0
Dodge Ram Van
The Dodge Ram Van, or Dodge B-Series, was a large van sold by the Dodge division of Chrysler Corporation. The van was launched in 1971 and continued production until 2003, when it was replaced by the Dodge Sprinter.
1,530 Questions
Where is the obd plug on a 1995 dodge b2500 van located?
The OBD (On-Board Diagnostics) plug on a 1995 Dodge B2500 van is typically located under the dashboard, near the driver's side. You can usually find it above the brake pedal, close to where the steering column meets the dash. It may be necessary to remove a cover panel to access it.
Where is the flasher located on a Dodge Ram van?
The flasher on a Dodge Ram van is typically located in the fuse box. It is a small, cylindrical device that controls the flashing of the turn signals and hazard lights. The specific location can vary depending on the model year of the van, but it is commonly found near the steering column or under the dashboard. Check the owner's manual or consult a repair manual for your specific Dodge Ram van model to locate the flasher accurately.
How do you eliminate the chasis corrosion?
bolting a zink block to the chassis will greatly reduce corrosion, the zink sacrafises itself to oxydisation and preserves the parent material. This is done on large cast-iron engine blocks that are considered re-buildable.
try the cool line fitting from the radiator to the transmission i just had that problem on a 1994 mercury
Sometimes you can leak out of the tailhousing of your transmission if the housing seal is slightly damaged
THE SECURITY WILL DISABLE THE VEHICLE IF YOU LEAVE THE VEHICLE UNLOCKED OR ANY WINDOW DOWN WHILE YOU ARE AWAY FOR MORE THAN 3 MINUTES. TO RESOLVE THIS PROBLEM YOU SIMPLY NEED TO MAKE SURE ALL THE WINDOWS ARE UP AND US THE KEY FOB (REMOTE) TO LOCK AND UNLOCK THE DOOR. YOU NEED TO PLACE THE KEY INTO THE IGNITION AND TURN FORWARD TO THE ACCESSARY POSITION. THE SECURITY LIGHT WILL FLASH FOR A BREIF MOMENT, ONCE THE LIGH IS SOLID AND NOT BLINKING, YOU ARE ABLE TO START THE VEHICLE --> It could also be a faulty fuel pressure regulator, or coolant temperature sensor.
I do not know what year Honda you have, but my fuse was on the passenger side. On the end of the dash , if you open the door, there is an access panel to get to some fuses. There should be a diagram on the panel telling you where the radio fuse is located.
Where is the ignition module located on a 1989 Dodge d150 pickup truck?
The ignition module for this vehicle is mounted on the driver side fender well just below the hood hinge and behind a round vacuum diaphram.It is rectangle in shape and has a connector plug at one end(facing towards the front of the vehicle)and is mounted on a aluminum base with cooling fins(much like a small lawn mower engine)
How do you remove an alternator on a 1994 Dodge Ram van 318 V8?
go to Oreilly auto parts or other part store. Buy a Hanes manual specifically for that van and read the step by step instructions. For about $16 it will tell you how to fix anything on your van in simple and easy to read instructions.
How do you adjust the transmission on a 1993 Chevy Lumina van?
To adjust the cable, pull up the cable release at the rear of the throtle body and move the cable all the way to the rear, Then get inside the car and mash the accelerator all the way to the floor. This should adjust it.
It sounds like your wheels are out of alignment, possibly from driving hard over potholes or large bumps in the road.
How do you tighten the alternator belt on a Dodge Ram 2500 Van 5.2L V8?
Below is what I did on my 2002 Stratus 2.4L.
Note: This is a description of how I chose to repair my vehicle and should not be taken as me advising anyone in any way on how or whether they manage to repair their own vehicles.
You have to remove the passenger tire and wheel wall to do it.
1) Engaged parking brake, loosened lugs on passenger front tire.
2) Jacked-up and placed jack-stand.
3) Removed piece of black under-carriage which surrounds the oil filter and attaches to front bumper. There are at least 10 plastic push-pins to remove and I managed to destroy half of them in the process.
4) Positoned belt over lower pulleys and tensioner (as best as possible) then used a bungee to hold the top end of belt up while I worked under the car.
