0
Mazda MX-3
The MX-3 was a 4-seat hatchback manufactured by Mazda Motor Corporation from September 1991-1998. This 3-door vehicle was known for its capability to use a wide range of engines such as the KL-ZE and V6.
407 Questions
heater core leaking
Where is the fuel pump on a 94 Mazda mx3 located?
look underneath the rear seat, the access panel is right there, just undo the four screws, lift the plate and then remove the little screws around the top of your fuel pump. It should pull out easily
How do you remove the dash board or instrument panel on a '95 Ram pickup?
To remove the insrument panel you have to first remove the four screws in the black plastic trim surrounding your dash one in each side of the cup holder and one in each side of the ash tray. Then put the truck in first gear and pull on the plastic piece it will come out you have to unplug the cigar lighter and the power outlet before it will come all the way off. There are screws holding the panel in, remove them but don't start pulling on the panel just yet first you have to remove the knee panel located below the steering wheel there are screws for the towards the bottom of the panel. You need to look on the steering column for the shifter indicator wire. Its a small wire with a flat piece of metal on the end of it with a rectangular hole in it. You need to remove that from the column. It is snaped into a white plastic piece and you need to pop it out of that also. Now you can pull the panel out partialy and it will have two sets of wires going to it one on the right and one on the left unhook them both and your home free with that.
For the dash you will need to do all of the above formentioned things as well as remove the five bolts in the dash up by the windshield. You also need to remove both the right and the left kick panels located by the floor under the dash they also go down beside the seats. Remove them and there are two bolts you will see them they are surrounded by the pivot hinges for the dash. Remove the five top bolts by the windshield loosen these two bolts and the two steering column bolts and the dash will roll on its hinges and start to lay down towards the seats. Then all that's left is the wiring harness and heater controls. Before letting the dash roll remove the heater controls and unhook the wires and vaccum lines going to the back of them, I hope that I was of some help to you. Good luck
Where is the inertia switch on a 1993 Mazda MX3 4 cylinder?
The 1993 Mazda the inertia?æswitch can be found on the firewall in the engine compartment. The inertia switch will be on the passenger side of the firewall.
Why does my 1995 Mazda MPV heater cuts on and off?
Check your coolent level! Yours is low and the on/off heat gives you a warning that your going to run out of coolent and trash your engine.
with the radio s/n number you will have to get the reset code through a Honda dealer with the radio s/n number you will have to get the reset code through a Honda dealer
How do you replace an alternator on a Mazda 323f p reg is this a easy job?
The alternator is below pipework and fittings and will take a long time to remove - according to my mechanic. Going to do it myself even though it will take me even longer!
Why would the driver's side automatic seatbelt in a Mazda MX3 beep almost constantly?
I own a 1993 Mazda 323. I had the same problem with the automatic seatbelts. I found out that the problem is caused by a little round circuit. This circuit is in the middle consol where the seatbelts are stored (I believe it is attached behind the pulley of the seatbelt housing. It looks like Mazda is using some kind of conductive metal which is worn out by time. Since the metal on the circuit is worn, seatbelt safety circuit stays open and causes seatbelt alarm stay on. I just changed the driver's side with the passenger's side and beep went off. However, I would recommend you to contact the Mazda dealar and ask if you can have this part replaced.
or Timing is off. This is known as dieseling. The car runs off combustion and burned gases still in the cylinder even if the ignition is off. Make sure marks are lined up on the camshafts and crankshaft. mostly likely have to remove the valve cover to check timing. Even though its a chain timing can still skip a mark. Another thing to do is make sure the piston is on top dead center and the dist. is firing on the number 1 cylinder.also try Removing the spark plug on number 1 and have someone turn it over as you watch for a spark.
How fast does a 500cc speedway bike go?
it would all depend on what gearing ratios were used , there is a difference between long track bikes and short track bikes ,on average they can reach speeds of around 70 miles per hour .
It could be that the clutch pressure plate isn't doing its job or maybe the linkage has been damaged in some way? when you press the clutch in if you can go from one gear to the next through the gear box and let off the clutch and it just idles i would replace the entire clutch system you can get one pretty cheap from:
http://www.clutchcityonline.com/products/10-043.shtml
Have fun and keep the rubber burning Mazda for life!
Mazda mx3 Driving Lights and cluster lights dont work why?
The multifunction switch that allows you to turn you headlights is broken. The only way to find out is to replace it or take it to a mechanic.
Where is the IAC Valve on a 1993 Mazda MX3?
The idle air control valve is on the the bottom of the throttle body.
Mazda mx3 gets no fire changed fuel pump distributor pcm timing belt crank sensor what is left?
try HEI mod it should work http://www.mx-3.com/phpBB3/viewtopic.php?f=15&p=461052
What is the firing order for 1992 Mazda 121 1.3L 16valve automatic?
I cannot find a photo on a 1992 Mazda 121 or the 1.3 engine. However I would suspect the firing order & connections would be the same as the 1.8L engine. I will post a link showing the connections on the 1992 1.8 L engine. Try this connection.
Which engine can get higher mileage- rotary or piston?
Piston for sure gets better milage unless you have a V8 or higher. Rotary drinks its gas.
in mint condition about 3000, but mine is a 95 in great mecanical condition, and is only worth 1000 dollars (on nov 12 2008).
Do an internet on a Mazda RX7 or RX8... other than that ....it's basically an airplane engine..... ---------------------------------------------------------------------------------------------------------------
A rotary engine, or formly known as the "wankel" engine was created/invented by Felix Wankel back in the 1920s i believe, prototype was designed an released in 1959.
Mazda well know for the RX(Rotary Experiment) Gen cars 1-8.
There are a few kinds of rotary engines, the ones in airplanes, and the ones used in cars/trucks.
The basic rotary engine from a car IE Rx7. has a 13b rotary engine, which is a 2 rotor model.
The rotary engine , instead of a traditional piston engine does not go up an down, instead goes in circular motion (which allows it to get way more RPMs). there are plenty of rotary engines 12a,13b,20b, and 26b(which is hard to come close too...AND ALOT OF $$$$$)
thats basically a lil about the rotary engine!!!
Alignments of Camshaft timing marks for 92 Mazda MX3?
4 cylinder or v6?
Check the online manuals thanks to MX-3.com
http://www.mx-3.com/manuals/index.php?folder=/1992%20Workshop%20Manual/
What causes a rough idle on Mazda mx3?
I had this problem when I bought my mx3, found the cause to be a sticking EGR valve, I applied vacuum with a vacuum test tool and that was enough to unstick the valve and has been fine ever since.
