0
Ford Escape XLS
The Escape XLS is a compact crossover sport utility vehicle manufactured by the US-based carmaker Ford Motor Company. This vehicle is powered by a 2.5 L 4 cylinder engine and features traction control, stability control and curtain/side airbags.
873 Questions
What is the towing capacity for a 1995 dodge ram 1500 short box with a 5.6 liter magnum engine?
Any Ram can tow about 18.000 pounds without any trouble...It;s a RAM
Why does the abs light flash on your 2005 ford escape?
It is important to know what the warning lights mean on a dashboard. The ABS lights flash on any vehicle when there is an issue with the brake system.
How to change egr valve on a 1999 Saturn?
EGR valves are located on top of the engine near the air intake (the big black hose that comes from the air cleaner box). They usually have a few wires and a couple bolts holding them. With a few tools it's pretty easy. The tough part will be the cost for the replacement.
Where is the fuse for the tail lights on a Ford Escape?
Should be the same as parking/dash lights on the lower left kick panel
Where is a diagram for fuse box in 2008 escape?
You can view the 2008 Ford Escape Owner Guide online at :
www . motorcraft service . com ( no spaces )
Click on Owner Guides
It includes the fuse box diagram
Why does your front end squeak on a 2001 gmc Yukon?
i most likely needs to be greased there are several grease zerts on the front end take it to an oil and lube shop and see if that doesnt fix the problem squeaking in the front end could be alot of things. your suspenion need replacing, beaings, loose bolts, or even a loose bumper. best bet is to have it looked at by a licensed mechanic
The park lamp fuse on a Ford Escape is located in the main fuse panel, near the hood release. It prevents the lamp from drawing too much current and will break under excessive load.
What ground clearance does the 2003 Ford Escape have?
The ground clearance of the 2003 Ford Escape is 0 ft. 7.8 in. (7.8 in.).
First do a tune up! Things like new wires,plugs,pcv valve,air filter,distributor cap and rotor button and even the oxygen sensor.Now next remove the entire air cleaner assembly and clean the carburetor with carb cleaner and (suggest using brake cleaner on the linkage ONLY) and then lube it with liquid wrench.Next remove the egr valve directly below the carb has one vacumm line,one electrical plug and has 3 10mm bolts that hold it in place.Note make sure when you remove this you NOTE how the metal gasket on the egr is placed.Just clean this with a small brush and sandpaper,cordless drill brush, with some brake cleaner or carburetor cleaner to clear the carbon buildup out.Reinstall the egr.Now if the truck still runs poorly at idle it could be the exhuast collector just below the exhaust manifold is blocked up,or blocked up catalytic convertor or even the air to fuel valve is defective(which is on the carburetor itself).Start with the tune up,clean the egr valve and repost on this post with the discussion area for a update after you do this and no change or improvement).The year model may be relevant if the truck is fuel injected,because of the specifics is it is not carburated being some b2200 series are not.
Where is the fuel pump reset button on a 2001 Ford Escape?
On a 2001 Ford Escape :
The fuel pump shut off switch ( inertia switch ) is located in the front
passenger footwell behind the kick panel
There is an access hole in the kick panel to gain access to the reset button
on top of the switch
* the kick panel is the interior trim panel , in front of the front door , beside the passengers right foot
Where to buy aerator pumps in metro manila?
Where to but Aerator Pumps and How much will cost 3 HP Thank you
What is the maximum cargo capacity of the 2003 Ford Escape?
The maximum cargo capacity of the 2003 Ford Escape is 69.2 cu.ft..
How do you remove spare tire from under Ford Mariner?
you have to put jack handle together .makes it long like a pole.on the back of your rear bumper,u have a hole might have a lock on it or not.if you do have a lock on hole.there should be a long key in glove box that will unlock lock .if here is no lock on hold than just stick long pole in hole and crank down tire.rember hole should be under your rear plate and bumper
What is the purpose of the oxygen sensor after the catalytic converter?
The second oxygen sensor is now used downstream of the catalytic converter to monitor converter operating efficiency.
What size tool do I need to remove caliper bolts from Mercedes 1999 E320 to replace the pads.?
this is a special design guide (not a regular bolt)
Where is the speed sensor on a 2007 Ford Escape?
if you have cruise try the gray/black wire coming from the cruise control module, in the engine compartment... it should be on the passenger side fire wall, it will also have a black cable going to the engine throttle body.
Why does your car shake during idle and acceleration?
could be the engine mounts. could because of early detonation, which could be caused by overheating. it also could be a rod knock, which is more likely if it keeps shaking during acceleration and higher rpm's.
first thing to check would be if its too hot, watch the temp guage, and make sure it doesnt get too high.
How do you disable the passenger airbag on a Ford Probe?
SYSTEM PRECAUTIONS # Before replacing any air bag component, disconnect the negative battery cable and disconnect the orange and blue clockspring electrical connector, located below the steering wheel. # The air bag components are not intended to be disassembled. They should be replaced if they are defective. # The air bag wiring harness should never be repaired, if it is defective it must be replaced. # Never use an ohmmeter to test the air bag module. Doing so could accidentally deploy the air bag. # When carrying a live undeployed air bag module, carry it so that the trim cover is pointing away from your body at all times. # When placing a live undeployed air bag on a flat surface, make certain to face the trim cover upward at all times. # In the event that the air bag has been deployed, always wear gloves and safety glasses to handle the air bag assembly. The air bag may contain caustic material deposits. # Because of the content of the air bag assembly, a deployed unit must be properly disposed of. # The position of the crash sensors in the front end is very important, if the front end ever suffers any damage of any type, the sensors must be inspected. # If the steering wheel is ever removed, the air bag clockspring connector must be adjusted.
DISARMING THE SYSTEM # If equipped, deactivate the audio anti-theft system. # Turn the ignition switch to LOCK. To disable the air bag system, first disconnect the negative battery cable, then loosen the hood latch pull knob retaining nut and disengage the knob from the lower driver's side undercover Disconnect the negative battery cable and wait for more than one minute to allow the backup power supply to deplete its stored power. Remove the lower driver's side undercover retaining screws then pull the cover down and, if equipped, detach the A/C vent hose from it Locate and disconnect the orange and blue air bag clockspring electrical harness plugs
Remove the driver side undercover and lower dash panel. Disconnect the orange and blue clock spring connectors for the drivers side air bag. Remove the glove compartment and disconnect the orange and blue passenger side air bag module connectors. Passenger's side air bag connectors are located behind the glove compartment
Where is the cylinder 4 on a 2003 Ford Escape?
On the V6 :
firewall
1-----2-----3
4-----5-----6
front of Ford Escape > driver
