0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Where is the tcm located on a 2006 dodge ram 1500?
The TCM is part of the "PCM" or "ECM" as some call it, it is located under the hood on the right side (Pass. Side) of the firewall behind the air cleaner box. It has 4 plug in connectors plugged into it all color coded ( Black, orange, green, and white) the color can be seen AFTER you unplug then from the PCM. ALSO it is always a "safe" idea to disconnect the battery for at least 5 min's before unplugging or plugging in the connecters to the PCM/TCM
Neutral safety switch location 1999 dodge ram sport 1500?
On a 99 Ram "Sport" 1500 4x4 5.9 Gas the Transmission is a 46 RE and the "Neutral/Back up switch" is located on the Drivers side of the Tranny towards the rear right above the pan.
What are the head bolt torque specifications for a 1989 Ford Thunderbird 3.8L V6?
I have the shop manual in front of me with all specifications. I would be happy to assist you if I could understand what you mean...? "Head bolt" - - what head bolt - if you help me on this I will give you the torque spec! Cheers ...and if you do mean cylinder head to be bolted onto block - then it is as follows: Number the two rows of bolts as follows: top to bottom, left to right: 7,3,1,5 (top row) 8,4,2,6 (bottom row) For supercharged engine only (other engines have other specs!!!) Tighten the bolts in numerical order - * Tighten to 65-75 Nm (11-18 lb-ft for those that have not grown up...) * Rotate an additional 90 - 110 degrees (harder!) * Go to next bolt in sequence You do not need to retighten bolts later. This will do. Good luck.
How do you replace a fuel level sensor in a 2000 dodge ram 1500 with a 5.9 liter v-8?
remove fuel tank after draining. remove all lines hoses and wires from top of tank. remove fuel pump assembly by turning large plactic nut counterclockwise. disconnect wires inside pump assembly. slide senor and float from fuel pump assembly.
The systems AC system will run when the defrost is turn on.The manufactor does this to remove humity from the air making it easier to defrost the windsheild.The AC system should only run when the defrost is on though.If you are experiecing a high pressure promblem when the AC is running it is pronbly due to a overcharge of refrigerant.
It is not behind the panel it is up under the dash on the drivers side on the side wall it has a black cover over it and on the inside of the cover there should be spare fuses and a fuse puller tool
How do you remove a dash from a 2002 Dodge Ram 1500 Quad Cab.?
everyone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :)
Lol you post on wiki telling them to go buy a book.. ur a tool.
Nice! that's what I thought the internet was for!
If your windows still work on the switch than it is most likely that the switch is bad I had the same problem with mine and it was the switch
Does a 2004 Dodge Ram 1500 5.7 hemi have posy rear-end?
It was an available option. If you call your local dealer with your vin, they can tell you if your truck was built with it.
It was an available option. If you call your local dealer with your vin, they can tell you if your truck was built with it.
How do you replace voltage regulator on 1997 sunfire 2.4?
you have to replace the whole alternator. It is built in and not external.
What do the codes 37 and 55 for a 1997 dodge ram 1500 mean?
37 Shift indicator light failure, 5-speed
OR
part throttle lock/unlock solenoid driver circuit (87-89)
OR
solenoid coil circuit (85-89 Turbo I-IV)
OR
Trans temperature sensor voltage low
55 End of codes
How many quarts of oil does the 5.7 hemi take for a 2006 Dodge Durango?
7 quarts
Capacities:
Engine, with Wix 51085 Oil Filter.........7 quarts [1]
Cooling System, Initial Fill..........16.3 quarts
Automatic Transmission, 42RLE Initial Fill..........4 quarts
Automatic Transmission, 545RFE 2WD Initial Fill..........5.5 quarts
Automatic Transmission, 545RFE 4WD Initial Fill..........6.6 quarts
Automatic Transmission, Total Fill
5 speed 545RFE 4WD..........14.1 quarts
5 speed 545RFE 2WD..........14.1 quarts
4 speed 42RLE..........8.8 quarts
Wix 58846 Auto Tran Filter [1]
Wix 58843 Auto Tran Filter [2]
[1] 45RFE - Shallow Pan
[2] 45RFE - Deep Pan
Differential, C205F Front..........3.4 pints [2]
Differential, With 8.25 RingGear Rear..........4.2 pints [3]
Differential, With 9.25 RingGear Rear..........4.4 pints [4]
Transfer Case, NV144..........1.7 pints
Transfer Case, NV244..........3.4 pints
[1] After refill check oil level.
[2] Fill to level of fill plug.
[3] Fill no higher then 1/4 inch below plug hole.
[4] Fill no higher then 5/8 inch below plug hole.
TORQUES:
Oil Drain Plug.....25 ft/lbs
Transfer Case
Fill Plug 15-25 ft/lbs
Drain Plug 15-25 ft/lbs
NGK Plugs and Wiresets:
NGK - Ixiridium - NGK2313
Wireset - Direct Fire Ignition - [1]
[1] No Wires Req'd
Wiper Blades:
Driver | ExactFit - T261 | NeoForm - T16260 | Winter - T37260
Passenger | ExactFit - T211 | NeoForm - T16210 | Winter - T37210
Rear | ExactFit - T14C
What is the spark plug gap for 2003 ram 1500 4.7?
The problem might be your fuel filter. I know first hand that when mine collapsed it did the same thing. Also might check the throttle control fuse and cable.
How do you adjust the caster on a 1996 Dodge ram 2500 4x4?
Caster is adjusted by turning the cam bolts on the lower control arms.
What does brake fluid leaking from the left rear wheel mean on a 1996 dodge ram?
