Dodge Durango

4.8 quarts for GT-S 2ZZ-GE with filter change exactally....

its on the right fender in front of the washer fluid.

I'm in the process of changing one on a 2001 Durango. I've been told the whole dash has to come out. I'm a little scared of setting off the airbag myself. I'm also not sure if the radio will lock up if i unplug it. Needless to say it will probally be an interesting job. Not much info but I hope it will help. you can go on autozone site and they tell u how to take the dash out and core housing

Haynes repair manual, Dodge Neon 2000 thru 2003. Book #30036 I think the question was where is it located on the car, not which book do I buy to find the location. It is located at the end of the cylinder head. Its the black plastic part with an electrical connector on it.

could be a few things. there is a sensor that threads into thefront pumpkin with a plug and 2 wires coming out of it, this sensor could be bad. or the splines on the front drive shafts could be worn out. or a relay switch or fuse could be blown between the 4WD button/lever and the sensor i mentioned earlier. these would be the most common.

I checked all fuses. They are ok. When you switch from 2WD to 4WD you can not hear the any thing from the TK.

6*4.5

Get a heavy mall (Sledge Hammer with a long handle) and hit the rubber part of the tire with considerable force. The vibration should loosen the wheel off the drum. Be careful swinging the mall If you are trying to remove the wheel bearing/hub assembly, you have to loosen the three bolts from the back of the knuckle and hammer on them to loosen the hub assmebly.

Are you joking or just really inexperienced in automotive maintenance? I'll give you the benefit of the doubt! It's on the rear side of the oil pan, located under the truck, attached to the bottom of the motor (that's the beg metal thing under the hood).

The turn signal switch is part of the multifunction switch.

The turn signal switch is part of the multifunction switch.

Usually a sign of a bad ground connection or corroded contacts on the light socket. In other words a poor connection at that blinker.

on the fender rh if your truck is 97, and beside to the gas tank 98-05

6.5 for the front

The vehicle speed sensor is on the top of the rear axle.

The trans output speed sensor is on the driver side tail housing of the trans,

Answered it for myself. Solenoid pack leaking. Dealer charged about $300.00. If there's a next time I'll do it myself and save about 120.00. Can anybody tell me what good warranties are when they don't cover anything.

You must remove the serpentine belt first. A tensioner tool makes that easiest. Drain the coolant out, if it is not old it can be used again. Pull the pulley off the pump, use a screwdriver between the bolts to keep the pulley from moving. Loosen all of them first. then Take off the pulley. Remove the bolts, I think there are six not evenly divided out. Only the front part of the pump gets changed and the housing stays on the engine. Clean all surfaces. Use some gasket sealer (blue Form-a-Gasket) in the depression in the pump going around the outside of the pump. evenly tighten the bolts on the new pump. Re-assemble, add coolant, put back on serpentine belt. Done.

The oxygen sensor is located in the exhaust system on a 2005 Dodge Durango Hemi 5.7. There is a sensor located before and after the catalytic converter.

First you will need to draw a digram of the belt patter if you car dosent have one on the front by the hood latch. Now you need an 18 mm socket. This is used to loosen the belt tensioner that is spring loaded, and is between the power stering pump and the alt. . Pull up on the belt tensioner and slip the belt off at the altanator or wherever it will come off the easiest. Then remove the alt. It only has 2 bolts. Then you need to remove the pully off the water pump (you will need it for the new one, so keep up with it) to be able remove all the bolts from the water pump. The pully has 4 small bolts. And the water pump has 3 large bolts, and i belive 4 or 5 small bolts. There are no hoses conected to the pump so that makes it a little easier. After you remove the old pump you will need to clean the block and remove all the old gaskest completly. Then with the new pump comes a gasket, make sure you put a thin layer of gasket glue on both sides of the gasket. then bolt it back on the the block. Put the old pully on that you saved from the old pump. Bolt the alt back on then put the belt back on (new one if needed) just like you took it off.

The maximum cargo capacity of the 2004 Dodge Durango is 102.4 cu.ft..

The 2006 Nissan Xterra has rear wheel drive.

There is a placard under the hood listing the spark plug gap.

The 2004 Dodge Durango is 6 ft. 4 in. (76 in.)1 one-touch power windows wide.

Y40

No.

The gas tank on the 2005 Dodge Durango holds 27 gal..

You will have to pull of both front wheels. drop the tie rods. un bolt the rack from the frame of your Durango and pop it out. Its not that difficult its just alot of work. i did it on my 2000 durango 4x4 then i put it up on a 6 inch lift with 40 inch tires