0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
Where is flasher relay for 2000 Chrysler Concorde?
how to replace the flasher on a 2000 chrysler concorde LXI
How do you remove 96 Chrysler Concorde radio?
Remove bezel/trim from radio. There are no screws, it snaps off. Begin to loosen the trim from the bottom. Now, there should be two bolts (10 MM), one is on the bottom left and the other is usually on the top right. Unscrew these two bolts and slowly slide the radio out. There will be two plugs in the back, one black and one gray. Carefully unplug these. Now, unplug the antenna. Now you should be able to completely remove the radio. When you go to buy the replacement factory radio remember that the 96 Concorde uses the old style-90's wiring...has two plugs, a black one and a gray one. You must use the older style radio if going with the OEM Chrysler radio on a 96 Concorde
How do you replace the thermostat located on a 1997 Chrysler Concorde?
The thermostat for a 1997 Chrysler Concord is located on the top front part of the engine. Follopw the big radiator hose to the top of the engine, where it connects to the thermostat housing. It has two bols that are easily accessible from the top. Remove the two bolts pull up on the thermostat housing. Take out the old thermostat and replace with a new one. Also, replace the gasket as well. Something else that may be helpful I found when changing my thermostat. Check to see if the thermostat housing has a bleeder valve on it. This is a just a small piece that can be turned with a wrench. If the engine is cool, you can attatch a small tube to the bleeder valve and open it to drain off any coolant that may still be in your upper radiator house and will prevent you from having any coolant in the house splashing out all over your engine when you remove the thermostat housing later. Just make sure to tighten the valve again before topping off the coolant after changing the thermostat.
How do you replace the stop light switch in a 1998 chrysler Concorde?
brake light switch is mounted by the brake pedel remove lower panel above brake pedel and then you will see the switch should be able to turn the switch to replace
How do you replace the headlight bulb located on a 2002 Chrysler Concorde?
I've done this many times. Living in Washington, you find your lights are on a lot in the rain, etc. Pop the hood and you will see the wells where the headlights are located. It's pretty straight forward, no tools are required, but it is a knuckle buster. In the well you will see either a black or white plastic part that has a wrapped electrical cable coming from the back. The part is a 3" diameter and cylindrical in shape. It appears like it is attached to a sheet metal piece. (and it is) Get a hold of the part with your hands and turn it counter-clockwise. If you can't turn it with your hands get a large vice grip, but dont over squeeze on the vice grips you don't want to break this part. Once you have the part loosened, (about a quarter to an eight of turn will move it out of its locking grooves) just pull it carefully straight out. Be careful the bulb is in this tube. Carefully pull the bulb out. Insert the new bulb, position the tube back in its hole, turn it clockwise and that's it. The one by the battery is a little harder. I have had to remove the battery to take out the piece on a couple of occasions. Good luck.\
Where is the Chrysler Concorde Fan relay location?
Under the hood on the drivers side is a distribution box, remove the cover and the low speed and high speed fan relays are inside there.
Where is the heater core located on a 2000 Concorde and how can you fix it?
The heater core is underneath the dash in the middle section right behind the console. You can fix it by removing the dash.
How do you disable the alarm on a 2002 Chrysler Concorde?
The factory alarm can not be disabled. It can be reset by unlocking the doors with a key or remote.
Relay sticking.
Where is starter located at on a Chrysler Concorde?
How much is the starter for 1998 Chrysler Concorde
How do you replace spark plugs on 2003 Chrysler Concorde 2.7 liter?
Easy job, they are located under the coil's. Disconnect the coil primary wire connector then using a torx bit remove the two screws holding the coil to the valve cover then lift the coil from the engine and remove the spark plug.There are no spark plugs on this engine.
How do you replace kill switch on a 1998 Chrysler Concorde?
Chrysler vehicles do not have a kill switch.
Chrysler vehicles do not have a kill switch.
How do you replace the AC evaporator on a 2000 Concorde lxi?
