Buick Regal

You should be able to find a shop manual at your local library -- make copies of the right sections as they are usually only available in the REFERENCE section...good luck :)

My envoy did this also when the battery died. installed new battery and key came out.

Pop the lid off the reservoir and bend the metal ring that holds the tank against the fender away so the tank is loose at the top. At the bottom there should be two screws that just need to be loosened not taken out for the tank to slip upwards out of position. These screws may need to be acessed by removing the plastic cover that is beside the fuse block and extends down the side of the wheel well. If your car is like mine the hose is what needs changing not the tank itself. it will feel damp and swollen.

the power color is red blue and yellow

The coolant level sensor in the coolant reservoir detects the coolant level is low. The coolant system must have a leak in it somewhere. Have a trusted mechanic diagnose it soon before you do damage to the engine.

If you mean passenger capacity, it is 5. If you mean oil capacity, it is 4.5 qts. If you mean fuel capacity, it is 18 gallons.

I just replaced the drivers side outside mirror (glass only) on a 2001 buick park avenue ultra,I grabbed the glass on both side of the mirror and popped it straight back .there were three wire connectors that I carefully unplugged,I plugged the connectors onto the new glass, and lined up the clips in the center of the back of the new glass and popped the glass back in place.It took about 15 minutes. good luck

you cannot fix the timing on your tbird as it is electronically controlled and does not have a distrubutor. have your camshaft or crankshaft sensors checked

Well after taking off the caliper, and have taken the old pads off. You are going to have to push the caliper cilinder back in with or with-out opening the bleeder ( the nipple on it). After that, you will see a small metal ring that moves around, your brake pad snaps onto that n that is what holds your inner pad into place, the outter pad slides n holds onto the outter part of the caliper. Replace n bleed if you need to.

Yes

the starter is on transmission's side above the right drive axle It bolts on close to where the transmission bolts to the engine. It's held on by a few bolts and is about the size of a 12 oz pop can. You should be able to see it without getting under the car.

Loosen rad petcock or one end of lower hose to drain rad. Remove the 2 or 3 bolts on water outlet housing. Tap gently to remove the outlet. Remove stat from outlet. Clean gasket surface. Install new stat the same way old one came out with new gasket with sealer or o-ring. CAREFULLY snug the 2-3 bolts evenly so as not to break the housing. Add coolant, keep rad cap off for 20 minutes to bleed out air and fill with coolant. Check for leaks. Done. I hope this helps you. Mark

there is a screw on either side of the dash where the doors open remove them and gently pull the dash out

Shorts are what come to mind. Try to follow your wires and check for cuts or bare wires.

Good Luck!

My turn signals are not working on my 92 buick regal.

Look on the inside of the liftgate and you'll spot a plastic trim panel/piece directly behind the High Mount brake light. Gently pry this piece off and you'll have access to the bulb and socket.

4 inch, 4x6, and 6x9

To replace the blower motor resistor on a 2000 Buick Regal, first disconnect the negative battery cable to ensure safety. Locate the resistor, which is typically found under the dashboard on the passenger side, near the blower motor. Remove the screws or bolts securing the resistor, disconnect the wiring harness, and then install the new resistor by reversing the process. Finally, reconnect the battery cable and test the blower motor to ensure proper operation.

To remove the rear door panel from a 2000 Buick Regal, start by carefully prying off any decorative trim pieces and removing screws that secure the panel, typically found near the door handle and along the edges. Next, use a flathead screwdriver to gently detach any clips holding the panel in place. Once all fasteners are removed, lift the panel upward to disengage it from the door frame, being cautious of any attached wiring for power windows or locks. Finally, set the panel aside and disconnect any electrical connectors if necessary.

On a 1998 Buick Regal, the air filter is located in the air cleaner assembly, which is typically found near the front of the engine compartment. To access it, you'll need to remove the air cleaner cover, which is held in place by clips or screws. The air filter itself can then be pulled out for inspection or replacement. Always ensure the engine is off and cool before servicing the air filter.

In a 2002 Buick Regal GS, the blend door is located within the HVAC (heating, ventilation, and air conditioning) system, typically behind the dashboard. Accessing it usually requires removing the dashboard or the center console, as it is part of the air distribution system that controls the mix of hot and cold air. If you're experiencing issues with temperature control, it may be related to the blend door actuator or the door itself being stuck or malfunctioning.

To change the rotors on a 2001 Jeep Cherokee, you typically need basic automotive tools such as a jack, jack stands, a lug wrench, and various socket and ratchet sizes. Additionally, a brake caliper tool may be helpful for compressing the caliper piston when replacing the pads. While no specialized tools are strictly required, having a torque wrench for properly tightening bolts can ensure safety and proper installation.