I found out it`s the cylinder
Where is the ABS brake fluid reservoir on a Pick up truck 1998 Dodge Ram 1500?
The abs uses the brake fluid from the regular brake master cylinder.
Where is the mass air flow sensor located on a 1997 Dodge Caravan?
A Dodge Caravan does not have a mass air flow sensor.
How do you change the oil in a 2006 vw Passat 3.6?
2006 Volkswagen Passat Sedan (3C2) V6-3.6L (BLV)
Engine Oil, Draining or Extracting, Changing Oil Filter and Filling Oil
03 - Service Procedures
Engine Oil, Draining or Extracting
Special tools, testers and auxiliary items required
¤Oil extractor (V.A.G 1782)
¤Oil absorbent towel (VAS 6204/1)
Engine Oil, Draining or Extracting
Perform the following work procedure:
¤On engines with standing oil filter module, oil filter should be changed before the oil change. Removing the filter element will open a valve and oil in the filter housing will flow automatically into the crankshaft housing.¤If engine oil is drained and not extracted using old oil extraction unit, replace oil drain plug. This prevents leaks.¤Observe waste disposal regulations!
- Extract engine oil using old oil collecting and extracting unit (V.A.G 1782).
- Remove oil drain plug
- Let engine oil drain.
- Screw in new oil drain plug with sealing ring hand-tight.
- Fill up with engine oil. Note oil specification.
Torque specifications for oil drain plug: 30 Nm
CAUTION!
¤Torque settings must not be exceeded¤A torque figure that is too high may lead to leaks or even damage the oil pan.
Oil Filter, 2.0L TFSI, Removing and Installing
Special tools, testers and auxiliary items required
¤Oil drain adapter (T40057)
¤Oil filter wrench (VAS 3417)
¤Torque Wrench (V.A.G 1331/)¤Needle-nose pliers
Oil Filter Housing, Draining
CAUTION!
¤Oil filter housing must be drained before it is removed.¤When screwing in oil drain adapter (T40057), a valve in the oil filter housing is opened.¤If oil drain adapter (T40057) is unscrewed again, the valve closes automatically again.
- Unscrew dust cap - arrow - from oil filter housing.
- Screw oil drain adapter (T40057) into oil filter housing and hold hose into an oil collecting pan.
- Allow engine oil to drain.
- Unscrew oil drain adapter (T40057) again.
The drain valve - 1 - should seal flush with the under side of the oil filter housing - 2 -.
Oil Filter Insert, Removing
- The oil filter housing can be loosened using the oil filter wrench (VAS 3417).
- Then unscrew by hand and remove together with oil filter insert.
- Remove oil filter insert - 2 - from oil filter housing center tube - 4 -.
Seal, Removing
CAUTION!
The oil filter housing sealing ring - 3 - must be replaced each time the oil filter insert is changed - 2 - or every other time the oil filter housing is loosened.
The sealing ring is equipped with a so-called "service flag " - A -.
¤The sealing ring can be gripped at the "service flag" - A - with a suitable tool and then removed from the seal groove.
- Remove sealing ring - 1 - from oil filter housing seal groove - 2 - by pulling sealing ring out with needle-nose pliers - 3 - on the "service flag" - arrow -.
Seal, Installing
- Lubricate sealing ring - 3 -.
- Lay sealing ring in oil filter housing seal groove so service flag - A - is aligned toward top.
- Press sealing ring into seal groove and check whether ring contacts entire groove evenly by feeling above sealing ring with finger - arrows -.
Oil Filter Insert, Installing
- Press new oil filter insert - 2 - onto oil filter housing center tube - 4 - as far as stop.
Oil Filter Housing, Installing
- Install oil filter housing - 4 - with new sealing ring - 3 - and new oil filter insert - 2 - by hand until almost on oil filter housing stop - 1 -.
- Tighten oil filter housing - 2 - to 25 Nm.
- Install dust cap - arrow - hand-tight in oil filter housing.
Oil Filter, 6-Cylinder FSI, Removing and Installing
Special tools, testers and auxiliary items required
¤Torque Wrench (V.A.G 1331)
- Open oil drain plug - 6 - to empty oil filter housing
- Loosen screw cover - 4 - at hex head.
- Remove oil filter insert - 2 -.
¤Observe waste disposal regulations!
- Replace O-rings - 1, 3, 5 - and lightly lubricate rings before assembly.
- Now insert a new oil filter insert.
- Tighten screw cover - 4 - to 25 Nm.
- Oil drain plug - 6 - is tightened to 10 Nm.
2.0L TSI
Special tools, testers and auxiliary items required
¤Oil filter wrench (3417)
¤Torque Wrench (V.A.G 1331)
Removing
- Loosen the oil filter cartridge - arrow - with the oil filter wrench (3417).
- Loosen the filter several turns. Wait a few seconds so the oil between the filter and the housing can flow back into the engine oil pan. Now remove the filter completely.
¤Observe waste disposal regulations!
Installing
- Clean the sealing surface before installing the oil filter cartridge.
- Lightly oil rubber gasket on new filter. This achieves the best possible seal when tightening the filter.
- Tighten the filter to 22 Nm with the torque wrench (V.A.G 1331).
2004 dodge ram 2500 radio removal?
you have to open the glove box and remove the screw on the left and the screw on the hook by the glove box then every thing else snaps out.
What would cause speedometer failure as well as dash brake and abs lights on a 2004 dodge ram?
I had the same thing happen on an 1999 dodge 2500 and it was the rear speed sensor located on top of the back rearend got from dealer for about $35.