Unless you are certified by the EPA to handle refridgerant, either leave this one to the professionals, or take the vehicle to a shop to drain the refridgerant. It is illegal to handle or dispose of the refridgerant unless you are certified by the EPA. With the refridgerant removed, # Disconnect the negative battery cable from the remote battery post located near the right strut tower. CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver's/passenger's air bag system capacitor to discharge before attempting to do any work around the steering column or instrument # Remove the instrument panel by removing or disconnecting the following: #* Shifter knob Allen screw #* Both instrument panel end covers NOTE On the LHS or 300M, remove the center bezel prior to the shifter bezel # Using a trim stick tool, gently pry upward on the shifter bezel; then, disconnect both wiring connectors and a light bulb socket connector; then, remove the socket. # Remove the 2 lower instrument panel cover screws (outside end) and disconnect the deck lid release switch wiring connector. Pull the lower instrument panel cover rearward releasing the clips. Remove the cable-to-brake release handle. Pull the cover rearward and remove it. # If equipped for 6 passengers, remove the lower floor bin. # If equipped for 5 passengers, remove or disconnect the following items: #* Center bezel using the trim stick #* Heater/air conditioning housing assembly control switch and the traction control switch wiring harnesses #* Bezel from the vehicle #* Two left side console side cover screws, pull the cover outward and remove from the vehicle #* Lower glove box door; the 2 screws are located at the right console side cover, pull outward and remove it #* 2 bracket screws and the 2 inside the console bin; then, remove the console #* 2 center lower instrument panel nuts #* 4 steel reinforcement-to-lower instrument panel cover bottom bolts #* 16-way DLC from the reinforcement #* left floor duct/silencer pad screw and the pad #* Steering column shrouds #* Shift interlock cable at the ignition switch #* Column wiring #* The under column duct section #* Left panel air conditioning outlet duct #* The 4 brake pedal support bracket-to-column mounting bolts #* Lower the steering column #* Heater/air conditioning housing and the Air bag Control Module (ACM) harness connectors then, the 2 ground eyelets from the floor tunnel near the bulkhead # Using a trim stick, carefully, pry out on the left and right A-pillar trim moldings and slide them rearward to remove them. # Using a trim stick, carefully pry upward on the instrument panel top cover, and remove it. # From both sides, remove the scuff plate screw. Using a trim stick, carefully, pry out the scuff plates and remove them. # Remove or disconnect the following: #* 3 right side cowl panel screws and the panel #* 3 left side cowl panel screws and the panel #* Remove the right side under dash silencer and pad #* 2 right side radio antenna and amplifier harness connectors #* Left side junction block and Body Control Module (BCM) harness connectors #* 8 instrument panel-to-chassis screws #* Pull the instrument panel rearward #* Instrument panel from the vehicle with the help of an assistant # Discharge and recover the air conditioning system refrigerant. # Drain the cooling system into a clean container for reuse. # Place shop cloths in the interior to catch any excess coolant. # Remove or disconnect the following: #* Air cleaner hose and the air distribution duct #* Heater hoses-to-dash panel spring type fasteners and the heater hoses from the heater core. Plug the openings to prevent coolant spillage. #* Refrigerant lines-to-expansion valve nut and separate the refrigerant lines from the expansion valve. Plug the openings to prevent contamination. WARNING The air conditioning lubricant used in this system absorbs moisture readily. Do not leave any portion of the system open for any long period of time. #* 3 heater/air conditioning housing assembly-to-chassis nuts from the engine compartment #* 2 defroster duct screws and the duct #* Heater/air conditioning housing assembly-to-dash panel nuts and screws #* 4 rear seat heat duct nuts and the duct #* Rear seat heat duct elbow push-pin fastener #* Electrical connector from the heater/air conditioning housing assembly #* Pull the heater/air conditioning housing assembly rearward and remove it from the vehicle #* 2 heater core-to-heater/air conditioning housing assembly screws #* Heater core from the heater/air conditioning housing assembly Exploded view of the instrument panel-Intrepid Exploded view of the instrument panel-Concorde Exploded view of the instrument panel-LHS and 300M View of the remote battery cable terminal-LHS, 300M, Concorde and Intrepid View of the heater/air conditioning housing assembly-LHS, 300M, Concorde and Intrepid To install: # Install or connect the following: #* Heater core to the heater/air conditioning housing assembly #* 2 heater core-to-heater/air conditioning housing assembly screws #* Push the heater/air conditioning housing assembly forward (carefully) and install it to the vehicle #* Electrical connector to the heater/air conditioning housing assembly #* Rear seat heat duct elbow push pin fastener #* Duct and the 4 rear seat heat duct nuts #* Heater/air conditioning housing assembly-to-dash panel nuts and screws #* 2 defroster duct and the duct screws #* In the engine compartment, the 3 heater/air conditioning housing assembly-to-chassis nuts #* Refrigerant lines to the expansion valve #* Refrigerant lines-to-expansion valve nut #* Heater hoses to the