay" or "Fuel pump Fuse"

might want to check your drums

Fault code P0174 in Chevrolet SUV/Trucks indicates the engines fuel/air mixture is too lean. The most probable cause for this is usually a defective or malfunctioning engine exhaust oxygen sensor.

what fluid lots of them

It could have, All you need to do is call a GM. dealership and ask for parts.

Then ask the parts man if he can tell you what the gear ratio is in your truck.

He will ask you for the VIN# so you need to have it wrote down so you can give it to him. Ask him what the gear ratio is and if it's positive trac.

Dead batteries.

hi, usually (even though this is a safety feature :) if you reach under the back of the drivers seat, right near the pieace that you put your seat belt into there is a wire there comming out of that buckle. There will be a little wiring harness (only two wires I think) disconnect this harness and your set! But this harness is a real pain to get to. Use a flashlight to help and small hands couldn't hurt either.

yes, yes it does

no, its the crappy tbi systems.

tbi stands for THROTTLE BODY INJECTION! it has fuel injectors and has to be treated as such. it is not carbureted.

here comes the bubble buster,,, YOU DONT

Ping is caused by the timing being too far advanced either becasue it is set to far advanced or the advance system is malfunctioning. Prior to 1996 you can adjust the timing manually but after '96 the computer does it all.

how do u change a crankshaft sensor on a Oldsmoilbe alero 2001 2.4L twin cam?

Passenger side, exhaust system. Start at the exhaust manifold and go backward toward the converter. You will find the O2 sensor.

Need to replace ignition coil "D" for my 2000 GMC Sierra 5.3. Need to know which coil is coil D.

Thank you,

Adam

It's all about the combination, so it's impossible to answer the question. However, it's reasonable to say that the overbore should produce at least 2 or 3 horsepower, the headers could add 10 horsepower, the intake, 5-10 horsepower, and the heads could add anywhere from 10-100 horsepower.

Your 2000 4.8 liter Sierra might run rough at an idle because of clogged fuel injectors or a clogged fuel filter. You might also have gotten water in the gasoline.