0
Oldsmobile Cutlass Supreme
Manufactured by General Motors from 1966 to 1997, the Oldsmobile Cutlass Supreme was a mid-size car produced in five generations. Its fifth generation model was available in three body styles: 2-door convertible, 2-door coupe and 4-door sedan.
2,211 Questions
A siphon is a tube that is used to take a liquid up and out of one container and into another container or the ground. A hose used to empty a swimming pool can be called a siphon.
What is the firing order for a 1986 Oldmobile Cutlass Ciera 2.8 V6 if it is not 1-2-3-4-5-6?
The firing order for a 1986 Oldsmobile Cutlass Ciera 2.8 V6 is 1, 2, 3, 4, 5, 6. The number one cylinder is on the front left as you face the engine compartment.
Why is your speedometer moving up and down even while stoped at a red light?
If your aren't on the RPM mode it's a sensor or computer problem
Where is the crankshaft sensor located on a 1993 Chevy Lumina Z34?
You'll need to pull the passenger front wheel, remove the wheel well cover. This will expose the damper pulley on the crankshaft. Remove damper pulley, remove plastic engine cover. Look inside you will see the sensor. Be sure if you replace it to install the new one exactly the same as the old one was.
Generally the turn signal flasher is located on or near the steering column. I hope this helps you. Mark
AnswerThe turn signal switch is locate on the steering column on the Left side as a lever that your move up and down. The same lever has a tab switch pending make for cruise control and a turn dial for windshield wipers. The Right lever is the gear shift.If the hazard light it's a black nub button on right of the steering column - near the gearshift that requires a push internal a twist & pull up on the outer ring to cut on to cut on is more difficult then cut off only issue. It's is difficult to set and difficult to release - again it is as described figuring out if you push and pull the outer ring around the button at the same time with either a a twisting action clockwise or counter clockwise.
The referral toward the glove box is where when you open it there is a panel to the left for the relay switches and fuses if it's not working it's a matter of unplugging and replacing with a new one. Usually, if not a cycle of needing the light bulb replaced the glove box relays the location if you possible location to replace fuses or unplug fuse box if servicing the battery of the car....
"Note replacing the battery without unplugging the main fuse box may result in shortages of lesser fuses or other electrical wiring damage as most common is the power window switches if the fuse relay box is not disengaged before replacing or servicing batteries in this model".
If you mean the freeze plugs at the back of the block that are covered up by the bell housing, then you would have to either drop the trans or pull the engine whichever seems easier.
It's usually easier to drop the trans.
What is the value of a 1967 Oldsmobile Cutlass Supreme?
http://www.nadaguides.com/default.aspx?LI=1-22-1-5006-0-0-0&l=1&w=22&p=1&f=5012&m=1134&c=11&da=-1&y=1967&da-1 fill out details here.
Outside door wont open 1997 olds cutlass supreme?
Take inner door panel off and look inside the door and you will probably find a rod off the outside door handle.
How do you replace the water pump on a 1991 Oldsmobile Cutlass Supreme?
2. Drain coolant...if new save and reuse. If not replace it with premix 50/50 antifreeze. You can mix your own but for convienence use the 50/50.
3. Remove air cleaner (if located in the way), and remove Radiator overflow tank.
4. Remove serpentine belt and tensioner...(rotate tensioner counter clockwise to release belt tension (write down routing of belt before removing)and remove the belt fromthe auxillary components and slowly release the tensioner. On 3.1 and 3.4L engines remove tensioner retaining bolt and detach tensioner assembly from the engine.
5. Remove alternator and its brackets (AC compressor if necessary)
6. Remove small belt guard just above water pump (on 3.1L)
7. Remove water pump mounting bolts (around the perimeter of the pump- approximately 5 of them) and remove the pump. If it is stuck tap with a SOFT-face hammer GENTLY!!!
8. clean fastener threads and any threaded holes in the engine to remove corrosion and sealant. Remove any residual gasket material left on block.
Use Lacquer thinner or acetone to clean the engine and water pump surfaces that will come into contact with each other.
Apply NEW gasket if not attached to H2O pump
Installation is:1. Attach pump and gasket to eng block and start the bolts finger tight Tighten in 1/4 turn increments to torque Torque for 3.1 and 3.4L is 89 in-lbs....THIS IS NOT VERY HARD!!! TIGHTEN WITH SOCKET AND RACHET TILL 1/2 TURN PAST TIGHT!!!!!
2. reinstall all parts you took off to get to this darn thing.
- NOTE*****
This project is best done with at least two friends and a whole lot of your choice of alcoholic beverage. Have Fun!!
Where is the evap canister located on a 1997 Oldsmobile cutlass supreme?
Under vehicle, driver side, below seating area, front of fuel tank and in front of the fuel filter.
Where do you find hubcap keys?
If they aren't in your trunk, check your glove box. If you have lost them, the dealer can order new ones off your VIN number. If you are really desperate, you can mold you an emergency key using 2-part epoxy putty. Make sure that you pull it out before it sets up!
Where is the starter relay on a 1992 Cutlass Supreme?
GM usually uses a combination solenoid/switch/relay located beside the starter. One end engages the starter. The other end connects the battery to the starter motor.
How do you replace the alternator on a 1997 Oldsmobile Cutlass Supreme?
Depends if it is the 3.1 or 3.4. I have a 3.4L and I let the dealer do it. The car had to be raised and the engine lowered since the alternator is located on the rear of the engine towards the bottom. See question regarding the 1995 Cutlass Supreme . Same applies unless you have the 3.4 version of engine.
REGULAR GM ATF FLUID
Where is the starter located in a 1990 Oldsmobile cutlass supreme?
If the vehicle is a Front Wheel Drive vehicle, the starter will be located in the front lower part of the engine. Just look for a large black wire that is attached to the motor and just follow the wire and it will lead you directly to the starter motor. Good Luck.
How do you replace a heater core on a 1991 Olds Cutlass Supreme 31 V6?
its very simple man its located under the dash in a black box. its right under the controls where the ac is. make sure u take the positive battery cable off before working on it. the hardest part is finding it once u do is easy from there. just take out the other and put the new one in. it is recommended that u should flush out your system but its not really nessacary.
What can you do if the key broke off in the ignition?
If you can see the broken end of the key, sometimes a straightened fine fish hook can be inserted and "grab" on to the brass of the broken key. good fishing! EGAD
I have a 96 olds cutlass supreme 3.1 liter that I recently charged the AC. I used the 134A refrigerant. The refrigerant that I purchased had a fitting for the small port. I had some difficulty finding the small recharge port. At first, all I could locate was the big port and it is on the driver's side, between the Air cleaner box and the wheel well. But, there are two. Yes, there are two ports on most vehicles I have seen. A big port and a small port. Which I later located the small port on the driver's side UNDER the Air filter box. First, take loose the top section of the Air cleaner box (4 Screws philip/flat), then unscrew the hose clamp at the back of the top of the air cleaner box (flat). Take out the air cleaner (good time to change it if it needs it), then there is a bolt in the bottom of the box, but I can't remember what size it was, then lift and push it towards the radiator to remove. Then you will be able to see the small recharge port. Attach the refrigerant hose, start the engine, turn on the AC and push the button. It will suck in the refrigerant when the compressor starts. Don't put the AC on the MAX setting, just AC and turn the fan wide open.
Should have push pin type locks all around the bottom of panel pry these out and then lift up to release the area around the window
