0
Ford Ranger XL
The Ranger XL is a pick-up truck manufactured by the American automaker Ford Motor Company. Some of the notable features found in the 2010 model are Electronic Stability Control, and torso and head airbags in the front seat.
4,911 Questions
How many quarts does a 4.0L 1999 Ford Ranger take?
With engine oil filter change ( 5 quarts of engine oil )
Where is the blower motor located on a 1995 Ford Ranger?
On a 1995 Ford Ranger :
The heater blower motor is in the ENGINE COMPARTMENT , near the firewall ,
on the passenger side of the engine
Can you siphon fuel from a 2003 Ford Ranger?
if you use a very small hose you can like the type used in fish tanks
Whats then firing order for 4.0 liter 6 cylinder in a 1997 ford ranger 2 wheel drive?
1-4-2-5-3-6 Look Here:
http://www.boxwrench.net/specs/chevy_sb.htm
==========================================================
Just adding to the correct answer above :
The engine cylinder locations are numbered :
firewall
3 - 6
2 - 5
1 - 4
front of Ford Ranger V6 engine
----------------------------------------------------------------
The COIL PACK towers are numbered :
coil-----3 - 4
pack---2 - 6
plug----1 - 5
How do you change the headlight bulb on a 2002 Mitsubishi Eclipse?
The best thing to do is:
1.) Fold the rubber boot back from behind the headlight/bulb. (You will have to get your finger nails under it to pull it back)
2.) Feel inside near the bulb for a wire "spring", push it dowm and then pull to remove from the headlight body (when looking down on the lamp it is held in place on the left, at least for the left headlight when looking at the front of the car)
3.) pull the whole lamp assmebly out of the headlight through the back.
4.) Unbolt the whole headlight from the frame of the car.
5.) Carefully remove the headlight.
6.) Now you will have enough room to work.... pull the plastic connector off of the three pronged bulb
7.) Insert the new bulb assembly into the headlight (BEFORE REATTACHING THE HEADLIGTH TO THE CAR) and reengage the retention spring. 8.) Put the headlight back onto the car and bolt in place BEFORE REATTACHING THE PLASTIC CONNECTOR PLUG TO THE BULB. 9). Reattach the plastic connector to the blub and fold the rubber boot back over the headlight/bulb assemble
I JUST finished this replacement. It took Faaarrrr too long because I attempted to do it without removing the whole headlight. There is NO room to work if this is not done and pulling the plastic connector off the back of the bulb was impossible. Once I removed the headlight i had all the room i needed and it came off quick.
What engines fit a 1986 Ford Ranger?
Most engine swaps (if that's what you're talking about) that Ive seen are 5.0l V8's out of Mustang's, Explorers, or F-150's. Also have heard of 4BT Cummins Diesel swaps. You can go on TheRangerStation or FordRangerForum and there are many threads that you can choose from to find more information.
2001 ford ranger 2.5 needs to have its idle turned up. how do you do it?
The idle is computer controlled by the ECM with information fed to it from different sensors. Your vehicle must have other issues concerning the 3 necessities. That would be....1. CLEAN COOL FILTERED AIR 2. CLEAN HIGH PRESSURE FUEL and finally 3. STRONG STEADY SPARK. If any of these things isn't quite right the vehicles' performance will suffer. So check out the basic things and go from there. If the CHECK ENGINE light is on or was on, the code(s) can be pulled and remedies found.
How do you replace an AC compressor in a 1999 Kia Sephia?
ANSWER
The compressor is not hard to change, just loosen a belt, some mounting bolts, and a few hoses. The problem, however, is that once you remove the coolant lines, you let air into your a/c system, then it needs to be evacuated and recharged. If you don't, your a/c won't work properly because the air in the lines will cause the compressor to cavitate, and you could ultimately ruin the new compressor, so either way, you should take it to a certified a/c service center.
What color is the Signal wire for IAT Sensor on a 2004 3.5 I-5 Colorado?
The signal wire should be Tan. You should have a Yellow, Black, and Tan Wire. The Yellow being you MAF Sensor Signal. The Black being a Low reference voltage. Then your Tan your IAT sensor signal.
Where is the location of the multi-function switch on a 1997 thunder bird steering column?
I am assuming the "multi-function" switch is the TURN SIGNAL/HI-LO BEAM/WIPER CONTROL SWITCH. It is located on the left side of the steering column.
What is the timing on a Ford Ranger 83 four cylinder?
If your distributor cap is pre-electronic ignition, and is one that can can be unfastened and rotated, do so, moving the cap as you try to start the engine. When it does, rotate the cap till you get the smoothest idle.. lock cap in place. N.B. This is to just get you to the garage
What would cause a 1996 Ranger fuel gauge not to register?
It could be the sending unit which is part of the fuel pump assembly.
To replace the sending unit you must change the fuel pump.
Fairly easy. I replaced mine by lifting up the bed of the truck rather than
removing the fuel tank. Took about 1 hour.
How can you tell from motor oil to transmission oil leaking in the radiator?
there's no way gearbox oil/transmission oil can get in the radiator... only the engine oil can. this usually will happen if the cylinder head is cracked or the cylinder head gasket has failed.
However, Transmission fluid can get into your coolant, by means of a corroded internal transmission cooling line, which is inside the radiator of many model automobiles and trucks... it will look somewhat like pepto bismol at the cap..
What would cause the RPMs to increase when the clutch is in on a 2000 ranger 4-cylinder?
I read another fellows comments about his Ranger RPM going to 2000 to 2200 RPM whenever he shifted gears on his 5 speed manual transmission and he said that it turned out to be his throttle position sensor
How to remove a gear shifter nob?
Unless you see some sort of set screw or locking ring, it screws off.
Actually on a ford you must pull them off. they have a press fit. The shaft is splined and the knob is pressed onto the shaft.
How to find firing order for in line 6 cylinder 2 stroke engines?
Inline 6 cylinder 2 stroke? That is a rare engine indeed. It for sure is not a Ford engine which is the category you listed this question in. What is this engine installed in?
Whats the torque specs for 2007 CBR 600 RR?
The torque spec for the 2007 CBR 600 RR is 49 ft-lbs.
Sources:
http://64.233.167.104/search?q=cache:-Vlt3w5WdmAJ:www.telegraph.co.uk/motoring/main.jhtml%3Fxml%3D/motoring/2006/12/02/nosplit/mfbike02.xml+2007+CBR600RR+torque+ft+lbs&hl=en&ct=clnk&cd=8&gl=us
Can R134a refrigerant be added to a system with R-12 refrigerant?
You really need to flush out the old stuff.
But any garage can do it if they will.
How do you replace the rotors?
how do you remove automatic locking hub.
Well to replace the rotor you must take off the hub. to take off the hub you remove the cap. then there is a snap ring you must push together and pull the inside of the hub out. After that you need a special socket that has 4 prongs on it. take the nut off. then pull the washer out and take off the other nut witch needs the same socket. then your rotor is free to come off just pull.
How do you change the time belt on a 1997 Chevy Malibu?
It has no Timing Belt, it has a Timing Chain.
The writ of replevin is a court order to return property that doesn't belong to you, and where the rightful owner does not have the right to repossess them.
Drag interactions occur when an object moves through a fluid like a gas or liquid.
