0
Saturn S-Series
The first series of Saturn cars, the Saturn S-Series was part of a compact car family produced between 1991 and 2002. It was available in sports coupe, sedan level and sedan wagon variants, with either 4-speed automatic or 5-speed manual transmissions.
2,389 Questions
Where is the crank sensor on a 1999 Saturn SL1?
It is located on the back side of the block (firewall) almost directly in the center, under the intake manifold. You will need to remove the electrical connector and retaining bolt. Then "lift" it out. Good Luck.
Your Saturn sl1 1995 is leaking trans fluid what do you do?
It could be as simple as a few bolts need to be tightened, or it could be a worn/failed seal.
What does diagnostic code p0410 mean for a 2002 Saturn sl2?
Trouble code P0410 means:Secondary air injection system malfunction
Where is the fuel pressure regulator located on a 1997 Saturn SL1?
the FPR(fuel pressure regulator) is part of the fuel filter assembly. Which will cost you about $60-$80
How to disable 2000 Saturn sl1 factory security?
theres no way to disable this feature if light is on key igintion has gone bad or going bad
How do you find the radio code for a 1996 Saturn SC2?
try this website. if not applicable, do some searching on the net ("gm radio code Saturn") until you find a site that doesn't charge for the code ... there are a few out there. good luck.
http://www.teammiata.com/libs/radio-codes.htm
What are the connecting rod torque specs for a 2000 Saturn with a 1.9 dohc?
I believe these are torque to yield bolts and the specs are: Initial torque to 19 Ft/Lbs Tighten an additional 75 degrees It's also not a good idea to reuse these bolts as they are stretched when tightened.
How do you install a MAP MAF sensor enhancer in a 98 Saturn SL2?
There is no such thing as a MAP enhancer. If you have this throw it out or get your money back as it will do nothing for the car but decrease mpg while not doing anything for performance
How do you unlock the passenger door when it has locked when trying to open the car?
You use your key to unlock the door. Then it will be open. If not, a locksmith can help.
How do tighten serpentine belt 97 Saturn SC2?
You don't tighten a serpentine belt. The tension is controlled by a tensioner. If it is loose, then the belt has stretched and needs replacing.
How do you test ignition module 1992 Saturn SL?
Switch parts with another 91-95 Saturn and drive both until completely warmed up to see which car displays any temperature sensitive problems.
How much oil does a 2002 Saturn SC2 take?
put in 4 quarts wait 15 minutes
check the dipstick
add as needed
NOTE* 1 quart will raise the level from the bottum to the top of the hach marks on the dipstick
Why is my engine coolant thick and yellow?
oil is emulisifieing,drive the car at the speed limit on highway for 25,30 miles at a time, this will get the oil up to correct operating temp.
How do you replace the exhaust gas recirculation control circuit on a 2002 Saturn SL1?
You don't. It's integrated into the PCM. Check the EGR valve itself - remove it and check if the plunger sticks. If you can get it to stick, that's your problem. Also, check the wiring harness. If nothing is visibly bad, bolt the valve back on and take the car to your local shop.
My sl2 won't start what could be the problem?
That happened to my grandma. Her problem was that she had a twig stuck in her engine. Try checking your engine for faulties.
This keeps happening to me too. My key won't turn at all sometimes so I did some research and it is a common problem check out this site.
http://www.consumeraffairs.com/automotive/saturn_ignition_lock.html
What makes the electric fan turn on on a 1999 Saturn sc 2 coupe?
The computer with input from the engine coolant temperature sensor.
Why you need to add refrigerant oil to the compressor?
The oil is there for one purpose ,thats to lubricate the compressor ,but it also traveles with the refrigerant through the system and when you have a leak it will be forced out the place where you have the leak ,thus after awhile you will lose some oil ,generaly the leak will be around the seal in the compressor.
How can you fix a crack in engine block?
It can be done but unless the block is rare or an antique, it isn't worth it. Buy a new or good used block to replace the cracked one.
Where is the Shift solenoid located on a 2002 Saturn SL1?
The solenoids are located in the upper housing of the transmission. to get to it, you will need to remove the air intake tube, along with air filter box. use a 10mm socket on the holding bolts. Becarefull of the wire connector for the "ambient air temp" sensor. Remove the battery hold down bracket, also 10mm, along with the battery (8mm). Remove the two 13mm bolts in the lower battery tray, and the 13mm bolt that is through the driver side wheel well into the lower part of the tray. Remove the engine computer from the tray (10mm) and set aside. Remove the battery tray completely to reveal the upper transmission housing. Remove the square wire connector (7mm) on the top of the transmission. Remove the outer cover bolts (8mm i belive) pry the cover off to reveal the valve body. Remove the 13 bolts in the valve body (fig1) and remove top cover of the valve body. with all the bolts removed you should beable to take the top cover off to reveal the black plastic circuit board in which the transmisison wireing harness plugs into. (fig 2) remove the board carefully and you will have access to the solenoids. The solenoids are labled for you in Fig 3.
The shift solenoids should OHM out at 4.5 Ohms, GM has made some changes according to Technical service bullitens. see Fig 4
When reassembling the valve body. be sure to tighten the cover bolts over the solenoids to 11nm or 8ft/lbs. any more and the solenoids can bind. If you replace the pressure solenoid, or are attempting to, you will need to reset the transmission solenoids with the Saturn Service Stall System.... of course only available if you take the car into the dealer ship.
How do you reset the change oil soon on a 2000 Saturn Ls1?
I haven't worked on the LS1, but the LS2 has a fuse/relay panel next to the battery. I assume that they're similar.
Remove the fuse/relay panel cover and you'll see a button labeled "oil".
Turn the key on, but do not start the engine.
Press and hold the oil button for between 5 and 10 seconds. You'll hear the dashboard chime that indicates that the reminder has been reset.