5) Used a 3/8 ratchet and inserted into square hole attached to the tensioner, disengaged the tensioner (moves clockwise) then used a brace to keep the ratchet handle in that position.
6) From top, removed bungee and finished placing belt over alternator, checked the position of entire belt, reengaged the tensioner, and replaced wall and wheel.
Where is the ballast resistor located on a 1985 Dodge V8 Prospector van?
Usually against the firewall in the center section
What is surging in compressor?
Centrifugal and axial compressors will surge when forward flow through the compressor can no longer be maintained, due to an increase in pressure across the compressor, and a momentary flow reversal occurs. Once surge occurs, the reversal of flow reduces the discharge pressure or increases the suction pressure, thus allowing forward flow to resume again until the pressure rise again reaches the surge point. This surge cycle will continue until some change is made in the process or compressor conditions.
Where is the location of the fuel pump fuse on a 1992 dodge van b250?
Look in the fuse panel under the hood. The cover will usually tell which fuse it is. There is also a fuel pump relay in the same panel and it will be marked as well. Both have to be functioning properly for the pump to work.
Check in the clove box
There may not be a cable, it may be electronic (as was the case with my 92). If so, there is a speed sensor on the driver's side of the transmission tailshaft.
How tall is the 2014 RAM Promaster-Cargo-VAN?
The height of the 2014 RAM Promaster-Cargo-VAN is 7 ft. 6 in. (90 in.).
How do you replace a heater core in a 85 dodge ram van?
Take out the screws that hold the AC/Heater housing together and separate it, and it's right there.
Remove motor cover 1995 astro van?
I'm assuming you do not have the owner's manual, because it explains how to do this on page 6-13, so I'll tell you what it says. 1-Move both front seats back as far as they can go. 2-Remove the instrument panel extension ( the thing with the two cup holders and the ashtray ) by removing the two screws on each side at the top of the extension, and the two nuts on the bottom. 3-Grasp the bottom of the extension, lift up, and pull out. 4-Diconnect the connector for the cigarette lighter. Set extension aside. 5-Grasp the top of the heater duct and pull down gently to remove. 6-Remove bolt from engine cover bracket, ( this is about a five inch metal piece at the top right ) loosen the nut on the other side of bracket, and move it out of the way. 7-Lift up on each of the two latches at the bottom of the cover 8-Remove the two screws at the engine cover using a long handled screwdriver. These two screws are on the sides of the cover, about 1/4 of the way from the top. The screws do not come out of the cover, only from the dash. 9-Grasp the bottom of the cover and slide it backwards. Then, lift it up and out of the vehicle. GOOD LUCK
As for the tapping noise, if it is more like a chatter noise near the front, the timing chain may be lose. Starting in 1998 they placed a chain tensioner on the engine to correct that noise. 97 did not have it. With 155K, it is probably ready for a new chain, if it hasn't been done already. You don't want to jump time with a 3.9 as they are an interference engine, meaning the valves will hit the pistons if it jumps time.
Does the noise go away if you give it just a little gas? If so, listen for the chain.
Like others said, it could also be one or more lifters. To replace those the intake manifold, valve covers and rockers must be removed.
You can also look into the Valve Cover on the left side by removing the oil cap and see if it is sludged up at all. If so, you could also not be getting enough oil to the top end, causing your tapping noise. 3.9's are a noisy engine, but a solid tap may not be normal. Hard to say without actually hearing the tapping.
I live in the Northwest and my Dakota handles well in the snow with chains. On the freeway I get about 23 mpg, but since I drive a very short distance to work, around town is much lower. That's my fault, though, as I drive it such short distances.
EDITED TO ADD: Something I forgot to mention. I've had a number of 3.9Ls come in making more of a ticking noise that they owner thought was a tap. It was from an exhaust manifold bolt shearing off and since there is no gasket between the manifold and head, it will leak at that port. Check them also and make sure they are tight and not broken.
Where is the fuel filter located on a 1992 Dodge Ram van?
The fuel filter for your van is located on the passenger side, just underneath the rail, near the back tire.
Disturbances/shockwaves/ripples/ through the air/water/ground.
