0
Honda Accord EX
Introduced in 1984 with a 1.8 liter engine, Honda Accord EX was marketed in New Zealand, Australia, Canada, and the US. The EX replaced the LX-I and SE-I models during the 1990s.
5,157 Questions
How can you tell if the starter is bad on a Honda accord 1999 ex v6?
Does it it start sometime and not others? Does it click when you turn the ignition to start but doesnt start? Then its probably bad. Make sure your battery is fully charged first.
2003 Honda Accord left turn signal not working?
well i had Honda accord 2003 coincidently too, and i had the same problem as u r having, but my right turn indicator wasn't working, i asked the mechanic for the reason and to repair it, it was simple burned wire, so i would suggest u to get it checked with the mechanic, it's not a big deal.
How do you remove a factory car stereo from a 1994 Honda Accord EXi?
Take out the ash tray and unscrew the screw back there that holds the kit in place.
How do you remove fuel pump 1997 camaro v6 3800?
Buy a haynes manual which will explain everything to you. You can pick one up for about 20 bucks at a local auto parts store.
What does the brake lamp light indicate on a 1986 Honda accord?
Low brake fluid level or Parking brake not released completely
How do you remove governor from 1996 Honda accord?
There is no governor to remove. Speed is controlled by the ECU (computer).
What does the VSS do in a 91 Honda Accord?
The VSS (Vehicle Speed Sensor) moniters the speed of the vehicle.
How do you remove the rear deck 6x9 speakers in a 1991 Honda Accord Ex Sedan?
look at them from in the trunk. there should b 3 bolts around them. take those off and and disconnect wires. lift assembly up and out from inside. undo all screws on the whole piece you pull up and u will free the speakers. but u might need bold cutters because i put aftermarket 6x9s in mine n there is a bar 4 the trunk stickin out a lil 2 far so my speakers wont sit flat till i get bolt cutters cuz they have a bigger magnet than the stock speakers.
How d you find the code for AA 2007 Honda accord?
Call the dealer you bought the car from and they will give you you car's 5-digit code number.
What are the stereo wire color code for a 92 civic?
Constant 12V+ White/Blue Switched 12V+ Yellow/Red Ground Black Illumination Red/Black Dimmer n/a Antenna Driver's Pillar Front Speakers 6 1/2" Doors Left Front (+) Blue/Green Left Front (-) Gray/Black Right Front (+) Red/Green Right Front (-) Brown/Black Rear Speakers 5 1/4" Rear Deck Left Rear (+) Blue/Yellow Left Rear (-) Gray/White Right Rear (+) Red/Yellow Right Rear (-) Brown/White
How do you know the wheel barring are bad?
A grinding or abnormal noise at the wheel is a good sign the bearing is bad. Unload the bearing by moving the vehicle left or right while moving. If the noise comes and goes when doing this, the bearing is bad. The only positive way to verify this is to remove the bearing and look at it. Pitting, scouring, and any other signs of wear indicate the bearing needs replacing. Be sure and replace the race if it is not perfect.
How much does a master cylinder cost for a 1994 Honda accord?
I just had to replace mine this week. I got mine at O'Reilly's for $25.
No, they are not interchangable.
Where is the location of OBD of 2003 Honda Accord?
The 2003 Honda Accord OBD 2 port is under driver side dash above dead pedal
How do you change the front turn signal light in a 1999 Honda Accord?
1) Turn the wheels in the opposite direction of the dead signal lamp (e.g. if left turn signal is out, turn wheel to the right).
2) Using a screwdriver, pop the forward most snap holding the wheel well liner in place. To do this, gently pry up the inner piece of the snap from both sides. If they break, you can buy replacement snaps at any Honda dealership. I keep a few on hand.
3) Peel back the liner so there's enough room to get your hand in. Feel around until you find the wires, then follow them to the lamp socket.
4) Turn the entire socket counter clockwise 1/8th of a turn and it will pop out. Pull the entire socket GENTLY out the wheel well.
5) Install the new bulb wearing surgical gloves or holding the bulb with a tissue, as getting any oils from your skin on the bulb shortens the bulb life. The bulb fits into the grooves in one specific way.
6) Reverse these steps to reinstall.
Honda recommends it -- But I would not have it done for at least double ot even triple the mileage they recommend.
How do you put in a 2004 dodge ram 2500 water pump?
Will the rad need to be removed to make room?,or is it as easy as it looks by removing a couple bolts ? Will the rad need to be removed to make room?,or is it as easy as it looks by removing a couple bolts ? Will the rad need to be removed to make room?,or is it as easy as it looks by removing a couple bolts ?
What does code P1167 mean for a 1998 Honda Accord?
o2 sensor My list shows P1167 Invalid Test,throttle not depressed
2002 Accord transmission oil replacement?
Use only Honda brand ATF-Z1 transmission fluid. There is no substitute, no matter what anyone tells you. Use another fluid and you will experience shifting problems. I would find a Honda dealer with a Wynns trans flush machine and have the trans flushed. This is the only way to remove all the fluid. Change the fluid every 50,000 miles.
Where is fuelpump on 1992 Honda Accord?
Inside of the gas tank. The only way to get to it is by removing the tank from the car.
You will find that inside the trunk underneath the carpet there will be a cap you can remove, this is not the fuel pump, I promise you. It is the float for the gas meter. I don't recommend removing this, I did and it resulted in a strong smell of gas every time I fill up.
Can you change the timing belt and water pump yourself on a 2003 Honda odyssey?
Not unless you know what you are doing. This is an interference engine. Do this incorrectly, start the engine, and you will have internal engine damage.
It shortens the life of your transmission by shifting in and out of gear to get the longest life you would leave it in drive at all times every time you shift in and out of gear you are putting pressure on the plates when going back in gear causing wear and tear also make shure you are completely stopped when going from forward to reverse for the best tranny life
I disagree. Long periods of idling while in gear & holding the brake, such as stop lights, trains etc. generates a LOT of excess heat, which is a Trannys worst enemy. Shifting into Neutral then back into gear is not all that hard on Trannys.
I don't believe the Engine is affected in either case.
