0
Toyota T100
The T100 was a pickup truck manufactured by Toyota Motor Corporation from 1993 to 1998. The 1993 T100 model was powered by a 3.0L V6 engine, which was capable of producing 150 horsepower.
533 Questions
Where is the 1996 Toyota t100 transmission fill cap?
On my 98 it is the red/orange cap on drivers side towards the heatshield. Mine also has a metal clip to hold it and no markings on top which I found odd as well. How hard is it to put "Transmission" on it.
Where is the ac and heater fuse located on a 1993 Toyota pick up truck 4x4?
on the t100 its under the hood on drivers side. in a little box.half way down the fender well. hope that helps
Where is the Fuse box in the Toyota t100?
Its on the left side of the cabin directly next to the drivers left foot.
What would cause your 1993 Toyota t-100 idle rough and the idle will not stay still?
Either timing belt and pulleys or distributor... had to replace both on mine and the coils were shorting out and so were the wires.
What kind of refrigerant does a Toyota t100 use?
The 1997 Toyota T100 pickup with 2-wheel drive and a 3.4 liter EFI DOHC 6-cylinder engine uses R-134a refrigerant. The capacity is 23 ounces.
Will a 3.4 L engine from a 96 Toyota T100 fit in a 1990 4runner?
If you have the 3.0L engine with a manual transmission it is a direct bolt up i dont know about the automatic but i am sure it is the same if you are switching from a four cylinder to the 3.4L then it requires a lot more work but it can be done a well
How do you Reset check engine light 1996 Toyota t100?
Simple. Remove battery cables and wait 15 minutes. If light comes back on check code and repair.
How do you remove the panels to get at the speakers rear and front?
the back panels can be removed by gripping the end of the panel from the trunk side and pull outward s gently there are several clips that needs to be disengaged for it to come out. As for the front i have no idea..
Pop up the corner of the rear seat and that will give you access to one bolt on the bottom of the side panel. Once removed you can push up on the side panel for easy removal.
How do you replace the outside driver-side door handle on 1997 Toyota T100?
buy the new part..about 100.00 new. remove inside door panel , remove three bolts , disconnect cable and pull out old assembly. put new one in and do the steps in reverse.
Where is the neutral safety switch on a 1991 4WD Toyota Pickup and how would you replace it?
the neutral start switch is located on the right side of the transmission housing. It can be adjusted or if it fails continuity check must be replaced. to adjust put trans select lever in N.loosen the bolt at the top right and align the groove in the end of the control shaft with the vertical index line on the switch by pivoting the switch, then tighten the bolt. In park or neutral you should have continuity between the 2nd and 3rd terminals from the right on the bottom looking into the connector with the snap clip on top. If not you will need to replace it.
Faulty fuel pump, fuel pump relay or fuse, fuel filter, connectors or possibly even something else... who knows what without first checking?
Where is the neutral safety switch on Toyota tercel?
Two different switches, two locations. 1. The Neutral Safety Switch prevents the shift leaver from been moved out of park unless the ignition is on and the break peddle is applied. On 1991 it is located inside the plastic counsel below the shift handle. Failure of this switch may cause your vehicle not to start. 2. Not to be confused with the above is the Neutral/Reverse switch. One of its functions are to activate the reverse lights. It is located at the end of the shift cable on the transmission (1991 AUTO) facing the rad. MC
How do you remove the grill on a 93 Toyota t 100?
There are uphostlry clips all along the bottom of the grille attached to the bumper, the obvious top bolts or clips, I think three hidden clips in the center, then hidden screws behind corner marking lamps, its way better to cut the clips, the plastic grills are very brittle, autozone has a good illustration of the grille it will give you a good jumping off point. DN901
What does chassis look like ON TOYOTA T100?
Who cares! Real Americans drive American trucks. Look at a F150 chassis.
How do you replace blower motor on 94 Toyota truck?
On the passenger side under the dash is the blower motor held in with 3 small screws. First unplug the wire harness to the blower and remove the 3 screws. Installation is in the reverse order
Are there anti lock brakes on a 1990 Toyota pickup?
The 1990 Toyota pickups did come standard with an anti-lock brake system or ABS. New parts for this system may be purchased at various auto-part stores or through the Toyota dealership.
Im changing the spark plugs on your v6 t100 but can only find three?
My 1997 T100 is Fuel Injected. On the Passenger Side there are 3 black boxes that control the fuel/firing order. Each box contols 1 Passenger Side spark plug and 1 Driver Side plug. The boxes have small bolts. Remove them and store AWAY from engine. Pull box up and you will find the spark plug wire tube attached and the port for the plug. TWO things to remember: You will need a magnetic tool to remove loosened plugs and you can only buy Three plug wires (for the driver side). The passenger side requires a new box. Around $30.00 each. Mine are still going at 165,000 miles. This is great in not requiring a $2000.00 idiot CPU chip when the firing order goes bad like in American made cars. Lov my Toyota!
CGA stands for the Compressed Gas Association. A CGA fitting is standardized system for the attachment of a compressed gas cylinder to the required regulator or transfer line. Examples of CGA fittings would be CGA-580 for Non-flamable, Non-oxidizing gasses such as Nitrogen, Argon, or Helium. CGA-590 is used for compressed air and CGA-326 is used for Nitrous Oxide.
There are approximately a dozen commonly used CGA-fittings, with others used for special purposes.
These welding fittings are typically used for welding applications, but can extend to other application such as medical and other gas uses.
The fitting standards are designed to make the gas connections leak tight and also prevent different fittings from being mixed up. For example, flamable gas fittings have a left hand thread fittings. Oxygen and inert gases have right hand thread fittings. Since a left hand thread fittings cannot be threaded onto a right hand fitting, it is impossible to connect the fuel gas to the oxygen and vise versa.
It is easy to determine whether the fitting is a left hand or right hand thread. The left hand fittings all have a small cut or slash on the nut of the fitting that denotes the left hand thread.
