0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
What type oil for yanmar 1500 trans?
For the Yanmar 1500 transmission, it is recommended to use a high-quality agricultural or hydraulic oil that meets the specifications of ISO VG 32 or a suitable equivalent. Common options include UTF (Universal Tractor Fluid) or hydraulic fluids specifically designed for agricultural equipment. Always refer to the owner's manual for the specific oil type and recommended viscosity for optimal performance.
What is the axle nut torque on a 96 ram 2500 4x4 with the 8800 lb axle?
Front axle shaft nut torque: 175 ft lbs. Rear axle hub nut torque: # Tighten the adjustment nut to 163-190 N·m (120-140 ft. lbs.) while rotating the wheel. # Loosen the adjustment nut 1/8 of-a-turn (120 degrees) to provide 0.001-inch to 0.010-inch wheel bearing end play.
Why would the gages not work on a 2000 dodge ram 1500?
under your dash there should be a fuse for your instrument cluster. that is probably the problem.
How do you reset replaced ecm to key?
Attempt to start the engine, it will probably fire then stop, with the security lamp on. Do not turn the switch off, let it stay on till the lamp goes out, (about 10 min) then attempt to start again. Once again it will fire then stop with the security lamp on.
When you have went thru this procedure three or four times, and the new key code is learned, the engine will run.
How do you replace the evaporator core in 2000 dodge ram 1500?
You will need to remove the dash and HVAC housing to access the evaporator core.
Start with disconnecting the battery.
You will then need to recover the Freon from the ac system and drain the antifreeze.
Under the hood you will need special tools to disconnect the ac lines at the firewall, remove the heater hoses, remove the engine computer and remove four nuts that hold the HVAC housing.
Inside you will have to remove the trim on the sides of the windshield, trim at the base of the doors, remove the trim below the steering column, remove the steering column, remove the trim on top of the transmission tunnel, remove the airbag computer, remove screws across the top of the dash and on the sides, unplug numerous connectors and remove the dash. You can just lay it on top of the seats.
The HVAC housing is then held in with two more nuts.
Once you get it out you then remove the screws that hold the Heater core in place. You need to remove the screws that hold the top cover on.
You reverse all steps to install.
Do not forget to fill the antifreeze and warm the engine up before driving.
You will also need access to an ac vacuum/refill machine to recharge the ac.
Something about the vacuum linr being unattached, maybe from the firewall. im trying to figure out the same.
The main vacuum supply line is disconnected or cracked, probably near the engine. All the HVAC doors operate on vacuum. When there is no vacuum the HVAC system goes into defrost mode.
A four wheel drive of weight 25 kg with 500 RPM should have torque?
How much torque? I don't know. Should it have torque? Always. I have a motor that can spin close to 10'000 RPM, but I can stop it with my finger because it has very low torque. A good way to remember this is, the faster it spins, the lower the torque. You can increase the torque by using a gear chain to gear-up, trading RPM for torque. Gearing Down is the reverse.
How do you remove the ignition switch on a 2001 Tundra?
"you can't unless you grind off the bolts from the steering column bracket. Most times people just change the whole steering column because its all part of one unit."
Actually, you can do it without grinding the bolts -
remove the lower trim panel (below the steering wheel)
insert your ignition key and turn it to acc
on the bottom of the ignition switch, there is a button you have to push in and you can then remove the switch
How do you completely remove the bed of a regular cab 1993 Toyota V6?
The truck bed is very easy to remove, just disconnect the fuel fill hose from the body side and the wire connectors from the rear lights and then remove the bed mounting bolts from below and lift the bed off.
How do you know if 2004 dodge ram 1500 alternator is bad?
with vehicle running pull posative side battery terminal off if it quits alternator is bad
Where is the fuel pump fuse for a 2002 dodge ram 1500?
hello i am pretty sure its under the hood on the drivers side in the fuse and relay panel, but it is a relay not a fuse
What is the stock thermostat on a 2006 5.7 liter hemi?
The stock thermostat for a 2006 5.7-liter Hemi engine is typically rated at 203 degrees Fahrenheit (95 degrees Celsius). This thermostat is designed to regulate the engine's temperature, ensuring it operates efficiently by opening and closing at the appropriate temperatures. If you are considering replacing it, ensure to use a compatible part that meets the manufacturer's specifications for optimal performance.
Will 16.5 tire fit on 17'' rim?
nope.. although several have tried, and had disastrous results. 16.5 inch rims can be found cheap enough, check military surplus for hummer rims.. they are all 16.5.
good luck
No, very dangerous.It is possible that the screen has fallen out of the oil pickup tube. To confirm you will need to remove the oil pan, if so it will be obvious
What are the cylinder numbers on a 2007 dodge 5.7 v8?
Passenger side front to back. 2-4-6-8 Driver side front to back. 1-3-5-7
How do you know if the auto transmission fluid is low on 2000 Pontiac Sunfire 2.4 GT?
EDIT:
While the answer provided by someone else (above) is correct on most makes and models, it is incorrect in regards to the the sunfire of production years 2000 and up. There is no dipstick on a 2000 sunfire as I have owned two and know from first hand experience (2.2 and 2.4 although not GT) GM decided that since the fluid never really needs replacing for the life of the vehicle that they could scrap the dipstick all together. Fortunately there is a very accessable red cap on the top of the transmission (driver side) which is labeled. Either take your car in to the mechanic, or top it up yourself. Just be carefull not to add too much fluid or the pressure could cause a leak and possibly a fire should it spill onto the exhaust or engine from what ive been told (informed by a mechanic).
Will 17 inch wheels fit on a 96 dodge ram 1500?
Yes for sure but you need to know what lug it is 5 lug? 8 lug? but they will yes
How much would it cost to replace the throttle position sensor on a 1999 Jetta?
The cost to replace the throttle position sensor on a 1999 Jetta depends on whether the engine is gas or diesel. The gas engine throttle position sensor will cost around $100 just for the part. The diesel engine part is slightly higher. Labor costs are around $75 to $100 per hour depending on where the vehicle will be serviced. This job should take about one hour.
