Consumer Electronics

you propaly can't sub panel from 100 amp panel. Just not enough amperage to be worth while. i had to up grade t a 200 amp main first and then I was able to take a 60 sub panel from that.

It depends.

A depletion MOSFET can be used as an ehancemnet MOSFET when it is operated as an analog amplifier. However, a depletion MOSFET can't replace an enhancement MOSFET when it is operated as a digital switch.

When a depletion MOSFET is used as a digital switch, since the junction between source terminal and substrate must be reverse biased, the voltage of the source terminal of an N typde transistor must be tied to Vdd, and it is completely opposite to an enhancement MOSFET.

When a depletion MOSFET is used as an analog amplifer, the source terminal and the substrate are both at the same potential, just like an enhancement MOSFET.

no sadly its over

super8 works on super8 and 8mm on 8mm projectors, some projectors do have a switch to go from one to another

Highly Unlikely. Personal brewers like Keurig machines typically use over 1000 watts of power at a time to rapidly heat water. However you can see what a device's power consumption (in Watts) is if you look at the device's information sticker. The sticker may state the device's power consumption in Watts directly, or it may state the Voltage and Amperage that the machine runs on. You can multiply the volt and amp ratings to find out many watts the device might use (1000mA = 1A).

VoIP stands for Voice over Internet Protocol. It is also referred to as IP telephone or Internet Calling. It is an alternative way of making phone calls that can be very cheap or completely free. The 'phone' part is not always present anymore, as you can communicate without a telephone set. VoIP has been named the most successful technology of the last decade. People prefer to use VoIP for Pakistan for their call centers in order to provide the best communication medium.

HDMI will give you the best connection. It's a digital connection and not subject to loss like an analog connection. Depending on the age of your equipment, you may not have hdmi. If not, use component (red, blue, and green for video alond with red + white for audio) connections.

You didn't say which model Yamaha you have but if it's a newer A/V receiver, you can use it as a switch. Connect all the components to it and then one output to the TV input (again hdmi is best). This will make it so when you turn the receiver to an input, the video will automatically go to the tv. For example, if you put the receiver on DVD, the DVD video show up on the tv. This does mean that you have to have the receiver on to watch tv. I have mine set with hdmi inputs going through the receiver and component input to the tv from the dvr box. That way, if I want to watch the news and forgo the surround sound, you can put the tv input to component and just watch it with the regular tv speakers. If you need hdmi cables, monoprice.com is a good place to look. I have bought many from them and they are very high quality for a low price (around $15 for a 6'. Good luck.

I've read both yes & no... I believe that you won't be able to hear TV sound, unless its a digital receiver radio...

If a bar of copper is brought near a magnet and rubbed it will get magnetized and would behave like magnet. But this would be temporary and this property would wear after some days.

If you are saying that the secondary (output) winding on a transformer seems to be a short circuit, it is very likely to be low resistance and may only be a few ohms if you measure the resistance with an ohmeter. The only way it would actually be a short circuit is if something has been inserted which has shorted the wires or it has overheated and burnt through. In which case there should be an acrid smell. Or if you can see the wires you would see they were burnt.

A short in the circuit it is powering could cause the transformer to overheat, burn out and short.

Error 1053: The service did not respond to the start or control request in a timely fashion.

For this error turn off your printer .

Reboot your computer

And then start your printing all over again.

This error is when the printing service crashes.

If you still get the message printer spooler service not running.

Click start > click run > type in services.msc

Find the print spooler service

Double click on it

And click start service .

Then print .

Mine is on because the oxygen sensors are having an issue. Just took it in to be checked goes in next week to be fixed. Also received a recall couple of months ago I took it in for but I doun't remember what part was replaced.

300

As many as you want. It is the power consumed by the thing(s) plugged in that is of concern.

The Canon SX100 is a great digicam.

Yes, you can. Simply tuck into an appropriate package and fill in the customs forms.

******

There is many sites on the internet that send gifts at any corner of the world like You will have to choose any gift item and then send it to anywhere in the world.

I suspect you are referring to an external power supply for a device, which consists of a transformer and a smoothing circuit of some kind. Look on the device it powers, there may well be a rating plate or an input fuse. You might also find a VA rating or wattage rating. If so, Google for power formulae to manipulate to find amps.

you can use programs like gamemaker and read the manual.

If you want to make ps2 games you can buy a kit for 2500 dollars.

sony has allowed people to make videogames for ps2.

A business' excess inventory needs depend greatly on the shelf life of those goods and the rate at which they are sold. As an example, a deli should not keep a large quantity of excess with meat that can spoil, but an electronics store may wish to keep a large excess in smaller electronic goods such as mobile phone chargers, as these have long shelf-lives and are sold more frequently.

TTL is preferred in n-mos technology because it produces more heat and thus it's preferable in microcontroller circuit but c-mos does not produce waste heat which is why TTL is not preferred in c-mos.

A synchronous generator is operating at lagging power factor (positive P & Q) when it is supplying P & Q to the system. P & Q are positive which means that they are flowing away from the bus where the generator is connected (overexcited case). On the other hand, it is operating at leading power factor when it is supplying P and absorbing Q. The sign of Q is negative which means that it is flowing towards the generator bus (underexcited case).

head phones, iPod, instructions booklet, usb cord, and that's it...

Electromotive force is also known as emf. It refers to the voltage given by an electrical energy source like dynamo or battery.

It is made up of coil...when an AC voltage is applied, it produces magnetic flux which is repelled by another magnet around it . this applies a force against and the fan gets rotated.....

i am sorry if the above info is wrong.......