heater core and the heater hoses-to-dash panel spring type fasteners #* Air cleaner hose and the air distribution duct # Refill the cooling system. # Evacuate, charge and leak-test the air conditioning system refrigerant. # Install the instrument panel by installing or connecting the following: #* Instrument panel to the vehicle #* Push the instrument panel forward #* 8 instrument panel-to-chassis screws #* Left side junction block and Body Control Module (BCM) harness connectors #* 2 right side radio antenna and amplifier harness connectors #* Right side under dash silencer and pad #* Left side cowl panel and the 3 panel screws #* Right side cowl panel and the 3 panel screws #* Install the scuff plate and the screw (both sides) #* Instrument panel top cover #* Left and right A-pillar trim moldings #* Heater/air conditioning housing and the Air bag Control Module (ACM) harness connectors then, the 2 ground eyelets to the floor tunnel near the bulkhead #* Raise the steering column #* The 4 brake pedal support bracket-to-column mounting bolts #* Left panel air conditioning outlet duct #* The under column duct section #* Column wiring #* Shift interlock cable at the ignition switch #* Steering column shrouds #* Left floor duct/silencer pad and the pad screw #* 4 steel reinforcement-to-lower instrument panel cover bottom bolts #* 6-way Diagnostic Link Connector (DLC) to the reinforcement #* 2 center lower instrument panel nuts #* The 2 bracket screws and the 2 inside the console bin; then, the console (5 passenger models only) #* 2 screws are located at the right console side cover (5 passenger models only) #* Two left side console side cover screws (5 passenger models only) #* Bezel to the vehicle (5 passenger models only). #* Heater/air conditioning housing assembly control switch and the traction control switch wiring harnesses. #* Center bezel using the trim stick. #* Lower floor bin (6 passenger models only). #* 2 lower instrument panel cover screws (outside end) and connect the deck lid release switch wiring connector. Install the cable-to-brake release handle #* Light bulb socket. Both wiring connectors and a light bulb socket connector #* Shifter bezel #* Center bezel prior to the shifter bezel (LHS or 300M models) #* Both instrument panel end covers #* Shifter knob Allen screw # Connect the negative battery cable to the remote battery post located near the right strut tower. # Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks. Have the refridgerant refilled at an EPA authorized facility
Is there a AC filter to change or clean in a 2000 Concorde that removes musty smell?
Yes, there's a "cabin air filter" on many cars. It's much overlooked because most people don't know it exists.
Some are under the dash, some are in the engine compartment. Sorry I don't know where yours is--or even for certain that your car has one.
Google for:
cabin air filter
With your car's year, make, and model, and something might come up...we hope.
AnswerAC evaporators are cold enough that moisture in the air is constantly condensing on the outside. Since they are constantly wet, they are an ideal location for fungus to grow. The fungus smells bad once it gets established. You can't really filter out the fungus, since it's on the refrigeration coils and past the filter. The only thing you can do is SOMETIMES an anti-fungal liquid can be sprayed into the AC intake and you can destroy the fungus and get rid of the smell. It's far more common in areas of the country where the air is constantly humid.
A Concorde does not have a cabin filter.
How to remove windshield washer pump Chrysler concord?
Take the car apart as you would to get to the front driver headlight. It involves taking out a few screws, headlight, plastic bottom coverlike under the bumper. It has one bolt that ties the plastic to the fender and it is hidden in a hole in the wheel well. You will se a plastic cover, oval in shape about two inchs long to remove. You will need a long extention tow get to the bolt. I found that on my 99 Concorde I just needed to remove bolts on one side of the car to be able to pull the plastic out far enough to expose and remove the front headlight. That exposes the windshield washer tank. three bolts and a coupl of wires and hoses and its out of there. The pump is attached to the tank. It pulls out of a rubber grommet. The hard part is the first part in locating the bolts to remove the plastic bumper if you will. That drove me nuts for awhile but it was an easy task and after that you know how to change the light bulbs too. Tim
Where is the backup light switch for a 1997 Chrysler Concorde?
I have a 98 Concorde. My backup lights stopped working and I had my independent garage mechanic check it out while working on another problem and he told me the switch is internal,inside the transmission housing. I didn't pursue it futher. I'm not about to have them tear into the transmission just to replace a simple switch. Another example of Chrysler's wonderful engineering.
Why are my headlights dim on my 1999 Pontiac Sunfire GT 2.4?
Well there is 2 ways to check....it could be your alternater or your battery....to check to see if it is your alternater pull of your positive cable and if the car dies it is your alternater if your car don't die then it is the battery and you might want to get that replaced
How many gallons are left in tank after gas light goes on on a 1998 Chrysler Concorde?
usually you only have about 2 gallons.
The TCM (trans computer) has detected a problem and set a code. This causes the trans to go into safe mode and not shift. Have it checked for codes.
